KEPCO ATE-DMG SERIES - Manual (Page 9)

ATE-DMG042314 iii
TABLE OF CONTENTS
SECTION PAGE
APPENDIX A - IEEE 488.2 COMMAND/QUERY DEFINITIONS
A.2 *CLS — Clear Status Command ............................................................................................................ A-1
A.3 *ESE — Standard Event Status Enable Command ............................................................................... A-1
A.4 *ESE? — Standard Event Status Enable Query .................................................................................... A-2
A.5 *ESR? — Event Status Register Query ................................................................................................. A-2
A.6 *IDN? — Identification Query ................................................................................................................. A-2
A.7 *OPC — Operation Complete Command ............................................................................................... A-2
A.8 *OPC? — Operation Complete Query.................................................................................................... A-2
A.9 *OPT? — Options Query ........................................................................................................................ A-3
A.10 *RCL — Recall Command...................................................................................................................... A-3
A.11 *RST — Reset Command ...................................................................................................................... A-3
A.12 * SAV — Save Command ...................................................................................................................... A-3
A.13 *SRE — Service Request Enable Command ......................................................................................... A-4
A.14 *SRE? — Service Request Enable Query.............................................................................................. A-5
A.15 *STB? — Status Byte Register Query .................................................................................................... A-5
A.16 *TRG — Trigger Command .................................................................................................................... A-5
A.17 *TST? — Self Test Query....................................................................................................................... A-5
APPENDIX B - SCPI COMMAND/QUERY DEFINITIONS
B.1 Introduction............................................................................................................................................. B-1
B.2 ABOR t Command................................................................................................................................... B-2
B.3 CAL ibrate :CURR ent :LEV el Command ................................................................................................. B-3
B.4 CALibrate:CURRent[:DATA] Command ............................................................................................ B-3
B.5 CALibrate:PASSword Command ........................................................................................................ B-4
B.6 CALibrate:SAVE Command................................................................................................................. B-4
B.7 CALibrate:STATus Command ............................................................................................................. B-4
B.8 CALibrate:STATus? Query .................................................................................................................. B-4
B.9 CALibrate:VOLTage:LEVel Command ............................................................................................... B-4
B.10 CALibrate:VOLTage[:DATA] Command ............................................................................................. B-5
B.11 CALibrate:ZERO Command ................................................................................................................ B-5
B.12 DIAG:EXT Command ........................................................................................................................... B-5
B.13 DIAG:EXT? Query................................................................................................................................ B-5
B.14 DISPlay:CONTrast Command ............................................................................................................ B-5
B.15 DISPlay:CONTrast? Query ................................................................................................................. B-6
B.16 DISPlay:MODE Command .................................................................................................................. B-6
B.17 DISPlay:MODE? Query ....................................................................................................................... B-6
B.18 DISPlay:TEXT Command .................................................................................................................... B-6
B.19 DISPlay:TEXT? Query......................................................................................................................... B-6
B.20 INITiate[:IMMediate] Command .......................................................................................................... B-7
B.21 INITiate:CONTinuous Command ........................................................................................................ B-7
B.22 INITiate:CONTinuous Query............................................................................................................... B-7
B.23 INSTrument:STATe Command............................................................................................................ B-7
B.24 LIST:CURRent Command.................................................................................................................... B-7
B.25 [SOUR:]LIST:CURRent? Query ......................................................................................................... B-7
B.26 [SOUR:]LIST:CURRent:PROTect Command.................................................................................... B-8
B.27 [SOUR:]LIST:CURRent:PROTect? Query ........................................................................................ B-8
B.28 [SOUR:]LIST:DWELl Command ......................................................................................................... B-8
B.29 [SOUR:]LIST:DWELl? Query .............................................................................................................. B-9
B.30 [SOUR:]LIST:INDex Command........................................................................................................... B-9
B.31 [SOUR:]LIST:INDex? Query ............................................................................................................... B-9
B.32 [SOUR:]LIST:SEQuence:NEXT Command....................................................................................... B-9
B.33 [SOUR:]LIST:SEQuence:NEXT? Query ........................................................................................... B-9