FEC AFC1500 - Manual (Page 79)

AFC1500 Multi-2 Unit Hardware Manual (Rev2.1)
PAGE 5 - 35
Chapter 5: Control Interfaces
5.7.4 Ouput Signals (Word 01 ~ Word 16)
The Multi-2 Unit is capable of providing over 570 Output signals to indicate the status of the Multi-2
Unit and of all the AFC1500 SAN Controllers connected to it (up to 31 controllers).
See Section 4.7.3 for available output signals.
Since Modbus Plus sends I/O signals 8 bits at a time, and trying to use the data as a word, all
bits and bytes are transferred backwards.
Word No. Bit Signal
FEC Multi-2
Bank Bit
Output
Word
No.01
0bit Sequence Output 1 1 8
1bit Sequence Output 0 1 7
2bit End 1 6
3bit Busy 1 5
4bit Ready 1 4
5bit Abnormal 1 3
6bit Total Accept 1 2
7bit Total Reject 1 1
8bit Spindle No.1 BYP 1 16
9bit Spindle No.1 ABN. 1 15
10bit Spindle No.1 Reject 1 14
11bit Spindle No.1 Accept 1 13
12bit Current Warning 1 12
13bit Spindle in Bypass 1 11
14bit Sequence Output 3 1 10
15bit Sequence Output 2 1 9
Output
Word
No.02
0bit Spindle No.3 BYP 1 24
1bit Spindle No.3 ABN. 1 23
2bit Spindle No.3 Reject 1 22
3bit Spindle No.3 Accept 1 21
4bit Spindle No.2 BYP 1 20
5bit Spindle No.2 ABN. 1 19
6bit Spindle No.2 Reject 1 18
7bit Spindle No.2 Accept 1 17
8bit Spindle No.5 BYP 1 32
9bit Spindle No.5 ABN. 1 31
10bit Spindle No.5 Reject 1 30
11bit Spindle No.5 Accept 1 29
12bit Spindle No.4 BYP 1 28
13bit Spindle No.4 ABN. 1 27
14bit Spindle No.4 Reject 1 26
15bit Spindle No.4 Accept 1 25
Output
Word
No.03
0bit Spindle No.7 BYP 2 8
1bit Spindle No.7 ABN. 2 7
2bit Spindle No.7 Reject 2 6
3bit Spindle No.7 Accept 2 5
4bit Spindle No.6 BYP 2 4
5bit Spindle No.6 ABN. 2 3
6bit Spindle No.6 Reject 2 2
7bit Spindle No.6 Accept 2 1
8bit Spindle No.9 BYP 2 16
9bit Spindle No.9 ABN. 2 15
10bit Spindle No.9 Reject 2 14
11bit Spindle No.9 Accept 2 13
12bit Spindle No.8 BYP 2 12
13bit Spindle No.8 ABN. 2 11
14bit Spindle No.8 Reject 2 10
15bit Spindle No.8 Accept 2 9
：
CH. No. Bit Signal
Output CH.
No.16
0bit 8 1
…
15bit 8 32
These Output signals are user
configurable using the AFC User
Console Software and may be
programmed on any designated
bit.
The Output signal mapping
shown is only an EXAMPLE.
The signals may be programmed
for placement in ANY bit
position.