AMETEK i-iX Series II - Manual (Page 9)

User Manual California Instruments
i Series II / iX Series II / iM Series II 9
List of Figures
Figure 2-1: 3001iX / 9003iX - Voltage Current rating, AC mode .......................................................................... 18
Figure 2-2: 3001iX / 9003iX - Voltage Current Rating, DC mode ........................................................................ 18
Figure 2-3: 5001iX / 15003iX - Voltage Current rating, AC mode ........................................................................ 19
Figure 2-4: 5001iX / 15003iX - Voltage Current rating, DC mode ....................................................................... 19
Figure 2-5: 10001iX / 30003iX - Voltage Current rating, AC mode ...................................................................... 20
Figure 2-6: 10001iX / 30003iX - Voltage Current rating, DC mode ...................................................................... 20
Figure 2-7: 15001iX - Voltage Current rating, AC mode ...................................................................................... 21
Figure 2-8: 15001iX - Voltage Current rating, DC mode ...................................................................................... 21
Figure 2-9: Maximum RMS voltage versus frequency rating in 300V AC range. ................................................. 22
Figure 3-1: The 5001iX Power Source ................................................................................................................ 31
Figure 3-2: RS232C Cable for PC Connection wiring diagram – Units without USB. .......................................... 38
Figure 3-3: USB Connector pin orientation. ......................................................................................................... 38
Figure 3-4: Function Strobe Connection. ............................................................................................................. 40
Figure 3-5: Function Strobe / Trigger Output Accessory. .................................................................................... 41
Figure 3-6: Rear Panel View for the 3001i/3001iX (Series II) .............................................................................. 43
Figure 3-7: Rear Panel View for the 3001i/3001iX (Series I, no USB) ................................................................. 44
Figure 3-8: Rear Panel View for the 5001i/5001iX (Series II) .............................................................................. 45
Figure 3-9: Rear Panel View for the 5001i/5001iX (Series I, no USB) ................................................................. 46
Figure 3-10: Connection For Single Power Source (5001iX/i, 3001iX/i) .............................................................. 49
Figure 3-11: Functional Test Setup ..................................................................................................................... 50
Figure 3-12: Single Phase 10000 VA System (10001iX/i) .................................................................................. 51
Figure 3-13: Two Phase 10000 VA System (10002i/iX – One Controller) ........................................................... 52
Figure 3-14: Three Phase 15000 VA System (15003iX/i-LK Three Controllers) ................................................. 53
Figure 3-15: Single Phase 15000 VA System (15001iX/i) .................................................................................. 54
Figure 3-16: Three-Phase 15000 VA system (15003iX/i - One Controller) ......................................................... 55
Figure 3-17: Connection With MODE Option ...................................................................................................... 56
Figure 3-18: Two Phase 10000 VA System (10002i-LK Two Controllers) .......................................................... 57
Figure 3-19: Three-Phase 9000 VA System (9003iX/i – One Controller) ........................................................... 58
Figure 4-1: Shuttle Knob ...................................................................................................................................... 60
Figure 4-2: FUNCTION keypad .......................................................................................................................... 61
Figure 4-3: Entering value from decimal keypad ................................................................................................ 62
Figure 4-4: Cursor UP key movement ................................................................................................................ 63
Figure 4-5: Cursor DOWN key movement .......................................................................................................... 63
Figure 4-6: Main Menu 1 screen ......................................................................................................................... 64
Figure 4-7: Menu 1 through 3 ............................................................................................................................. 65
Figure 4-8: PROGRAM Menu ............................................................................................................................. 69
Figure 4-9: MEASUREMENTS Screen, single phase and three phase modes .................................................. 71
Figure 4-10: HARMONICS/TRACE ANALYSIS screen ...................................................................................... 73
Figure 4-11: TRANSIENTS menu ....................................................................................................................... 76
Figure 4-12: VOLTAGE SURGE/SAG SETUP screen ....................................................................................... 77
Figure 4-13: VOLTAGE SWEEP/STEP SETUP screen ..................................................................................... 79
Figure 4-14: FREQUENCY SWEEP/STEP SETUP screen ................................................................................ 81
Figure 4-15: VOLTAGE/FREQUENCY SWEEP/STEP SETUP screen .............................................................. 82
Figure 4-16: START/VIEW TRANSIENT SEQUENCE screen ............................................................................ 83
Figure 4-17: WAVEFORMS menu ...................................................................................................................... 84
Figure 4-18: APPLICATIONS menu ................................................................................................................... 87
Figure 4-19: SETUP REGISTERS menu ............................................................................................................ 88
Figure 4-20: UTILITY menus .............................................................................................................................. 89
Figure 4-21: GPIB/RS232 SETUP menu ............................................................................................................ 92
Figure 4-22: VOLTAGE/CURRENT CONTROL SETUP menu........................................................................... 93
Figure 4-23: INITIAL SETUP menus ................................................................................................................... 95
Figure 4-24:LIMIT SETUP menu ......................................................................................................................... 97
Figure 4-25: CONFIGURATION SETUP Menus .................................................................................................. 98
Figure 4-26: OUTPUT IMPEDANCE menu ....................................................................................................... 101
Figure 4-27: MEASUREMENT CAL FACTORS menu ...................................................................................... 102
Figure 4-28: OUTPUT CAL FACTORS menu.................................................................................................... 103
Figure 4-29: Selecting a waveform .................................................................................................................... 106
Figure 4-30: Selecting waveforms for single phase or all phases ..................................................................... 106
Figure 4-31: Custom waveform creation with GUI program ............................................................................... 107
Figure 4-32: Waveform crest factor affects max. rms voltage............................................................................ 108