Ethernet and slip parameters, Ethernet and slip parameters -12 – Verilink SCM (880-503300-001) Product Manual User Manual

Page 50

Administration Menu

4-12

Verilink SCM

The TCP/IP configuration parameters are standard Ethernet and
SLIP parameters. Consult with your system administrators to obtain
IP address information that is valid for your local TCP/IP network.

Since the Ethernet IP address and SLIP IP address will be at a factory
default value in a new SCM module, it will always be necessary to
use the Craft interface L

OCAL

port at least once to set the Ethernet

and/or SLIP IP addresses. Thereafter, if desired, the Craft interface
can be accessed via Telnet over Ethernet or SLIP.

From the SCM Administration Menu, select N to access the TCP/IP
Configuration Menu.

Upon entering a number of the routines under the TCP/IP
Configuration Menu, the user is advised that this will cause a reset
of the SCM in five minutes. This is done because the TCP/IP stack
runs at a level below the Craft interface. When changes are made to
the SNMP or other TCP/IP related functions, the SCM must be reset
before the changes take effect.

Figure 4-11 Network Configuration Menu

Ethernet and SLIP

Parameters

The parameter fields at the top of the TCP/IP Configuration Menu
reflect the values you enter using the menu commands at the
bottom of the menu.

-- TCP/IP CONFIGURATION MENU --

Ethernet type: Ethernet 2

Ethernet type: Ethernet 2
Ethernet MAC address: A0:6A:00:09:7D:BE

Ethernet MAC address: A0:6A:00:09:7D:BE

Ethernet MAC address: A0:6A:00:09:7D:BE
Enet IP address/subnet mask: [192.94.45.242] / [255.255.255.0]

Enet IP address/subnet mask: [192.94.45.242] / [255.255.255.0]

Enet IP address/subnet mask: [192.94.45.242] / [255.255.255.0]
Gateway address: [192.94.45.4]

Gateway address: [192.94.45.4]

Gateway address: [192.94.45.4]
Ethernet trap addresses: [192.94.45.229] [0.0.0.0]

Ethernet trap addresses: [192.94.45.229] [0.0.0.0]

Ethernet trap addresses: [192.94.45.229] [0.0.0.0]
[0.0.0.0] [0.0.0.0]

[0.0.0.0] [0.0.0.0]

SLIP IP address/subnet mask: [192.94.47.141] / [255.255.255.0]

SLIP IP address/subnet mask: [192.94.47.141] / [255.255.255.0]
SLIP trap sddresses: [192.94.47.8] [0.0.0.0]

SLIP trap sddresses: [192.94.47.8] [0.0.0.0]

SLIP trap sddresses: [192.94.47.8] [0.0.0.0]
[0.0.0.0] [0.0.0.0]

[0.0.0.0] [0.0.0.0]

Read community string: public

Read community string: public
Write community string: public

Write community string: public

I) Ethernet IP address L) SLIP IP address

I) Ethernet IP address L) SLIP IP address
M) Ethernet subnet mask S) SLIP subnet mask

M) Ethernet subnet mask S) SLIP subnet mask

M) Ethernet subnet mask S) SLIP subnet mask
G) gateway IP address R) SNMP read community string

G) gateway IP address R) SNMP read community string

G) gateway IP address R) SNMP read community string
T) Ethernet type W) SNMP write community string

T) Ethernet type W) SNMP write community string

T) Ethernet type W) SNMP write community string
P) Ethernet trap addresses E) SLIP trap addresses

P) Ethernet trap addresses E) SLIP trap addresses

P) Ethernet trap addresses E) SLIP trap addresses
X) exit this menu

X) exit this menu

A [0.0.0.2] [1,1] SCM >