Operation – KROHNE OPTISONIC 6300 EN User Manual
Page 88
6
OPERATION
88
OPTISONIC 6300
www.krohne.com
07/2009 - 4000263902 - HB OPTISONIC 6300 R03 en
C1.7.1
limitation
set lower and upper limit for flow
speed on all outputs
min-max: -100 - +100 m/s
C1.7.2
flow direction
select flow direction
normal, reverse
C1.7.3
time constant
within set time, measurements
are averaged, displayed and sent
to current output
min-max: 000.0 - 100.0 s
C1.7.4
low flow cutoff
beneath set flow speed, zero
appears in display
min-max: 0.000 - 10.00 m/s / 0.000 - 32.81 ft/s
C1.8.2
vel. of sound
simulation of the VoS
min-max: 0.0000 - 2500.0 m/s / 0.0000 - 8202.1
ft/s
C1.9.1
error limit
with set limits, every erroneous
measurement is counted as
percentage of the measured
values
min-max: 000 - 100 %
C1.9.2
counter decrease
amount with which the counter
decreases
min-max: 00 - 99
C1.9.3
counter limit
totalized correct measurements
equal to set counter decrease,
decrease error limit by 1
min-max: 000 - 999
C1.11
diagnosis value
diagnosis of the flow
measurement
signal quality, Reynolds number
C5.1
C5.1
C5.1
C5.1
I/O Hardware
I/O Hardware
I/O Hardware
I/O Hardware
C5.1.1
terminals A
assign terminal A
for basic I/O: current output, off
for Modular I/O: free selectable 1st IO Module
C5.1.2
terminals B
assign terminal B
for basic I/O: status output, limit switch, control
input
for Modular I/O: free selectable 2nd IO Module
C5.1.3
terminals C
assign terminal C
for basic I/O: status output, limit switch, off
for Modular I/O: fixed current out
C5.1.4
terminals D
assign terminal D
for basic I/O: status output, limit switch, pulse
output, frequency output, off
for Modular I/O: fixed current out
C5.2
C5.2
C5.2
C5.2
current out A
current out A
current out A
current out A
C5.2.1
range 0-100%
set current range
min-max: 04.0 - 20.0 mA
C5.2.2
extended range
set upper current range to
extended value
min-max: 03.5 - 21.5 mA
C5.2.3
error current
after error this selected current
is set
min-max: 03.0 - 22.0 mA
C5.2.4
error condition
error in device, out of specification, application
error
C5.2.5
measurement
measurement value to current
output
(depends on pipe configuration: 1 or 2)
volume flow, mass flow, VoS, flow speed, gain,
SNR, diagnosis value, volume flow 1 or 2, VoS 1
or 2
C5.2.6
range
set measurement range from 0
to 100 %
(min-max depends on parameter settings)
C5.2.7
polarity
set polarity of current output
positive -, negative -, both polarity(ies), absolute
value
C5.2.8
limitation
set lower and upper limit for
current output
min-max: -150 - +150 %
C5.2.9
low flow cutoff
beneath set value, current output
is set to zero
min-max: 00.0 - 20.0
C5.2.10
time constant
within set time, measurements
are averaged, displayed and sent
to current output
min-max: 000.1 - 100.0
C5.2.11
special functions
for ranging
automatic range, external range, off
.book Page 88 Tuesday, August 18, 2009 4:51 PM