Verilink SCM (880-503300-001) Product Manual - Manual (Page 72)

Downloading and Broadcasting Firmware
6-8 Verilink SCM
Figure 6-4 Administration Menu
Select W) write file to flash to save the new file and select Yes to
write to flashbank B. This process takes about five minutes. As the
process completes, a message appears:
dnld_ramdisk: done
After another minute, the Administration Menu reappears. Select
Y) switch over once to try your new code. When asked which bank
to boot from, choose “B”.
Copying Bank B to
Bank A
Verilink suggests that you DO NOT use the Flash Copy command
unless specifically instructed to do so by a Tech Support
representative or an upgrade procedure included with new
firmware files. No harm is done if bank A and bank B contain
different versions of firmware. A failed attempt to copy bank B to
bank A could leave an SCM module unable to boot.
By keeping the original version of firmware intact in bank A, you
can easily recover if an upgraded firmware version is later found to
have a problem.
SCM CONTROLLER ADMINISTRATION MENU -- SCM CONTROLLER ADMINISTRATION MENU -- SCM CONTROLLER ADMINISTRATION MENU -- SCM CONTROLLER ADMINISTRATION MENU --
Date/Time/Zone: 8-26-98 21:25:20 PST Date/Time/Zone: 8-26-98 21:25:20 PST Date/Time/Zone: 8-26-98 21:25:20 PST Date/Time/Zone: 8-26-98 21:25:20 PST
Node address: [0.0.0.2]
Node address: [0.0.0.2] Node address: [0.0.0.2] Node address: [0.0.0.2]
Node id: 122
Node id: 122 Node id: 122 Node id: 122
Site name: SCM Tutorial
Site name: SCM Tutorial Site name: SCM Tutorial Site name: SCM Tutorial
System uptime: 18:10:19
System uptime: 18:10:19 System uptime: 18:10:19 System uptime: 18:10:19
--- NODE ADMINISTRATION --- --- NODE ADMINISTRATION --- --- NODE ADMINISTRATION --- --- NODE ADMINISTRATION ---
H) set shelf type Z) set time zone H) set shelf type Z) set time zone H) set shelf type Z) set time zone H) set shelf type Z) set time zone
T) set time D) set date
T) set time D) set date T) set time D) set date T) set time D) set date
B) download firmware Y) switch over once
B) download firmware Y) switch over once B) download firmware Y) switch over once B) download firmware Y) switch over once
W) write file to flash O) switch over permanent
W) write file to flash O) switch over permanent W) write file to flash O) switch over permanent W) write file to flash O) switch over permanent
C) set front/rear access Q) query firmware
C) set front/rear access Q) query firmware C) set front/rear access Q) query firmware C) set front/rear access Q) query firmware
A) set node address R) reset card
A) set node address R) reset card A) set node address R) reset card A) set node address R) reset card
I) change site name E) change node id
I) change site name E) change node id I) change site name E) change node id I) change site name E) change node id
N) TCP/IP parameters P) change password
N) TCP/IP parameters P) change password N) TCP/IP parameters P) change password N) TCP/IP parameters P) change password
M) modem parameters S) node selection
M) modem parameters S) node selection M) modem parameters S) node selection M) modem parameters S) node selection
X) exit this menu F) partition copy (B => A)
X) exit this menu F) partition copy (B => A) X) exit this menu F) partition copy (B => A) X) exit this menu F) partition copy (B => A)
K) show shelf sync_master
K) show shelf sync_master K) show shelf sync_master K) show shelf sync_master
A [0.0.0.2] [1,1] SCM > A [0.0.0.2] [1,1] SCM > A [0.0.0.2] [1,1] SCM > A [0.0.0.2] [1,1] SCM >