Extron electronic Ultra Series - Manual (Page 125)

4-15 CrossPoint / MAV Matrix Switchers • Programmer’s Guide
Command/response table for SIS commands (continued)
Command ASCII command
(host to switcher)
Response
(switcher to host)
Additional
description
View ties, gain, volume, mutes, presets, and DSVP
N
X#
= Output number 01 – (maximum number of outputs for your model)
X@
= Input number (for tie) 00 – (maximum number of inputs for your model) (00 = untied)
X^
= Numeric dB value –18 to +24 (1 dB/step) (Default = 0 dB)
X*
= Volume adjustment range 0 – 64 (1 dB/step except for 0-to-1, which is 22 dB)
X1@
= Video/audio mute: 0 = no mutes
1 = video mute
2 = audio mute
3 = video and audio mute
X(
= Global or room preset # 00 - 32, 10 maximum for a room preset (00 = current configuration)
View RGBHV output tie X#
&
X@]
Example: 15& 27 ] Input 27 RGBHV is tied to
output 15.
View video output tie X# % X@]
Example: 7% 02
] Input 2 video is tied to output 7.
View audio output tie X# $ X@]
Example: 3$ 06
] Input 6 audio is tied to output 3.
View input gain or attenuation X@
G
X^]
Example: 4G -02
] Gain for input 4 is -2 dB.
View output volume X@
V
X*]
Example: 7V 55 ] Volume for output 7 is 55
steps (9 dB of attenuation,
86.5% of total volume).
View output mutes E VM } X1@ 1 X1@ 2 ...
X1@ n ] Each X1@ response is the
mute status of an output,
starting from output 1.
n
= the maximum number of
outputs for this model.
Example:
CrossPoint 450 Plus 3232 HVA
E
VM
}
Mut00001000000230000000000000000000
]
Output 5 video, output 12
audio, and output 13 video
and audio are muted. All
other outputs are unmuted.
N The “Mut” portion of the response appears only when the switcher is in Verbose mode 2 or 3. See the Verbose mode
command on page 4-23.
View video global preset
configuration EX(
*
X#
*1VC
} X@ n •
X@ n +1 •...•
X@
n + 15 •Vid
]
Show preset X( ’s video
configuration. Show
the input (
X@
) tied to 16
sequential outputs, starting
from output
X# .
Command description:
Response description: preset #*starting output # (StO#)*1(=video)VC
input # (I#) tied to StO#•I# tied to StO#+1•I# tied to StO+2• ... •I# tied to StO+15•Vid
]
N The starting output number (
X#
) should always be “1” for matrix sizes of 16 outputs or smaller.
N
EX(
*
X#
*1VC
}
where
X(
= 0 returns the switcher’s current video configuration.
Example:
MAV Plus 3232 E
4*17*1VC
}
17 Output:
Response = tied input:
input 24 tied to output 19
18 19 20 21 22 23 24 25 26 27 28
08•08•24•08•08•29•29•00•08•01•01•01•08•08•08•08•Vid
29 30 31 32
no tied input input 8 tied to output 29
Each position shown in the response is an output: left = starting output (17), right = starting output +15 (32). The
number in each position is the input tied to that output.
In this example, preset 4, video input 1 is tied to outputs 26 through 28; input 8 is tied to outputs 17, 18, 20, 21, 25, and
29 through 32; input 24 is tied to ouput 19; and input 29 is tied to outputs 22 and 23. No input is tied to output 24.