Technicolor - Thomson Wireless Business DSL Routers SpeedTouchTM620 User Manual
Speedtouch™620, Operator’s guide, Wireless business dsl routers
Table of contents
Document Outline
- Contents
- About this Operator’s Guide
- 1 Introduction
- 2 SpeedTouch™ Command Line Interface
- 3 SpeedTouch™ System Software
- 4 SpeedTouch™ Configuration Management
- Saving the configuration
- Backing up configurations
- Storing and restoring multiple configurations
- 4.1 Configuration Management via the SpeedTouch™ Web Interface
- 4.2 Configuration Management via Telnet
- 4.3 The :Config CLI Command Group
- 4.4 SpeedTouch™ Service Templates
- 4.5 SpeedTouch™ System Languages Management
- 5 SpeedTouch™ Software Modules
- 6 SpeedTouch™ System Services
- Overview
- 6.1 SpeedTouch™ Dynamic DNS
- Introduction
- Applying for the dynamic DNS service
- Dynamic DNS client configuration
- Preparing the SpeedTouch™ dynamic DNS client
- The SpeedTouch™ CLI dyndns commands
- Example dynamic DNS subscription
- Adding a dynamic DNS host name
- Adding a dynamic DNS client
- Modifying the dynamic DNS client
- Refining the dynamic DNS service settings
- Enabling the Dynamic DNS Service
- Checking dynamic DNS client Resolving
- The Dynamic DNS Web Page
- 6.2 The SpeedTouch™ SNTP Client
- 6.3 Website Filtering
- About Website Filtering
- Address Based Filtering
- Content Based Filtering
- Overview
- 6.3.1 The Website Filtering Configuration Pages
- 6.3.2 How to Verify the Filtering Configuration
- 6.3.3 How to Activate a Web Filtering License
- 6.3.4 Configuring the Actions for Uncategorised Sites
- 6.3.5 How to Create an Address Based Filter
- 6.3.6 How to Create a Content Based Filter
- 6.3.7 How to Create a Content Level
- 6.4 Intrusion Detection and Protection
- 6.5 Remote Assistance
- 7 The SpeedTouch™ File System
- 8 SpeedTouch™ Remote Access
- The SpeedTouch™ access methods
- Restrictions
- Access methods vs system services
- Configuration via CLI
- Remote Assistance
- Interface access list
- IPSec Protection
- 8.1 Remote Web Interface Access
- 8.2 Secure Remote Web Interface Access
- 8.3 Remote Telnet Access
- 8.4 Remote SSH Access
- 8.5 Remote FTP Access
- 8.6 Remote SFTP Access
- 8.7 LAN Based Auto-Configuration (LAC) Support (TR-064)
- 8.8 CPE WAN Management Protocol (CWMP) Support (TR-069)
- 9 The Integrated SpeedTouch™ ISDN Modem
- Overview
- 9.1 About the ISDN Modem
- 9.2 How to Configure the ISDN Modem
- 9.3 ISDN Backup
- 9.4 ISDN Callback
- 9.5 ISDN Remote CAPI
- 10 SpeedTouch™ Monitoring
- Overview
- 10.1 An Introduction to SNMP
- 10.2 SNMP configuration
- About SNMP configuration
- Enabling SNMP
- Command Line Interface (CLI)
- Overview
- 10.2.1 How to Allow Access to the SNMP Agent
- 10.2.2 How to View the SNMP Configuration
- 10.2.3 How to View the System Contact, Name and Location
- 10.2.4 How to Configure SNMPv1
- 10.2.5 How to Configure the System contact, Name and Location
- 10.2.6 How to Force the Source IP Address
- 10.2.7 How to Configure the SNMP Target
- 10.2.8 How to Read SNMP Parameters via the CLI
- 10.2.9 How to Allow Remote SNMP
- 10.2.10 How to Add an SNMP User
- 10.2.11 How to Restrict SNMP Access
- 10.2.12 How to Configure the Traps
- 10.3 The SpeedTouch™ Syslog
- 10.4 SpeedTouch™ Identification on AWS
- 11 SpeedTouch™ Advanced Diagnostics
- About the Advanced Diagnostics
- Overview
- 11.1 The Office Network Web Page
- 11.2 The Diagnostic Web Page
- 11.3 Command Line Interface Diagnostics
- 12 SLA Monitoring.
- 13 Resetting the SpeedTouch™
- Need more help?