Yamaha 006IPTO-F0 - Manual (Page 319)

Effects Parameters
319
DM1000 Version 2—Owner’s Manual
Appendix
ST REVERB
Two input, two output stereo reverb.
REVERB 5.1
One input, six output reverb for 5.1 surround, with
surround panning.
OCTA REVERB
Eight input, eight output reverb.
AUTO PAN 5.1
Six input, six output autopanner for 5.1 surround.
• When you press the RESET button, the phase will be initialized to
the setting of the OFFSET parameter.
Parameter Range Description
REV TIME 0.3–99.0 s Reverb time
REV TYPE
Hall, Room, Stage,
Plate
Reverb type
INI. DLY 0.0–100.0 ms Initial delay before reverb begins
HI. RATIO 0.1–1.0 High-frequency reverb time ratio
LO. RATIO 0.1–2.4 Low-frequency reverb time ratio
DIFF. 0–10
Reverb diffusion (left–right
reverb spread)
DENSITY 0–100% Reverb density
E/R BAL. 0–100%
Balance of early reflections and
reverb (0% = all reverb, 100% =
all early reflections)
HPF
THRU,
21.2 Hz–8.00 kHz
High-pass filter cutoff frequency
LPF
50.0 Hz–16.0 kHz,
THRU
Low-pass filter cutoff frequency
Parameter Range Description
REV TIME 0.3–99.0 s Reverb time
REV TYPE
Hall, Room,
Stage, Plate
Reverb type
HI. RATIO 0.1–1.0 High-frequency reverb time ratio
DIFF. 0–10
Reverb diffusion (left–right reverb
spread)
DENSITY 0–100% Reverb density
HPF
THRU,
21.2 Hz–8.00 kHz
High-pass filter cutoff frequency
LPF
50.0 Hz–16.0
kHz, THRU
Low-pass filter cutoff frequency
DIV. 0–100%
Divergence determines how the
front center signal is fed to the
Left, Right, and Center channels.
When set to 0%, it’s fed only to
the Left and Right channels (i.e.,
Phantom Center). When set to
50%, it’s fed equally to the Left,
Right, and Center channels. When
set to 100%, it’s fed to only the
Center channel (i.e., Real Center).
ROOMSIZE 0.1–20.0 Size of simulated room’s reverb
POS L/R L63–R63 Left/right listening position
POS F/R F63–R63 Front/rear listening position
POS CTRL OFF, NOR, INV 1
1. When set to NOR, the position can be set by using the Joystick so
long as the SELECTED CHANNEL PAN/SURROUND [EFFECT]
button’s indicator is on. When set to INV, the Joystick will work
inversely. When set to OFF, Joystick control is off.
ER L/R L63–R63 Left/right early reflections position
ER F/R F63–R63
Front/rear early reflections posi-
tion
ER LVL 0–100% Early reflections level
ER CTRL OFF, NOR, INV 1
REV L/R L63–R63 Left/right reverb position
REV F/R F63–R63 Front/rear reverb position
REV LVL 0–100% Reverb level
REV CTRL OFF, NOR, INV 1
POS RAD. 0–63
Radius of the panning track at the
listening position
ER RAD. 0–63
Radius of the panning track for
early reflections
REV RAD. 0–63
Radius of the panning track for
reverb
Parameter Range Description
REV TIME 0.3–99.0 s Reverb time
REV TYPE
Hall, Room, Stage,
Plate
Reverb type
INI. DLY 0.0–100.0 ms Initial delay before reverb begins
HI. RATIO 0.1–1.0 High-frequency reverb time ratio
LO. RATIO 0.1–2.4 Low-frequency reverb time ratio
DIFF. 0–10
Reverb diffusion (left–right
reverb spread)
DENSITY 0–100% Reverb density
E/R BAL. 0–100%
Balance of early reflections and
reverb (0% = all reverb, 100% =
all early reflections)
HPF
THRU,
21.2 Hz–8.00 kHz
High-pass filter cutoff frequency
LPF
50.0 Hz–16.0 kHz,
THRU
Low-pass filter cutoff frequency
Parameter Range Description
SOURCE
OFF, HOLD,
INPUT1, INPUT2,
INPUT3, INPUT4,
INPUT5, INPUT6,
MIDI
Source specifies the trigger that
will initiate auto pan. When you
press the TRIGGER button in the
screen, auto pan will begin
regardless of the setting of this
parameter.
OFF: No trigger is specified. Auto
pan will always be off.
HOLD: No trigger is specified.
Auto pan will always be on.
INPUT 1-6: The input signal to
effect inputs 1-6 will be the trig-
ger.
MIDI: MIDI note-on messages
will be the trigger.
TRG LVL –60 to 0 dB
If SOURCE is set to INPUT, any
signal with a level greater than
the setting of this parameter will
be detected as a trigger.
TRG MASK 0–1000 ms
Trigger Mask specifies the time
from when a trigger is received
until the next trigger will be
accepted.
TIME 0.1 s–10.0 s
The time after which autopan
starts once it’s been triggered
SPEED 0.05–40.00 Hz Autopan speed
DIR. Turn L, Turn R Autopan direction
OFFSET
–180 to +180
degrees
Pan offset
HPF
THRU,
21.2 Hz–8.00 kHz
High-pass filter cutoff frequency
LPF
50.0 Hz–16.0 kHz,
THRU
Low-pass filter cutoff frequency