Yokogawa ADMAG CA - Manual (Page 87)

IM 1E8B0-01E
10-11
10. OUTLINE
᭹ Unless otherwise specified, difference in the dimensions are refer to the following table.
Above Equal or below Above Equal or below
Category of basic dimension Category of basic dimension
Tolerance Tolerance
3 (0.12)
6 (0.24)
10 (0.39)
18 (0.71)
30 (1.18)
50 (1.97)
80 (3.15)
120 (4.72)
180 (7.09)
250 (9.84)
315 (12.40)
400 (15.75)
3 (0.12)
6 (0.24)
10 (0.39)
18 (0.71)
30 (1.18)
50 (1.97)
80 (3.15)
120 (4.72)
180 (7.09)
250 (9.84)
315 (12.40)
400 (15.75)
500 (19.69)
Ϯ 0.7 ( Ϯ 0.03)
Ϯ 0.9 ( Ϯ 0.04)
Ϯ 1.1 ( Ϯ 0.04)
Ϯ 1.35 ( Ϯ 0.05)
Ϯ 1.65 ( Ϯ 0.06)
Ϯ 1.95 ( Ϯ 0.08)
Ϯ 2.3 ( Ϯ 0.09)
Ϯ 2.7 ( Ϯ 0.11)
Ϯ 3.15 ( Ϯ 0.12)
Ϯ 3.6 ( Ϯ 0.14)
Ϯ 4.05 ( Ϯ 0.16)
Ϯ 4.45 ( Ϯ 0.18)
Ϯ 4.85 ( Ϯ 0.19)
500 (19.69)
630 (24.80)
800 (31.50)
1000 (39.37)
1250 (49.21)
1600 (62.99)
2000 (78.74)
2500 (98.43)
630 (24.80)
800 (31.50)
1000 (39.37)
1250 (49.21)
1600 (62.99)
2000 (78.74)
2500 (98.43)
3150 (124.02)
Ϯ 5.5 ( Ϯ 2.17)
Ϯ 6.25 ( Ϯ 0.25)
Ϯ 7.0 ( Ϯ 0.28)
Ϯ 8.25 ( Ϯ 0.32)
Ϯ 9.75 ( Ϯ 0.38)
Ϯ 11.5 ( Ϯ 0.45)
Ϯ 14.0 ( Ϯ 0.55)
Ϯ 16.5 ( Ϯ 0.65)
Remarks: The numeric is based on criteria of tolerance class IT18 in JIS B 0401.
General tolerance in the dimensional outline drawing.
Unit : mm (approx.inch)
10.8 Earth Ring Inside Diameter
15 (0.5)
25 (1)
40 (1.5)
50 (2)
80 (3)
100 (4)
150 (6)
200 (8)
ш15 (0.6)
ш27 (1.1)
ш40 (1.6)
ш52 (2.1)
ш81 (3.2)
ш98 (3.9)
ш144 (5.7)
ш192 (7.6)
* Please be sure the inner diameter of a gasket
does not protrude to the earth ring inside diameter.
Unit : mm (inch)
EARTH RING
INSIDE DIAMETER
Size