Yaskawa F7 to L1000A - Manual (Page 47)

(Header Title) Application Note
Doc#: PL.L1000A.01 Copyright Yaskawa Electric America, Inc. ©2010 www.yaskawa.com September 9, 2010 47 of 57
Subject: Transition Guide Product: L1000A Document: PL.L1000A.01
Title: Product Transition Guide – F7 to L1000A
Product Transition Guide – F7 to L1000A
F7 L1000A
Parameter Name
Parameter Default
Setting
Record
Parameter Default
Comments: Gray shading indicates default setting.
Stopping Method After
Communication Error
H5-04 3 H5-04 3
F7 L1000A
H5-04 H5-04
0: Ramp to stop
0: Ramp to stop
1: Coast to stop 1: Coast to stop
2: Fast Stop 2: Fast Stop
3: Continue operation 3: Continue operation
Communication Error
Detection Selection
H5-05 1 H5-05 1
F7 L1000A
H5-05 H5-05
0: Disabled
0: Disabled
1: Enabled 1: Enabled
Send Wait Time H5-06 5ms H5-06 5ms
RTS Control Selection H5-07 1 H5-07 1
F7 L1000A
H5-07 H5-07
0: Disabled
(RTS always on)
0: Disabled
(RTS always on)
1: Enabled
(RTS enabled during send
only) 1: Enabled
(RTS enabled during send
only)
CE Detection Time ─ ─ H5-09 2.0 s
Unit Selection for MEMOBUS
Register 0025H
H5-10 0 H5-10 0
F7 L1000A
H5-10 H5-10
0: 0.1 V units
0: 0.1 V units
1: 1 V units 1: 1 V units
MEMOBU
S C
ommunic
at
ion
Communications ENTER
Function Selection
─ ─ H5-11 0
L1000A
H5-11
0: Enter Cmd Req.
1: Enter Cmd Not Req.
Pulse Train Input Function
Selection
H6-01 0 ─ ─
Pulse Train Input Scaling H6-02 1440 Hz ─ ─
Pulse Train Input Gain H6-03 100.0% ─ ─
Pulse Train Input Bias H6-04 0.0% ─ ─
Pulse Train Input Filter Time H6-05 0.10 s ─ ─
No corresponding parameter in L1000A.
Pulse Train Monitor Selection H6-06 2 ─ ─ No corresponding parameter in L1000A.
P
ul
se T
ra
in I/
O
Pulse Train Monitor Scaling H6-07 1440 Hz ─ ─
Motor Overload Protection
Selection
L1-01 1 L1-01 1 *
F7 L1000A
L1-01 L1-01
0: Disabled
0: Disabled
1: General-purpose motor
protection 1: General-purpose motor
protection
2: Drive-dedicated motor
protection 2: Drive-dedicated motor
protection
3: Vector motor protection 3: Vector motor protection
─
5: PM motor protection
(constant torque)
*Determined by the control mode selected.
Motor Overload Protection
Time
L1-02 8.0min L1-02 1.0 min.
F7 L1000A
Setting Range
0.1 to 20.0 min
0.1 to 5.0 min
Motor Overheat Alarm
Operation Selection
L1-03 3 ─ ─
Motor Protection
Function
Motor Overheat Fault
Operation Selection
L1-04 1 ─ ─
No corresponding parameter in L1000A.