Aiwa XR-H330MD - Manual (Page 16)

TAPE RECORDING
This section explains how to record from a tape, the tuner, CD
player, MD player or external equipment.
Preparation
Use Type I (normal) tapes only.
4 Press • TAPE REC/REC MUTE to start recording.
When the selected function Is CD or MD, playback and
recording start simultaneously.
To record from a connected source, begin the playback of
that source.
To stop recording, press ■.
When recording from a CD or an MD, press ■ again to stop
playback of a CD or an MD.
To pause recording, press II. (Applicable when the source Is
TUNER or AUX/D-IN.) To resume recording, press again.
Sound adjustment during recording
The output volume and tone of the speakers or headphones may
be freely varied without affecting the recording.
Setting of T-BASS, graphic equalizer or Q SURROUND has no
effect on recording.
To record desired tracks of a CD or an MD
Select tracks to be recorded by programmed play (page 13,15),
and start recording.
In this case, set the blank skip play function to OFF (page 12).
1 Insert the tape to be recorded on into deck 2.
Insert the tape with the side to be recorded on facing out
from the unit.
• Set the tape to the point where recording will start with
or and stop the tape with ■.
Select the reverse mode using MODE, ENTER and
MULTI JOG (page 10).
To record on one side only, select "T".
To record on both sides, select "T3” or
When recording from a tape, the reverse mode Is automatically
set to " Z " . Note that recording will be done on one side of the
tape only.
• When reoording from the rear of the tape, the tape stops at
the end of recording of the rear side, even if the reverse
mode is set to " Z T or " C Z y .
Press one of the function buttons and prepare
the source to be recorded.
To record from a tape, insert the tape into deck 1, and press
TAPE DECK 1/2 to display "TPI”. Set the tape to the point
where recording will start with ◄►, ◄◄ or ►>-, and stop
the tape with ■.
To record from a CD, pross CD and load the CD(s). Then,
select a track to be recorded first with ◄◄, ►► or MULTI
JOG.
To record from an MD, press MD and insert an MD. Then,
select a track to be recorded first with ◄◄, ►► or MULTI
JOG.
To record from a radio broadcast, press TUNER BAND and
tune in to a station.
To record from a connected source;
• To record from a source equipment connected to DIGITAL
IN jacks on the rear, press AUX/D-IN repeatedly until "D-IN"
appears on the display. (The recording is not made in digital.)
• To record from a source equipment connected to VIDEO/
AUX jacks on the rear, press AUX/D-IN repeatedly until
"AUX” appears on the display.
INSERTING BLANK SPACES
4-second blank spaces can be inserted at the desired point during
recording. (Applicable when the source is TUNER or AUX/D-IN.)
1 Press • TAPE REC/REC MUTE during recording or while
in recording pause mode.
'hfetdJsrgil" on the display flashes for 4 seconds and the
tape runs without recording. After 4 seconds, the deck enters
the recording pause mode.
2 Press II to resume recording.
To insert a blank space of less than 4 seconds, press #
TAPE REC/REC MUTE again while
is flashing.
To insert blank spaces of more than 4 seconds, after the deck
enters recording pause mode, press • TAPE REC/REC MUTE
again. Each time the button is pressed, a 4-second blank space
is added.
TO ERASE RECORDING
1 Insert the tape to be erased in the deck 2.
2 Press TAPE to display "TP2" on the display window.
3 Set the tape to the point where erasing will start with
or and stop the tape with ■.
4 Press #TAPE REC/REC MUTE to start erasing.
1 6
ENGLISH