Verilink SCM (880-503300-001) Product Manual - Manual (Page 58)

Circuit Manager
5-4 Verilink SCM
Figure 5-2 Circuit Manager Menu
NOTE: When Circuit Manager is accessed, all other users are
prevented from using it. Anyone else who tries to enter the
menu while it is being accessed gets the message: “Wait until
later.”
The Circuit Manager Menu shown in Figure 5-2 already contains
six circuits in a table at the top of the menu. This means that
someone has already created these circuits. Five of the circuits are
reported Active, the other is Inactive. The commands on the
Circuit Manager Menu are described in
Table 5-2 .
Until circuits have been created, no circuits are listed in the table at
the top of the menu. Instead, the following message is displayed:
>>>>>> NO CIRCUIT FOUND IN DATABASE <<<<<
or
>>>>>> REACHED THE END OF THE LIST <<<<<
-- CIRCUIT MANAGER MENU [0,1] SCM Firmware 1.20 -- -- CIRCUIT MANAGER MENU [0,1] SCM Firmware 1.20 -- -- CIRCUIT MANAGER MENU [0,1] SCM Firmware 1.20 -- -- CIRCUIT MANAGER MENU [0,1] SCM Firmware 1.20 --
Page : 1 Page : 1 Page : 1 Page : 1
Total: 6 circuits
Total: 6 circuits Total: 6 circuits Total: 6 circuits
Name Type Mode Prio Source Port Dest Port Bus Status Name Type Mode Prio Source Port Dest Port Bus Status Name Type Mode Prio Source Port Dest Port Bus Status Name Type Mode Prio Source Port Dest Port Bus Status
------------ ---- ---- ---- ---------------- ---------------- --- ------
------------ ---- ---- ---- ---------------- ---------------- --- ------ ------------ ---- ---- ---- ---------------- ---------------- --- ------ ------------ ---- ---- ---- ---------------- ---------------- --- ------
c1 perm 64k norm [0,4] QUAD net1 [0,11] QUAD dat1 AUT Active
c1 perm 64k norm [0,4] QUAD net1 [0,11] QUAD dat1 AUT Active c1 perm 64k norm [0,4] QUAD net1 [0,11] QUAD dat1 AUT Active c1 perm 64k norm [0,4] QUAD net1 [0,11] QUAD dat1 AUT Active
c2 perm 64k norm [0,4] QUAD net2 [0,11] QUAD dat2 AUT Active
c2 perm 64k norm [0,4] QUAD net2 [0,11] QUAD dat2 AUT Active c2 perm 64k norm [0,4] QUAD net2 [0,11] QUAD dat2 AUT Active c2 perm 64k norm [0,4] QUAD net2 [0,11] QUAD dat2 AUT Active
c3 perm 64k norm [0,5] QUAD net1 [0,13] QUAD dat1 AUT Active
c3 perm 64k norm [0,5] QUAD net1 [0,13] QUAD dat1 AUT Active c3 perm 64k norm [0,5] QUAD net1 [0,13] QUAD dat1 AUT Active c3 perm 64k norm [0,5] QUAD net1 [0,13] QUAD dat1 AUT Active
c4 perm 64k norm [0,5] QUAD net2 [0,13] QUAD dat2 AUT Active
c4 perm 64k norm [0,5] QUAD net2 [0,13] QUAD dat2 AUT Active c4 perm 64k norm [0,5] QUAD net2 [0,13] QUAD dat2 AUT Active c4 perm 64k norm [0,5] QUAD net2 [0,13] QUAD dat2 AUT Active
c5 perm 64k norm [0,6] QUAD net1 [0,7] QUAD dat1 AUT Active
c5 perm 64k norm [0,6] QUAD net1 [0,7] QUAD dat1 AUT Active c5 perm 64k norm [0,6] QUAD net1 [0,7] QUAD dat1 AUT Active c5 perm 64k norm [0,6] QUAD net1 [0,7] QUAD dat1 AUT Active
c6 perm 64k norm [0,6] QUAD net2 [0,7] QUAD dat2 AUT Inactive
c6 perm 64k norm [0,6] QUAD net2 [0,7] QUAD dat2 AUT Inactive c6 perm 64k norm [0,6] QUAD net2 [0,7] QUAD dat2 AUT Inactive c6 perm 64k norm [0,6] QUAD net2 [0,7] QUAD dat2 AUT Inactive
A) add circuit L) search circuit A) add circuit L) search circuit A) add circuit L) search circuit A) add circuit L) search circuit
D) delete circuit E) edit circuit
D) delete circuit E) edit circuit D) delete circuit E) edit circuit D) delete circuit E) edit circuit
P) prev page I) activate circuit P) prev page I) activate circuit P) prev page I) activate circuit P) prev page I) activate circuit
N) next page R) deactivate circuit
N) next page R) deactivate circuit N) next page R) deactivate circuit N) next page R) deactivate circuit
X) exit this menu X) exit this menu X) exit this menu X) exit this menu
A [127.127.127.67] [0,1] SCM > A [127.127.127.67] [0,1] SCM > A [127.127.127.67] [0,1] SCM > A [127.127.127.67] [0,1] SCM >