HEIDENHAIN CNC Pilot 4290 - Manual (Page 458)

VIII
Index
Index
G
G303-Geo Circular slot on front face ..... 99
G304-Geo Full circle on front face ..... 99
G305-Geo Rectangle on front face ..... 100
G307-Geo Polygon on front face ..... 100
G308-Geo Start of pocket/island ..... 95
G309-Geo End of pocket/island ..... 96
G310-Geo Hole on lateral surface ..... 103
G311-Geo Linear slot on lateral surface ..... 104
G312—Geo Circular slot on lateral surface ..... 104
G313-Geo Circular slot on lateral surface ..... 104
G314-Geo Full circle on lateral surface ..... 105
G315-Geo Rectangle on lateral surface ..... 105
G317-Geo Polygon on lateral surface ..... 105
G34-Geo Thread (standard) ..... 90
G37-Geo Thread (general) ..... 90
G38-Geo Feed rate reduction ..... 93
G39-Geo Attributes for overlay elements ..... 94
G3-Geo Circular arc ..... 85
G401-Geo Linear pattern on front face ..... 100
G402-Geo Circular pattern on front face ..... 101
G411-Geo Linear pattern on lateral surface ..... 106
G412-Geo Circular pattern on lateral surface ..... 106
G49-Geo Bore hole (centric) ..... 91
G7-Geo Precision stop on ..... 92
G95-Geo Feed per revolution ..... 94
G9-Geo Precision stop blockwise ..... 92
G functions for machining
G0 Rapid traverse ..... 110
G1 Linear movement ..... 111
G100 Rapid traverse, front face/rear side ..... 149
G101 Linear, front face/rear side ..... 149
G102 Arc, front face/rear side ..... 149
G103 Arc, front face/rear side ..... 149
G110 Rapid traverse, lateral surface ..... 150
G111 Linear, lateral surface ..... 151
G112 Circular, lateral surface ..... 151
G113 Circular, lateral surface ..... 151
G119 Select C axis ..... 148
G12 Circular movement ..... 112
G120 Reference diameter ..... 148
G121 Mirror and shift contour ..... 117
G13 Circular movement ..... 112
G14 Tool change position ..... 110
G147 Safety clearance (milling cycles) ..... 119
G148 Changing the cutter compensation ..... 120
G149 Additive compensation ..... 120
G15 Rotary axis traverse ..... 168
G150 Compensate right tool tip ..... 121
G151 Compensate left tool tip ..... 121
G152 Zero point shift, C axis ..... 148
G153 Standardize C axis ..... 148
G162 Set synchronous mark ..... 160
G192 per-minute feed, rotary axes ..... 113
G2 Circular movement ..... 112
G204 Waiting for time ..... 170
G26 Spindle speed limit ..... 113
G3 Circular movement ..... 112
G30 Convert and mirror ..... 169
G31 Thread cycle ..... 140
G32 Simple thread cycle ..... 141
G33 Thread, single path ..... 142
G36 Tapping ..... 146
G4 Dwell time ..... 168
G40 Switch off TRC/MCRC ..... 115
G41 Switch on TRC/MCRC ..... 115
G42 Switch on TRC/MCRC ..... 115
G47 Safety clearance ..... 118
G48 Acceleration (slope) ..... 113
G50 Switch off oversize ..... 118
G51 Zero point displacement ..... 116
G52 Switch off oversize ..... 119
G53 Parameter-dependent zero-point shift ..... 116
G54 Parameter-dependent zero-point shift ..... 116
G55 Parameter-dependent zero-point shift ..... 116
G56 Zero-point shift, additive ..... 117
G57 Oversize, paraxial ..... 119
G58 Oversize, contour-parallel ..... 119