Campbell Scientific CR10X Measurement and Control System - Manual (Page 353)

INDEX-1
CR10X INDEX
∗ Modes, see Modes
1/X - [Instruction 42] 10-2
3 Wire Half Bridge - [Instruction 7] 9-5, 13-18,
13-19, 13-20
Programming Example 7-9
3WHB10K - 10 K ohm 3-Wire Half Bridge
Module 7-9
4 Wire Full Bridge, see Full Bridge with Single
Diff. Measurement - [Instruction 6]
4WPB100 - 100 ohm 4-Wire PRT Bridge
Module 7-8
5th Order Polynomial - [Instruction 55] 10-5
Programming examples 7-15, 7-16, 7-19,
8-21
5V Outputs OV-4
9-Pin Serial Port 6-1
12V terminals OV-4
37-Pin port description D-1
100 ohm PRT
3 wire half bridge 7-9
4 wire half bridge 7-7
4 wire full bridge 7-10
101 Thermistor Probe
Programming example 7-15
107 Thermistor Probe - [Instruction 11] 9-6
Programming examples 7-5, 8-4, 8-6
207 Relative Humidity Probe - [Instruction 12] 9-7
Programming example 7-5
223 Gypsum Soil Moisture Blocks 8-3
227 Gypsum Soil Moisture Block 7-14
A
A*X + B, see Scaling Array with Multiplier and
Offset - [Instruction 53]
A6REL-12/A21REL-12 Relay Driver 14-7
ABS(X) - [Instruction 43] 10-3
AC Excitation Measurements 13-21
AC Half Bridge - [Instruction 5] 9-4, 13-19,
13-21
Programming examples 7-15, 8-4
AC/DC Relay Controller, see SDM-CD16AC
Activate Serial Data Output - [Instruction 96]
4-1, 12-6
Interrupts during 6-3
Programming examples OV-16, 8-9
Using Storage Module with 4-5
Alkaline power supply 14-2
AM25T Solid State Thermocouple Multiplier 7-5
Programming example 8-11
AM416 Multiplexer 8-3
Analog ground definition OV-4
Analog inputs OV-4
Analog output, see SDM-AO4
Analog to Digital (A/D) conversion 13-1
AND construction, Logical 3-5
Anemometer (Photochopper output)
Programming example 7-6
AO4 Analog Output, see SDM-AO4
ARCTAN (X/Y) - [Instruction 66] 10-16
ARGOS - [Instruction 121] 12-10
Array ID
and Output Interval 2-2
Calculating data points 4-3
Definition A-2
Setting ID 2-2, 11-6
ASCII
Characters E-1
Definition A-1
Output formats 4-3, 4-4
Program transfer to computer/printer 1-11
Table E-1
Terminal or computer with terminal emulator OV-11
Transmission 6-7
ASPTC Aspirated Thermocouples 8-22
Asynchronous, Definition A-1
Automatic calibration sequence 13-22
Average - [Instruction 71] 11-4
Programming examples OV-16, 8-2
Average, Computing running 8-1
AVW1/AVW4 Vibrating Wire Interface 7-16
B
BATT VOLT, see Battery Voltage - [Instruction 10]
Battery Power 14-2
Battery Voltage - [Instruction 10] 9-6
Baud rate
Definition 6-7, A-1
Begin Case Statement - [Instruction 93] 12-5
Beginning of Loop, see Loop - [Instruction 87]
Binary telecommunications C-1
Generation of signature C-5
Block Move - [Instruction 54] 10-5
Programming examples 8-1, 8-2, 8-6, 8-13
BPALK Alkaline Power Supply 14-2
Bridge measurements 13-17
3 Wire Half Bridge 100 ohm PRT 7-9
4 Wire Full Bridge (Pressure Transducer)
7-11
4 Wire Full Bridge 100 ohm PRT 7-10
4 Wire Half Bridge 100 ohm PRT 7-7