Rice Lake 480 Legend Series Digital Weight Indicator Operator Card - Manual

Note
Note
MENU
UNITID
000000
TIMDAT
TIME
DATE
ACCUM
VIEW
TIME
DATE
PRINT
CLR Y
TARE
0
SERIAL SETPNT
See
SETPNT
Menu
AUDIT
CALIB
CNT
TIME
DATE
CONFIG
CNT
TIME
DATE
VERS
FIRMW
LR
PFRMAT
See
PFRMAT
Menu
MISC
POWER
AUTO
MANUAL
See
SERIAL
Menu
Note
Note
Warning
480 Digital Weight Indicator Operator Card
PN 152157 Rev B 02/2013
US 800-472-6703 International 715-234-9171
Refer to Manual (PN119201) for detailed instructions
Manuals are available on our web site at
http://www.ricelake.com/manuals.aspx
Electric shock hazard.
Only qualified service personnel should operate
the equipment.
Refer all repairs and modifications to a distributor or service
technician.
Failure to heed may result in serious injury or death.
Front Panel Display and Keypad
The indicator front panel has a seven segment, six digit LED
display with:
• six primary scale function keys
• power (ON/OFF) key
• eight LED lights
For complete description of indicator front panel see Opera-
tor’s Manual PN 119201.
PRINT
MENU
UNIT
POWER
TARE
GROSS
NET
B/N
ZERO
WEIGHING SYSTEMS
Figure 1. Indicator Front Panel
To Enter and Exit User Menu
(See Figure 2.)
1. Press MENU .
2. Press to AUDIT.
3. Press or to select the desired parameter.
4. Press to enter parameter; follow the instructions for
modifying that parameter.
5. When complete, press until MENU is displayed.
6. Press again to return to weighing mode.
To Edit a Numeric Value
Press or to select the digit.
Press or to increment or decrement the value.
Press TARE when the value is correct.
Indicator Operations
Zero Scale
1. In gross mode, remove all weight from the scale and wait
for the LED to light.
2. Press ZERO . The LED lights to indicate the scale is
zeroed.
Toggle Units
1. Press UNIT to toggle between primary and secondary
units. The current unit LED will be lit.
Acquire Tare
1. Place container on scale; wait for the LED to light.
2. Press TARE to acquire the tare weight of the container.
Net weight is displayed and the T LED lights to show the
tare value was entered.
Preset Tare (Keyed Tare)
1. With the scale empty and display showing zero weight,
press TARE .
2. Display will show (000000), the focused digit will flash.
3. To edit the value, see “To Edit a Numeric Value”.
4. The display will change to the Net mode and the PT LED
lights to show the preset tare was entered.
Display Tare
1. Enter USER MENU. See “To Enter and Exit User Menu”.
2. Navigate to
TARE
, then press .
3. Exit USER MENU. See “To Enter and Exit User Menu”.
If there is no tare in the system, the value displayed will
be zero and the Gross and Net LED will be turned off.
Figure 2. Menu Key User Menu
Print Ticket
1. Press PRINT to print either the Gross or Net format. Also,
when enabled and displayed it is used to print the
accumulator.
2. Wait for LED to light.
3. Press PRINT to send data to the serial port.
If LED is not lit, the PRINT key command is
executed if the scale comes out of motion within 3
seconds.
Toggle Gross/Net Mode
1. Press GROSS
NET
B/N
to switch the display mode between gross
and net. If a tare value has been entered or acquired, the
net value is the gross weight minus the tare.
• Gross mode – Gross/Brutto LED is lit.
• Net mode – Net LED is lit.
Display or Change Time & Date
To set the date and time:
1. Enter USER MENU. See “To Enter and Exit User Menu”.
2. Navigate to TIMDAT (TIME/DATE).
3. Press and select Time or Date with or .
4. Press to view the current setting.
5. To edit the value, see “To Edit a Numeric Value”.
6. Exit USER MENU. See “To Enter and Exit User Menu”.
Use the same procedure to enter the date in the same
format configured for the indicator: MMDDYY,
DDMMYY, YYMMDD or YYDDMM.
Display and Edit Setpoint Value
1. Enter USER MENU. See “To Enter and Exit User Menu”.
2. Navigate to
SETPNT , press .
3. Navigate across to desired setpoint number (1-8).
4. Press and navigate across to select User.
5. Press and navigate across to select Enable, Value,
PreAct or Hysteresis.
6. Press to view, enable or edit the value. (See “To Edit a
Numeric Value”)
7. Exit USER MENU. See “To Enter and Exit User Menu”.
Display Accumulator
1. Enter USER MENU. See “To Enter and Exit User Menu”.
2. Navigate to ACCUM, press .
3. Press or to select VIEW, TIME, DATE, PRINT or
CLR. Press .
4. For VIEW, TIME, DATE, press to return to ACCUM. 
For PRINT or CLEAR, press TARE to print or clear the
accumulator.
5. Exit USER MENU. See “To Enter and Exit User Menu”.