KEYENCE LJ-V7000 Series - Manual (Page 70)

70 LJ-V7000_COM_RM_E
• Profile
Type:10h~1Fh (10h:Program NO.0, 11h:Program NO.1,
, 1F:Program NO.15)
Category:01h, Item:11h
Target1:00h (headA/wide), 01h (headB), Target2~4:00h
byte Setting Data
0
Peak selection: 0:Standard, 1:NEAR, 2:FAR,
3:Remove X multi reflection, 4:Remove Y multi
reflection, 5:Make invalid data
1 Reserved (fixed as 0)
2 Reserved (fixed as 0)
3 Reserved (fixed as 0)
Type:10h~1Fh (10h:Program NO.0, 11h:Program NO.1,
, 1F:Program NO.15)
Category:01h, Item:12h
Target1:00h (headA/wide), 01h (headB), Target2~4:00h
byte Setting Data
0 Peak width filter: 0:OFF, 1:ON
1 Reserved (fixed as 0)
2 Reserved (fixed as 0)
3 Reserved (fixed as 0)
Type:10h~1Fh (10h:Program NO.0, 11h:Program NO.1,
, 1F:Program NO.15)
Category:02h, Item:01h
Target1~4:00h
byte Setting Data
0 Wide setting: 0:OFF, 1:ON
1 Reserved (fixed as 0)
2 Reserved (fixed as 0)
3 Reserved (fixed as 0)
Note: This setting is not used when one sensor head.
Type:10h~1Fh (10h:Program NO.0, 11h:Program NO.1,
, 1F:Program NO.15)
Category:02h, Item:02h
Target1~4:00h
byte Setting Data
0 Compression (X-axis): 0:OFF, 1:2, 2:4
1 Reserved (fixed as 0)
2 Reserved (fixed as 0)
3 Reserved (fixed as 0)
Type:10h~1Fh (10h:Program NO.0, 11h:Program NO.1,
, 1F:Program NO.15)
Category:02h, Item:03h
Target1~4:00h
byte Setting Data
0 Compression (time axis): 0:OFF, 1:ON
1 Reserved (fixed as 0)
2 Reserved (fixed as 0)
3 Reserved (fixed as 0)
Type:10h~1Fh (10h:Program NO.0, 11h:Program NO.1,
, 1F:Program NO.15)
Category:02h, Item:04h
Target1~4:00h
byte Setting Data
0
Time axis compression count: 2~1000
1
2
Reserved (fixed as 0)
3 Reserved (fixed as 0)
Type:10h~1Fh (10h:Program NO.0, 11h:Program NO.1,
, 1F:Program NO.15)
Category:02h, Item:05h
Target1~4:00h
byte Setting Data
0
Dead zone processing enabled/disabled:
0:disabled, 1:enabled
1 Reserved (fixed as 0)
2 Reserved (fixed as 0)
3 Reserved (fixed as 0)
Type:10h~1Fh (10h:Program NO.0, 11h:Program NO.1,
, 1F:Program NO.15)
Category:02h, Item:06h (ReverseX), 07h ( ReverseZ)
Target1:00h (headA/wide), 01h (headB), Target2~4:00h
byte Setting Data
0 Reverse: 0: OFF, 1: ON
1 Reserved (fixed as 0)
2 Reserved (fixed as 0)
3 Reserved (fixed as 0)
Note: This setting is not used when one sensor head
Type:10h~1Fh (10h:Program NO.0, 11h:Program NO.1,
, 1F:Program NO.15)
Category:02h, Item:08h (Shift X), 09h (Shift Z)
Target1:00h (headA/wide), 01h (headB), Target2~4:00h
byte Setting Data
0
Shift amount: any value in measurement range
(0.001μm unit, Sined 32-bit integer
example:1mm=100000, 2mm=200000)
1
2
3
Note: This setting is not used when one sensor head.
Type:10h~1Fh (10h:Program NO.0, 11h:Program NO.1,
, 1F:Program NO.15)
Category:02h, Item:0Ah (Median (x axis)), 0Ch (Median
(time axis))
Target1:00h (headA/wide), 01h (headB), Target2~4:00h
byte Setting Data
0
Median count: 0:OFF, 1:3 points, 2:5 points,
3:7 points, 4:9 points
1 Reserved (fixed as 0)
2 Reserved (fixed as 0)
3 Reserved (fixed as 0)