EUCHNER AS-i 3.0 Command Interface - Manual (Page 4)

AS-i 3.0 Command Interface Table of Contents
Subject to reasonable modifications due to technical advances Id.-No.: 102875 Issue date - 03.12.07 EUCHNER GmbH + Co. KG
Kohlhammerstraße 16, D-70771 Leinfelden-Echterdingen Tel. +49/711/7597-0, Fax +49/711/753316
4
4.4 AS-i Diagnosis .................................................................................................... 31
4.4.1 Overview of the commands ............................................................................... 31
4.4.2 Get Lists and Flags (Get_LPS, Get_LAS, Get_LDS, Get_Flags)
(GET_LISTS) ..................................................................................................... 31
4.4.3 Get Flags (GET_FLAGS) ................................................................................... 33
4.4.4 Get Delta List (GET_DELTA) ............................................................................. 34
4.4.5 Get list of corrupted Slaves (GET_LCS and GET_LCS_R6 (6CH)) .................. 35
4.4.6 Get list of activated Slaves (GET_LAS) ............................................................. 35
4.4.7 Get list of detected AS-i Slaves (GET_LDS) ...................................................... 36
4.4.8 Get list of peripheral faults (GET_LPF) .............................................................. 37
4.4.9 Get list of offline Slaves (GET_LOS) ................................................................. 37
4.4.10 Set list of offline Slaves (SET_LOS and SET_LOS_R6 (6Dh)) ......................... 38
4.4.11 Get transm.err.counters (GET_TECA) ............................................................... 39
4.4.12 Get transm.err.counters (GET_TECB) ............................................................... 40
4.4.13 Get transm.err.counters (GET_TEC_X) ............................................................. 41
4.4.14 Read fault detector (READ_FAULT_DETECTOR) ............................................ 41
4.4.15 Read list of duplicate addresses (READ_DUPLICATE_ADDR) ........................ 42
4.5 Configuration of AS-i Master ............................................................................. 43
4.5.1 Overview of the commands ............................................................................... 43
4.5.2 Set operation mode (SET_OP_MODE: Set_Operation_Mode) ......................... 43
4.5.3 Store actual configuration (STORE_CDI) .......................................................... 44
4.5.4 Read actual configuration (READ_CDI) ............................................................. 45
4.5.5 Set permanent configuration (SET_PCD) .......................................................... 45
4.5.6 Get extended permanent configuration (GET_PCD) ......................................... 46
4.5.7 Set list of projected slaves (SET_LPS and SET_LPS_R6 (6Bh)) ...................... 47
4.5.8 Get list of projected slaves (GET_LPS) ............................................................. 48
4.5.9 Store actual parameters (STORE_PI) ............................................................... 48
4.5.10 Write parameter (WRITE_P) .............................................................................. 49
4.5.11 Read parameter (READ_PI: Read_Parameter) ................................................. 49
4.5.12 Set permanent parameter (SET_PP) ................................................................. 50
4.5.13 Get permanent parameter (GET_PP) ................................................................ 50
4.5.14 Set auto address enable (SET_AAE) ................................................................ 51
4.5.15 Change slave address (SLAVE_ADDR) ............................................................ 51
4.5.16 Write AS-i slave extended ID1 (WRITE_XID1) .................................................. 52
4.6 Other commands ................................................................................................ 53
4.6.1 Overview of the commands ............................................................................... 53
4.6.2 IDLE ................................................................................................................... 53
4.6.3 Read input data image (READ_IDI) ................................................................... 54
4.6.4 Write output data image (WRITE_ODI) ............................................................. 54
4.6.5 Read output data image (READ_ODI) ............................................................... 55
4.6.6 Set offline mode (SET_OFFLINE) ..................................................................... 55
4.6.7 Release data exchange (SET_DATA_EX) ........................................................ 56
4.6.8 Rewrite DPRAM (REWRITE_DPRAM) .............................................................. 56
4.6.9 BUTTONS .......................................................................................................... 57
4.6.10 FP_PARAM ........................................................................................................ 57
4.6.11 FP_DATA ........................................................................................................... 58
4.6.12 EXT_DIAG ......................................................................................................... 58
4.6.13 RD_EXT_DIAG .................................................................................................. 59
4.6.14 Inverter ............................................................................................................... 60