Rice Lake 520 HMI Digital Weight Indicator Installation Manual User Manual
Installation manual
Table of contents
Document Outline
- Contents
- About This Manual
- Safety
- 1.0 Introduction
- 1.1 Operating Modes
- 1.2 Front Panel Display
- 1.3 Indicator Operations
- 1.3.1 Toggle Gross/Net Mode
- 1.3.2 Toggle Units
- 1.3.3 Zero Scale
- 1.3.4 Acquire Tare
- 1.3.5 Remove Stored Tare Value
- 1.3.6 Keyed Tare
- 1.3.7 Print Ticket
- 1.3.8 Front Panel Setup
- 1.3.9 Display or Change Setpoint Value
- 1.3.10 Turn Setpoint On or Off
- 1.3.11 Display or Change Checkweigh Value
- 1.3.12 Set Date
- 1.3.13 Set Time
- 1.3.14 Display Accumulator
- 1.3.15 Count Display Mode
- 1.3.16 Peak Hold Mode
- 2.0 Installation
- 2.1 Unpacking and Assembly
- 2.1.1 Stainless Steel Panel Mount Model Parts Kit
- 2.1.2 Desktop Model Parts Kit
- 2.2 Panel Mount Installation
- 2.3 Enclosure Disassembly
- 2.4 Cable Connections
- 2.4.1 Load Cells
- 2.4.2 Panel Mount Parts Kit, PN 82427
- 2.4.3 Serial Communications
- 2.4.4 Condec UMC2000 Conversion Connections
- 2.4.5 Ethernet Communications
- 2.4.6 Digital I/O
- 2.5 Analog Output Card Installation
- 2.6 CPU Board Removal
- 2.7 Display Board Removal
- 2.8 Battery Replacement
- 2.9 Replacement Parts
- 2.10 Replacement Parts (Desktop Model Specific)
- 3.0 Configuration
- 3.1 Configuration Methods
- 3.1.1 Revolution Configuration
- 3.1.2 EDP Command Configuration
- 3.1.3 Front Panel Configuration
- 3.2 Menu Structures and Parameter Descriptions
- 3.2.1 Configuration Menu
- 3.2.2 Format Menu
- 3.2.3 Calibration Menu
- 3.2.4 Serial Menu
- 3.2.5 Program Menu
- 3.2.6 Print Format Menu
- 3.2.7 Setpoints Menu
- 3.2.8 Digital Input Menu
- 3.2.9 Analog Output Menu
- 3.2.10 Version Menu
- 4.0 Calibration
- 5.0 Using Revolution®
- 5.1 Installing and Starting the Program
- 5.1.1 To Install Revolution From Diskette
- 5.1.2 To Install Revolution by Downloading from the Web
- 5.2 Configuration
- 5.2.1 New Configuration File
- 5.2.2 Opening an Existing Configuration File
- 5.2.3 Saving a Configuration File
- 5.3 Downloading to the Indicator
- 5.4 Getting Data from Indicator
- 5.5 Revolution Help
- 6.0 Counting Operations
- 7.0 Checkweigh Mode
- 8.0 Peak Hold Mode
- 9.0 EDP Commands
- 10.0 Print Formatting
- 11.0 Setpoints
- 12.0 Appendix
- 12.1 Error Messages
- 12.1.1 Displayed Error Messages
- 12.2 Using the HARDWARE Command
- 12.3 Using the XE EDP Command
- 12.4 Status Messages
- 12.5 TARE and ZERO Key Functions
- 12.6 Data Formats
- 12.6.1 Continuous Output Serial Data Format
- 12.6.2 Demand Output Serial Data Format
- 12.6.3 RS-485 Data Formats
- 12.7 Custom Stream Formatting
- 12.8 Stream Formatting Examples
- 12.8.1 Toledo 8142 Indicator
- 12.8.2 Cardinal 738 Indicator
- 12.8.3 Weightronix WI 120 Indicator
- 12.9 ASCII Character Chart
- 12.10 Digital Filtering
- 12.10.1 DIGFLTx Parameters
- 12.10.2 RATTLETRAP® Filtering
- 12.10.3 DFSENS and DFTHRH Parameters
- 12.10.4 Setting the Digital Filter Parameters
- 12.11 Conversion Factors for Secondary Units
- 12.12 Analog Output Calibration
- 12.13 Test Mode
- 12.14 Specifications
- 520 Limited Warranty
- For More Information