beautypg.com
ATE-DMG042314
i
TABLE OF CONTENTS
SECTION
PAGE
SECTION 1 - INTRODUCTION
1.1
Scope of Manual ..................................................................................................................................... 1-1
1.2
General Description................................................................................................................................. 1-1
1.3
Specifications .......................................................................................................................................... 1-1
1.4
Local Control ........................................................................................................................................... 1-1
1.5
Remote Control ....................................................................................................................................... 1-1
1.6
Features .................................................................................................................................................. 1-5
1.6.1
Overvoltage/Overcurrent Protection .................................................................................................. 1-5
1.6.1.1
Programmable Overvoltage/Overcurrent Delay........................................................................... 1-5
1.6.1.2
Crowbar Circuit ............................................................................................................................ 1-6
1.6.2
Non-volatile Storage of Programmed Sequences or Active Settings ................................................ 1-6
1.6.3
User-defined Voltage/Current Limits.................................................................................................. 1-6
1.7
Equipment Supplied ................................................................................................................................ 1-6
1.8
Accessories ............................................................................................................................................. 1-6
1.9
Safety ...................................................................................................................................................... 1-7
SECTION 2 - INSTALLATION
2.1
Unpacking and Inspection ....................................................................................................................... 2-1
2.2
Terminations and Controls ...................................................................................................................... 2-1
2.3
Source Power Requirements .................................................................................................................. 2-5
2.4
Cooling .................................................................................................................................................... 2-6
2.5
Preliminary Operational Check................................................................................................................ 2-6
2.6
Installation ............................................................................................................................................... 2-7
2.6.1
Grounding .......................................................................................................................................... 2-7
2.6.1.1
A-C (Safety) Ground .................................................................................................................... 2-7
2.6.1.2
Isolation from Ground. ................................................................................................................. 2-7
2.7
Fast Mode Conversion of the Ate Power Supply..................................................................................... 2-7
2.7.1
Precautions........................................................................................................................................ 2-8
2.7.2
Lag Network Adjustment.................................................................................................................... 2-8
2.7.3
Crowbar Operation, Fast Mode ......................................................................................................... 2-8
2.7.4
Manual Change-over, Slow/fast Mode............................................................................................... 2-8
2.8
Operating Configuration .......................................................................................................................... 2-9
SECTION 3 - OPERATION
3.1
General.................................................................................................................................................... 3-1
3.1.1
Safety Grounding............................................................................................................................... 3-1
3.1.2
D-C (Output) Grounding .................................................................................................................... 3-1
3.1.3
Power Supply/Load Interface............................................................................................................. 3-2
3.1.3.1
Load Wire Selection..................................................................................................................... 3-2
3.2
Load Connection ..................................................................................................................................... 3-3
3.2.1
General .............................................................................................................................................. 3-3
3.2.2
Load Connection, Method I (Local Error Sensing)............................................................................. 3-4
3.2.3
Load Connection, Method II (Remote Error Sensing)........................................................................ 3-5
3.2.4
Load Connection, Method III.............................................................................................................. 3-6
3.3
Overvoltage Crowbar, Setup and Check ................................................................................................. 3-7
3.3.1
Setup and Check Procedure.............................................................................................................. 3-7
3.4
Local Mode Operation (Keypad Operation)............................................................................................. 3-7
3.4.1
Front Panel Keypad and LCD............................................................................................................ 3-8
3.4.1.1
Command Entry Status................................................................................................................ 3-8
3.4.1.2
Data Entry Status......................................................................................................................... 3-8
3.4.1.3
Display (LCD)............................................................................................................................... 3-8
3.4.1.4
Keypad Functions ........................................................................................................................ 3-8
3.4.2
Turning the Power Supply On............................................................................................................ 3-10
3.4.3
Setting Local Mode ............................................................................................................................ 3-11
3.4.4
Adjusting LCD Contrast ..................................................................................................................... 3-11
3.4.5
Enabling/Disabling Audible Beeps..................................................................................................... 3-11
3.4.6
Enabling/Disabling DC Output Power................................................................................................ 3-11
