HP E1418A - Manual (Page 178)

constants, reloading, 68
control register, 119, 129
current mode, 71
current process, 73–74
equipment required, 155
example program, 162–164
interruption, 74–75
isolation status register, 146
memory, 155
resistor value registers, 144
resistor, internal, 68, 70, 144, 159
test condition, 69
voltage mode, 72
voltage path, querying, 77
voltage path, setting, 76
voltage process, 74–75
CALibration Subsystem, 66–75
CAL:CONDition?, 67
CAL:CONFigure:RESistance?, 68, 159
CAL:RESet, 68
CAL:STORe, 69, 162
CAL:TEST?, 69
CAL:VALue:RESistance, 70, 159
CALn:CONFigure:CURRent?, 71, 160
CALn:CONFigure:VOLTage?, 72, 157
CALn:VALue:CURRent?, 73–74, 160–161
CALn:VALue:VOLTage?, 74–75, 157
Card
configuration register, 130
control register, 137
Certification, 7
CHAN
current calibration connections, 161
voltage calibration connections, 158
Changing
channel output modes, 46
configuration, 167
output mode, 51, 78
output value, 51
trigger state, 80
Channel
calibration path, querying, 77
calibration path, setting, 76
calibration process, 73–75
calibration readiness, 71–72
See also Channels
current gain calibration registers, 143
current mode calibration, 71, 73–74
current offset calibration registers, 142
current output connections, 33
current output connections, combining, 34
current output connections, querying, 86, 88
current output connections, specifying, 64, 85, 87
current output mode, 13, 45, 89, 136
gain value, 139
isolated output, 14–15
isolated plug-on module, 15, 17
mode change, 46
mode register, 119, 136
non-isolated output, 14–15
non-isolated plug-on module, 17
output lines, 33
output mode, changing, 46, 51, 78
output mode, configuring, 89
output mode, querying, 90
output mode, setting, 45
output relay, 53, 78, 82–83
output, setting, 50
program jumper register, 119, 134
relay control register, 119, 136
trigger register, 119, 135
trigger status report, 135
triggering, 104
voltage gain calibration registers, 141
voltage mode calibration, 72, 74–75
voltage offset calibration registers, 140
voltage output connections, 33
voltage output connections, combining, 34
voltage output connections, querying, 92, 94
voltage output connections, specifying, 65, 91, 93
voltage output mode, 13, 45, 89, 136
Channels
adding 8, 168–170
calibration condition, 69
See also Channel
combining, 34, 57
isolation status, 146
parallel connections, 34
series connections, 34
Checking
configuration, 166
errors, 47
SCPI errors, 47–49
Closing
output relay, 45, 53, 78, 82
*CLS, 96–100, 106
Combining Channels, 34, 57
Command Module
A16 address space, 114
A16 address space inside, 117
A16 address space outside, 117
Command Reference, 59–110
ABORt subsystem, 63
APPLy subsystem, 64–65
CALibration subsystem, 66–75
*CLS, 96–100, 106
177 HP E1418A User’s Manual
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com