Aiwa XR-H330MD - Manual (Page 12)

CD PLAYING
DISC
DIRECT
PLAY
RANDOM/
REPEAT
■ CD EDIT/
CHECK
■ Numbered
buttons
■ SHIFT
To play one disc only, press DISC DIRECT PLAY 1-3.
The selected disc is played once.
To stop play, press ■.
To pause play, press
II. To resume play, press again.
To search for a particular point during piayback or in pause
mode, keep ◄◄ or ►► pressed and release it at the desired
point.
To skip to the beginning of a track, press ◄◄ or ►►
repeatedly or turn MULTI JOG until the desired track is displayed.
To remove discs, press — OPEN/CLOSE.
To Start play when the power Is off (Direct Play Function)
Press CD when the disc (s) is (are) loaded. The power is turned
on and play of the loaded disc(s) begins.
When A OPEN/CLOSE is pressed, the power is also turned on.
To check the remaining time
During CD piayback or in pause mode, press DISPLAY on the
unit or press CD EDIT/CHECK on the remote controi while
pressing SHIFT. The amount of time remaining untii all tracks
finish playing is displayed. To restore the elapsed playing time
display, repeat the above.
LOADING DISCS
Press CD, then press
±
OPEN/CLOSE to open the disc
compartment. Load disc(s) with the label side up.
To play one or two discs, place the discs on tray 1 and 2.
To play three discs, press DISC CHANGE to rotate the trays
after placing two discs. Place the third disc on tray 3.
Close the disc compartment by pressing £ OPEN/CLOSE.
Disc tray
number
Total number of tracks
Track number (displayed
up to the 20th track)
1 0 i v 5 3 : ; 3 i
Disc tray number
Selecting a track directly with the remote control
1 Press DISC DIRECT PLAY 1-3 to select a disc tray number.
2 Press numbered buttons 0-9, and +10 to select a track.
Example:
To select the 25th track, press +10 twice and 5.
To select the 10th track, press +10 and 0.
The selected track starts to play and playback continues to
the end of that disc.
Total playing time
If you press +10, press next numbered button within 4 seconds.
Replacing discs during play
While one diso is playing, the other discs can be replaced without
interrupting play.
1 Press DISC CHANGE.
2 Remove the discs and replace with other discs.
3 Press
± OPEN/CLOSE to close the disc compartment.
NOTE
• When loading an 8-cm (3-inch) disc, put it on the inner circle of
the tray.
• Do not place more than one compact disc on one disc tray.
• Do not tilt the unit with discs loaded. Doing so may cause
malfunctions.
• Do not use irregular shape CDs (example: heart-shaped,
octagonal ones). It may result in malfunctions.
PLAYING DISCS
Load discs.
To play all discs in the disc compartment, press
Play begins with the disc on tray 1.
Track number Track number being
being played played flashes.
t! •*“! \v::
;■ : ;; .• . : Wh'i
Disc tray number for
diso being played
Elapsed playing time of
the track being played
BLANK SKIP PLAY
The silent portions between the tracks recorded on a CD can be
skipped during playback.
• Blank skip play may not function with some CDs.
1 Press CD BLANK SKIP.
"CD BLANK SKIP ON" will flow from right to left in the display
window and small dot will appear in the display window.
Small dot
1 0 T : 5 8 : : 3 Í
1 2
ENGLISH