Campbell Scientific CR10X Measurement and Control System - Manual (Page 358)

CR10X INDEX
INDEX-6
∗8 Manually initiated Data Output 4-3
Interrupts during 6-3
Output device codes for 4-2
∗9 Commands to Storage Module 4-6
∗A Internal Memory Allocation 1-5
∗B Memory Test and System Status 1-9
∗C Security 1-10
∗D, Save/Load Program 1-10, C-6
Modem/terminal
Computer requirements 6-5
Definition A-2
Peripherals 6-2
Modem Enable line on CR10X 4-1, 6-1
Peripheral requirements 6-4
Troubleshooting, Connecting to CR10X 6-7
Modem Pointer (MPTR) 2-2, 5-3
Modulo divide - [Instruction 46] 10-3
Move Signature into Input Location -
[Instruction 19] 9-10
Move Time to Input Location -
[Instruction 18] 9-9
MPTR 2-2, 5-3
MSX10/MSX20 Solar Panels 14-5
Multiply
X*F - [Instruction 37] 10-2
X*Y - [Instruction 36] 10-2
N
Natural logarithm - [Instruction 40] 10-2
Negative numbers 3-1
Nesting 3-5
Noise
Common sources 13-1
Modem 5-2, 6-4
Rejection 3-2
Non-integer portion, Extracting -[Instruction 44]
10-3
Nonlinear thermistor, Connecting to CR10X 7-15
O
On-line data transfer 4-1, 12-6, A-2
Operating details ix
Operating System (OS) Signature 1-9
OR construction, Logical 3-5
Output Array
and Output Interval A-2
Calculating data points per 4-3
Definition A-2
Setting ID 2-2
Output device codes
for
∗8 Mode 4-2
for Instruction 96 4-2, 12-7
Output Flag
Description 3-3
Example of setting OV-13
Setting to interval < 1 minute 8-5
Output interval OV-8, A-2
Output Processing Instructions 3-2, 11-1
Definition OV-8, A-2
Memory and execution times 3-7
Overrange detection 3-2
Overrun errors 1-1, 1-9
Overrun execution 1-1
P
Parameter
Data types 3-1
Definition A-2
Parameter entry table
∗4 1-2
Parameter Extension - [Instruction 63] 10-14
Programming example G-2, H-3
Parity, Checking 6-7
Paroscientific “T” series processing [Instruction
64] 10-14
Programming example 7-23
PC208 Datalogger Support Software OV-10,
OV-13, 4-3, 5-1, 5-5, G-2, I-1
PC208E OV-1, OV-11, OV-13, 1-10, 6-8, 12-7, G-6
Period Measurement - [Instruction 27] 9-15
Programming example 7-22
Peripherals
Current drain for common 14-2
Enabling/Addressing 6-2
General 4-1
Physical description, CR10X OV-1
Polynomial, see 5th Order Polynomial -
[Instruction 55]
Port, CR10X 37 pin description D-1
Serial Input/Output 9-pin 6-1
Port Read - [Instruction 25] 9-14
Port Serial I/O - [Instruction 15] B-1
Port Set - [Instruction 20] 9-10
Programming example 8-13
Port with Duration, see Pulse Port with Duration -
[Instruction 21]
Ports, see Control/Logic ports
Power ground OV-3, OV-4, 14-6
Power, Raising to Y - [Instruction 47] 10-3
Power requirements OV5, 14-1
Power supplies 14-2
Connecting directly to Wiring Panel 14-5
Connecting to CR10X OV-3, OV-5
Powerup Options, Setting 1-12
PPTR 2-2