KROHNE OPTISONIC 6300 EN - Manual (Page 89)

OPERATION
6
89
OPTISONIC 6300
www.krohne.com 07/2009 - 4000263902 - HB OPTISONIC 6300 R03 en
C5.2.12 threshold inactive if C5.2.11 is set to off: set
lag value between normal and
extended range
min-max: 05.0 - 80.0
C5.2.13 information serial number of circuit board,
software version, calibration date
of circuit board
C5.2.14 simulation A simulation of current output A set value:on/off, cancel min-max: 00.0 - 22.0
mA
C5.2.15 4 mA trimming restore factory setting for 4 mA min-max: 3.6000 - 5.5000 mA
C5.2.16 20 mA trimming restore factory setting for 20 mA min-max: 18.500 - 21.500 mA
C5.3 C5.3 C5.3 C5.3 frequency output frequency output frequency output frequency output
C5.3.1 pulse shape set shape symmetric, automatic, fixed
C5.3.2 pulse width active if C2.3.1 is set to fixed: set
time for pulse activation
min-max: 0000.05 - 2000.00
C5.3.3 100 % pulse rate min-max: 00000.0 - 10000.0
C5.3.4 measurement measurement value to frequency
output
(depends on pipe configuration: 1 or 2 pipes)
volume flow, mass flow, VoS, flow speed, gain,
SNR, diagnosis value, volume flow 1 or 2, VoS 1
or 2
C5.3.5 range set measurement range from 0
to 100 %
(min-max depends on parameter settings)
C5.3.6 polarity set polarity of frequency output both polarities
C5.3.7 limitation set lower and upper limit for
frequency output
min-max: -150 - +150 %
C5.3.8 low flow cutoff set low values to zero min-max: 00.0 - 20.0
C5.3.9 time constant within set time, measurements
are averaged, displayed and sent
to current output
min-max: 000.1 - 100.0
C5.3.10 invert signal define frequency output
activation
off: activate high current/switch closed
on: low current/switch open
C5.3.11 phase shift phase shift between output B and
D
0, 90, 180 degrees
C5.3.12 special function for ranging off, phase shift
C5.3.13 information
C5.3.14 simulation simulation of frequency output on, off, cancel
C5.4 C5.4 C5.4 C5.4 pulse output pulse output pulse output pulse output
C5.4.1 pulse shape set shape symmetric, automatic, fixed
C5.4.2 pulse width set time for pulse activation available if pulse shape is set: fixed min-max:
0000.05 - 2000.00
C5.4.3 max. pulse rate min-max: 00000.0 - 10000.0 Hz
C5.4.4 measurement measurement value to pulse
output
(depends on pipe configuration: 1 or 2 pipes)
volume flow, mass flow, volume flow 1 or 2
C5.4.5 pulse value unit unit for pulse output mL, L, free unit
C5.4.6 value p. pulse value of pulse per volume or
mass for pulse output
no min-max
C5.4.7 polarity set polarity of pulse output positive -, negative -, both polarity(ies), absolute
value
C5.4.8 low flow cutoff set low values to zero min-max: 00.0 - 20.0
C5.4.9 time constant within set time, measurements
are averaged, displayed and sent
to current output
min-max: 000.1 - 100.0
C5.4.10 invert signal activate switch closed, open off, on
.book Page 89 Tuesday, August 18, 2009 4:51 PM