Gasboy CFN Series CFN II Quick Reference - Manual (Page 9)

CFN II Quick Reference
C09159 Rev. 2238 5
IF command for conditional branching in command
files.
Options: -[!] {Y [text] | E filename |
{= | < | <= | > | >=} arg1 arg2}
-! negation operator; comes between dash (-)
and conditional expression; reverses the
truth conditions of the conditional
expression it proceeds
-Y text the text is echoed, and if the user enters a
1, Y, or y, then the command following the
IF statement is executed
-E filename if the named file exists, the
command following the IF statement is
executed
-or-
-{= |< | <= | > | >=} arg1 arg2} the command or
block of commands following the IF
statement is executed if =, <, <=, >, or >=
holds between arg1 and arg2; that is, if arg1
{comparison} arg2 is true. You can separate
expressions by |, which means “or,” or by &,
which means “and”
INSTALL disk-based command for hard drive
installation.
KERMIT disk-based program for file transfer to
external computer. Note: press CTRL-SHIFT-6 to
exit from connect mode.
Options: [baud][D][L#]
{R | S file1 [file2] ...}
baud data transmission rate to use, in bits-per-
second
D debug mode (used in development only)
L# Site Controller RS-232 port number to use;
where # is the port number
(without R or S) connect mode; default is port
number 1
-or-
R receive-file(s) mode
-or-
S file1 [file2] ... send the specified file(s) to the
connected computer
lddrawer a shift-change command to enter the
initial amount in the cash drawer at the beginning of
a shift on a console.
Options: [POS#] [$amount]
listday a shift-change command; with the 0
argument, it moves the PREVIOUS.LOG file to the
reports directory; with the 1 argument, it completes
the processing of the PREVIOUS.LOG file.
Options: 0 | 1 [POS#] [shift# POS#] . . .
listnext a shift-change command to generate a shift
report.
Options: [filename] [filename-extension only]
[%I | shift sequence#] [shift#] [POS#]
[printer# on POS]
listone a shift-change command that runs the
cashier, pritem, and prhour commands to generate the
end-of-day reports.
Options: [filename-extension only] [POS#]
[POS#] the number of the console associated
with the receipt printer where the end-of-day
report is to be printed
LOad ALlocation (78) enters amounts in allocation
totalizers.
Option: C
LOad Authorization (30) enters authorization code
for allowed fuels or disallowed merchandise.
Options: CI
I
option erases all authorization codes
LOad CArd (146) is run by a remote host to
download a bit-mapped lockout file.
Option: C
LOad CRon (76) creates cron entries.
Options: CI
I
option removes all entries from the cron file
Action types: @ ! ^ % ? #
@ DWMMDDYYHHMM command is a timed
entry
! command executes at a system restart
^ command executes at boot
% command executes when transaction file is
near full
# command executes immediately after loading
then command is removed from cron table
Note: an optional hyphen (-) after the action type
and before the command name suppresses
output to the printer.
LOad CUtoff (40) enters pump-fill limit and slow-
to-cutoff point.
Option: C
LOad DAte (31) enters date and time.
LOad DRawer (32) enters initial amount of money
in cash drawer.
Option: C
LOad Fuel (33) assigns product codes, price codes,
and tank numbers to pumps.
Option: C