H3C Technologies H3C S5560 Series Switches User Manual
Layer 2 - lan switching configuration guide
This manual is related to the following products:
- H3C S5130 Series Switches H3C S5120 Series Switches H3C SR8800 H3C SR6600-X H3C SR6600 H3C MSR 5600 H3C MSR 50 H3C MSR 3600 H3C MSR 30 H3C MSR 2600 H3C MSR 20-2X[40] H3C MSR 20-1X H3C MSR 930 H3C MSR 900 H3C WX6000 Series Access Controllers H3C WX5000 Series Access Controllers H3C WX3000 Series Unified Switches H3C LSWM1WCM10 Access Controller Module H3C LSWM1WCM20 Access Controller Module H3C LSQM1WCMB0 Access Controller Module H3C LSRM1WCM2A1 Access Controller Module H3C LSBM1WCM2A0 Access Controller Module
Table of contents
Document Outline
- Title Page
- Preface
- Contents
- Configuring Ethernet interfaces
- Configuring a management Ethernet interface
- Ethernet interface naming conventions
- Configuring common Ethernet interface settings
- Configuring a combo interface (only applicable to S5560-30F-EI switches)
- Splitting a 40-GE interface and combining 10-GE breakout interfaces
- Configuring basic settings of an Ethernet interface
- Configuring the link mode of an Ethernet interface
- Configuring jumbo frame support
- Configuring physical state change suppression on an Ethernet interface
- Performing a loopback test on an Ethernet interface
- Configuring generic flow control on an Ethernet interface
- Configuring PFC on an Ethernet interface
- Enabling energy saving features on an Ethernet interface
- Setting the statistics polling interval
- Configuring the interface card operating mode
- Configuring a Layer 2 Ethernet interface
- Configuring a Layer 3 Ethernet interface
- Displaying and maintaining an Ethernet interface
- Configuring loopback, null, and inloopback interfaces
- Bulk configuring interfaces
- Configuring the MAC address table
- Overview
- MAC address table configuration task list
- Configuring MAC address entries
- Disabling MAC address learning
- Configuring the aging timer for dynamic MAC address entries
- Configuring the MAC learning limit on an interface
- Configuring the device to forward unknown frames after the MAC learning limit on an interface is reached
- Assigning MAC learning priority to an interface
- Enabling MAC address synchronization
- Enable MAC address move notifications
- Enabling ARP fast update for MAC address moves
- Enabling SNMP notifications for the MAC address table
- Displaying and maintaining the MAC address table
- MAC address table configuration example
- Configuring MAC Information
- Configuring Ethernet link aggregation
- Basic concepts
- Aggregating links in static mode
- Aggregating links in dynamic mode
- Edge aggregate interface
- Load sharing modes for link aggregation groups
- Ethernet link aggregation configuration task list
- Configuring an aggregation group
- Configuring an aggregate interface
- Setting the description for an aggregate interface
- Specifying ignored VLANs for a Layer 2 aggregate interface
- Setting the MTU for a Layer 3 aggregate interface
- Setting the minimum and maximum numbers of Selected ports for an aggregation group
- Setting the expected bandwidth for an aggregate interface
- Configuring an edge aggregate interface
- Shutting down an aggregate interface
- Restoring the default settings for an aggregate interface
- Configuring load sharing for link aggregation groups
- Enabling link-aggregation traffic redirection
- Displaying and maintaining Ethernet link aggregation
- Ethernet link aggregation configuration examples
- Layer 2 static aggregation configuration example
- Layer 2 dynamic aggregation configuration example
- Layer 2 aggregation load sharing configuration example
- Layer 2 edge aggregate interface configuration example
- Layer 3 static aggregation configuration example
- Layer 3 dynamic aggregation configuration example
- Layer 3 edge aggregate interface configuration example
- Configuring port isolation
- Configuring spanning tree protocols
- STP
- RSTP
- PVST
- MSTP
- Protocols and standards
- Spanning tree configuration task lists
- Setting the spanning tree mode
- Configuring an MST region
- Configuring the root bridge or a secondary root bridge
- Configuring the device priority
- Configuring the maximum hops of an MST region
- Configuring the network diameter of a switched network
- Configuring spanning tree timers
- Configuring the timeout factor
- Configuring the BPDU transmission rate
- Configuring edge ports
- Configuring path costs of ports
- Configuring the port priority
- Configuring the port link type
- Configuring the mode a port uses to recognize and send MSTP packets
- Enabling outputting port state transition information
- Enabling the spanning tree feature
- Performing mCheck
- Configuring Digest Snooping
- Configuring No Agreement Check
- Configuring TC Snooping
- Configuring protection functions
- Displaying and maintaining the spanning tree
- Spanning tree configuration example
- Configuring loop detection
- Configuring VLANs
- Overview
- Configuring basic VLAN settings
- Configuring basic settings of a VLAN interface
- Configuring port-based VLANs
- Configuring MAC-based VLANs
- Configuring IP subnet-based VLANs
- Configuring protocol-based VLANs
- Configuring a VLAN group
- Displaying and maintaining VLANs
- VLAN configuration examples
- Configuring super VLANs
- Configuring the private VLAN
- Configuration task list
- Configuration restrictions and guidelines
- Configuration procedure
- Displaying and maintaining the private VLAN
- Private VLAN configuration examples
- Configuring voice VLANs
- Overview
- Methods of identifying IP phones
- Advertising the voice VLAN information to IP phones
- IP phone access methods
- Configuring a voice VLAN on a port
- Enabling LLDP for automatic IP phone discovery
- Configuring LLDP or CDP to advertise a voice VLAN
- Dynamically advertising an authorization VLAN through LLDP or CDP
- Displaying and maintaining voice VLANs
- Voice VLAN configuration examples
- Configuring MVRP
- MRP
- MVRP registration modes
- Protocols and standards
- MVRP configuration task list
- Configuration restrictions and guidelines
- Configuration prerequisites
- Enabling MVRP
- Configuring an MVRP registration mode
- Configuring MRP timers
- Enabling GVRP compatibility
- Displaying and maintaining MVRP
- MVRP configuration example
- Configuring QinQ
- Configuring VLAN mapping
- Overview
- General configuration restrictions and guidelines
- VLAN mapping configuration task list
- Configuring one-to-one VLAN mapping
- Configuring many-to-one VLAN mapping
- Configuring one-to-two VLAN mapping
- Configuring two-to-two VLAN mapping
- Displaying and maintaining VLAN mapping
- VLAN mapping configuration examples
- Configuring LLDP
- Overview
- LLDP configuration task list
- Performing basic LLDP configurations
- Enabling LLDP
- Configuring the LLDP bridge mode
- Setting the LLDP operating mode
- Setting the LLDP reinitialization delay
- Enabling LLDP polling
- Configuring the advertisable TLVs
- Configuring the management address and its encoding format
- Setting other LLDP parameters
- Setting an encapsulation format for LLDP frames
- Configuring CDP compatibility
- Configuring LLDP trapping and LLDP-MED trapping
- Displaying and maintaining LLDP
- LLDP configuration examples
- Configuring service loopback groups
- Index