Yaskawa F7 to L1000A - Manual (Page 27)

(Header Title) Application Note
Doc#: PL.L1000A.01 Copyright Yaskawa Electric America, Inc. ©2010 www.yaskawa.com September 9, 2010 27 of 57
Subject: Transition Guide Product: L1000A Document: PL.L1000A.01
Title: Product Transition Guide – F7 to L1000A
Product Transition Guide – F7 to L1000A
F7 L1000A
Parameter Name
Parameter Default
Setting
Record
Parameter Default
Comments: Gray shading indicates default setting.
Timer Function On-Delay
Time
b4-01 0.0 s b4-01 0.0 s ─
Timers Timer Function Off-Delay
Time
b4-02 0.0 s b4-02 0.0 s ─
PID Cntrol Method Selection b5-01 0 ─ ─
Proportional Gain Setting (P) b5-02 1.00 ─ ─
Integral Time Setting (I) b5-03 1.0 s ─ ─
Integral Limit Setting b5-04 100.0% ─ ─
Derivative Time (D) b5-05 0.00 s ─ ─
PID Output Limit b5-06 100.0% ─ ─
PID Offset Tuning b5-07 0.0% ─ ─
PID Primary Delay Time b5-08 0.00 s ─ ─
PID Output Characteristics
Selection
b5-09 0 ─ ─
PID Output Gain Setting b5-10 1.0 ─ ─
PI
D Con
trol
PID Output Reverse Selection b5-11 0 ─ ─
No corresponding parameter in L1000A.
Selection of PID Feedback
Command Loss Detection
b5-12 0 ─ ─
PID Feedback Loss Detection
Level
b5-13 0% ─ ─
PID Feedback Loss Detection
Time
b5-14 1.0 s ─ ─
PID Sleep Function Start
Level
b5-15 0.0 Hz ─ ─
PID Sleep Delay Time b5-16 0.0 s ─ ─
PI
D Con
trol
PID Accel/Decel Time b5-17 0.0 s ─ ─
No corresponding parameter in L1000A.
Dwell Reference at Start b6-01 0.0 Hz b6-01* 0.0 %
F7 L1000A
Setting Range
0.0Hz to 400.0Hz
0.0% to 100.0%
Dwell Time at Start b6-02 0.0 s b6-02 0.0 s
Dwell Frequency at Stop b6-03 0.0 Hz b6-03* 0.0 %
Dwell Fun
ction
Dwell Time at Stop b6-04 0.0 s b6-04 0.0 s
─
Droop Control Gain b7-01 0.0% b7-01 0.0% ─
Droop Con
trol
Droop Control Delay Time b7-02 0.05 s b7-02 0.05 s ─
Energy Saving Control
Selection
b8-01 0 b8-01 0
F7 L1000A
b8-01 b8-01
0: Energy Saving disabled 0: Energy Saving disabled
1: Energy Saving enabled 1: Energy Saving enabled
Energy Saving Gain b8-02 0.7 ─ ─
Energy Saving Control Filter
Time Constant
b8-03 * ─ ─
Energy Saving Coefficient
Value
b8-04 * ─ ─
Power Detection Filter Time b8-05 20 ms ─ ─
No corresponding parameter in L1000A.
Energy Sa
ving
Con
trol
Energy Saving Control
Constant
(Ki)
─ ─ b8-16* 0.10 For IPM motors only