Campbell Scientific CR10X Measurement and Control System - Manual (Page 361)

CR10X INDEX
INDEX-9
STD DEV, see Standard Deviation in Time -
[Instruction 82]
Step Loop Index - [Instruction 90] 12-5
Stop Bit 6-7
Storage
see Final Storage, Input Storage, and
Intermediate Storage
Storage and retrieval options, Data OV-20, 4-1, 6-1
Storage Module Pointer (SPTR) 2-2
Storage Modules 4-4
Addressing with CR10X 4-2, 4-4
Commands to (
∗9 Mode) 4-5
Current drain, Typical 14-2
File Mark 4-4
Manually initiated data output (
∗8 Mode) 4-5
Save/load program (
∗D Mode) 1-12
Use with Instruction 96 4-1, 4-5
Storage peripherals, External 4-1
Store Area, see Set Active Storage Area -
[Instruction 80]
Strip charts
Converting 0-360 wind direction output
to 0-540 8-7
Use with SDM-AO4 8-6
Subroutines
Entering 1-2
Label Subroutine - [Instruction 85] 12-1
Port Interrupt Subroutines 12-1
Programming Examples 8-10, 8-21
Subtract - [Instruction 35] 10-1
SW8A Switch Closure Input Module, see
SDM-SW8A
Switch 12V channel OV-3, OV-4, 14-7
Programming example 8-23
Switch closure
Counting on Tipping Bucket
Rain Gage 8-5
Measuring 9-1
Switch Closure Input Module, see SDM-SW8A
Switching power to a device 14-7
Synchronous, Definition A-3
Synchronous Device Communication (SDC) 6-4
System memory OV-5, 1-7
System status (
∗B Mode) 1-9
T
Tables, List of LT-1
see also Program Tables
TC, see Thermocouples
TCOM OV-11, OV-13, 1-10, 6-8, 12-7, G-3
TD (Transmitted Data) 6-6
TDR, see SDM-TDR
TELCOM 12-7, G-6
Telecommunication 5-1
Automatic setting of baud rate 5-1
Automatic time-out from 5-2
Commands 5-3
Key definitions OV-11
Password/Security 5-4
Remote keyboard OV-11, 5-4
Telecommunication states 5-4
with Binary responses C-1
Telecommunications Command OV-11
Telecommunications (Modem) Pointer (MPTR) 2-2
Temp (107), see 107 Thermistor Probe -
[Instruction 11]
Temp, Module, see Internal Temperature -
[Instruction 17]
Temp RTD, see Temperature from Platinum
R.T.D. - [Instruction 16]
Temp TC DIFF, see Thermocouple Temperature
Measurement - [Instruction 14]
Temp TC SE, see Thermocouple Temperature
Measurement - [Instruction 13]
Temperature from Platinum R.T.D. -
[Instruction 16] 9-8
Programming examples 7-8, 7-9, 7-11, 8-13
Temperature from thermocouples, see
Thermocouple temperature
Temperature of Module, see Internal
Temperature - [Instruction 17]
Temperature range, CR10X 14-1
Terminal emulator OV-11
TGT1 Telonics GOES - [Instruction 120] 12-10
Thermocouple Measurements 13-12
Thermocouple Temperature Measurement
Differential - [Instruction 14] 9-8
Programming example 7-4
Single-Ended Measurement -
[Instruction 13] 9-7
Technique/error analysis 13-13
Using an External Reference Junction 7-4
Three Wire Half Bridge - [Instruction 7] 9-5,
13-18, 13-19, 13-20
Programming example 7-9
Throughput rate, Definition 1-1, A-3
Time - [Instruction 18] 9-9
Programming example 12-4
Time
Execution time requirements for instructions 3-6
Real Time, see Record Real Time -
[Instruction 77]
Setting/displaying ( ∗5 Mode) 1-4
Standard Deviation in Time - [Instruction 82]
11-8
Storing in Final Storage 11-4
Timer - [Instruction 26] 9-14
Timer, see SDM-INT8 8 Channel Interval