AMX Modero NXD-CV5 - Manual (Page 113)

Programming
101 NXD-CV5 5" Modero Wall/Flush Mount Touch Panel
"^" Button Commands (Cont.)
^BOS
Set the button to
display either a
Video or
Non-Video
window.
Syntax:
"'^BOS-,,'"Variable: variable text address range = 1 - 4000.
button states range = 1 - 256 for multi-state buttons (0 = All states, for General buttons
1 = Off state and 2 = On state).
video state = Video Off = 0 and Video On = 1.Example:SEND_COMMAND Panel,"'^BOS-500,1,1'"Sets the button to display video.^BPPSet or clear the
protected page flip
flag of a button.Zero clears the flag.
Syntax: "'^BPP-,'"Variable: variable text address range = 1 - 4000.
protected page flip flag value range = 0 - 4 (0 clears the flag).Example:SEND_COMMAND Panel,"'^BPP-500,1'"Sets the button to protected page flip flag 1 (sets it to password 1).^BRDSet the border of
a button state/
states.Only if the specified border is not the same as the current border. The border names are
available through the TPDesign4 border-name drop-down list.
Syntax: "'^BRD-,,'"Variable: variable text address range = 1 - 4000.
button states range = 1 - 256 for multi-state buttons (0 = All states, for General buttons
1 = Off state and 2 = On state).
border name = Refer toBorder Styles and Programming Numbers table on page 91.Example:SEND_COMMAND Panel,"'^BRD-500.504&510.515,1&2,Quad Line'"Sets the border by name (Quad Line) to those buttons with the variable text range of
500-504 & 510-515.
Refer to theTPD4 Border Styles by Name table on page 91.^BSFSet the focus to
the text area. Note: Select one button at a time (single variable text address). Do not assign a variable
text address range to set focus to multiple buttons. Only one variable text address can be
in focus at a time.
Syntax: "'^BSF-,'"Variable: variable text address range = 1 - 4000.
selection value = Unselect = 0 and select = 1.Example:SEND_COMMAND Panel,"'^BSF-500,1'"Sets the focus to the text area of the button. ^BSMSubmit text for
text area buttons.This command causes the text areas to send their text as strings to the NetLinx Master.
Syntax: "'^BSM-'"Variable: variable text address range = 1 - 4000.Example:SEND_COMMAND Panel,"'^BSM-500'"Submits the text of the text area button.
Variable:
variable text address range = 1 - 4000.
button states range = 1 - 256 for multi-state buttons (0 = All states, for General buttons
1 = Off state and 2 = On state).
video state = Video Off = 0 and Video On = 1.
Example:
SEND_COMMAND Panel,"'^BOS-500,1,1'"
Sets the button to display video.
^BPP
Set or clear the
protected page flip
flag of a button.
Zero clears the flag.
Syntax:
"'^BPP-,'"
Variable:
variable text address range = 1 - 4000.
protected page flip flag value range = 0 - 4 (0 clears the flag).
Example:
SEND_COMMAND Panel,"'^BPP-500,1'"
Sets the button to protected page flip flag 1 (sets it to password 1).
^BRD
Set the border of
a button state/
states.
Only if the specified border is not the same as the current border. The border names are
available through the TPDesign4 border-name drop-down list.
Syntax:
"'^BRD-,
Variable:
variable text address range = 1 - 4000.
button states range = 1 - 256 for multi-state buttons (0 = All states, for General buttons
1 = Off state and 2 = On state).
border name = Refer toBorder Styles and Programming Numbers table on page 91.
Example:
SEND_COMMAND Panel,"'^BRD-500.504&510.515,1&2,Quad Line'"
Sets the border by name (Quad Line) to those buttons with the variable text range of
500-504 & 510-515.
Refer to theTPD4 Border Styles by Name table on page 91.
^BSF
Set the focus to
the text area.
Note: Select one button at a time (single variable text address). Do not assign a variable
text address range to set focus to multiple buttons. Only one variable text address can be
in focus at a time.
Syntax:
"'^BSF-,'"
Variable:
variable text address range = 1 - 4000.
selection value = Unselect = 0 and select = 1.
Example:
SEND_COMMAND Panel,"'^BSF-500,1'"
Sets the focus to the text area of the button.
^BSM
Submit text for
text area buttons.
This command causes the text areas to send their text as strings to the NetLinx Master.
Syntax:
"'^BSM-'"
Variable:
variable text address range = 1 - 4000.
Example:
SEND_COMMAND Panel,"'^BSM-500'"
Submits the text of the text area button.