Rockwell Automation MV SMC Flex Motor Controller (for Series K or later) - Manual (Page 84)

74 Rockwell Automation Publication 1560E-UM051F-EN-P - June 2013
Chapter 4 Programming
Table 6 - Parameter Linear List
(1)
Parameter No. Description Parameter No. Description Parameter No. Description
1 Volts Phase A-B 46 Motor FLC 91 Data In B2
2 Volts Phase B-C 47 Overload Reset 92 Data In C1
3 Volts Phase C-A 48 OL Shunt Time 93 Data In C2
4 Current Phase A 49 OL Trip Enable 94 Data In D1
5 Current Phase B 50 Overload A Lvl 95 Data In D2
6 Current Phase C 51 Underload F Lvl 96 Data Out A1
7 Watt Meter 52 Underload F Dly 97 Data Out A2
8 Kilowatt Hours 53 Underload A Lvl 98 Data Out B1
9 Elapsed Time 54 Underload A Dly 99 Data Out B2
10 Meter Reset 55 Undervolt F Lvl 100 Data Out C1
11 Power Factor 56 Undervolt F Dly 101 Data Out C2
12 Mtr Therm Usage 57 Undervolt A Lvl 102 Data Out D1
13 Motor Speed 58 Undervolt A Dly 103 Data Out D1
14 SMC Option 59 Overvolt F Lvl 104 Motor ID
15 Motor Connection
(2)
60 Overvolt F Dly 105 CT Ratio
16 Line Voltage 61 Overvolt A Lvl 106 MV Ratio
17 Starting Mode 62 Overvolt A Dly 107 Aux1 Config
18 Ramp Time 63 Unbalance F Lvl 108 Aux3 Config
19 Initial Torque 64 Unbalance F Dly 109 Aux4 Config
20 Cur Limit Level 65 Unbalance A Lvl 110 Aux2 Config
21 Reserved 66 Unbalance A Dly 111 Language
22 Kickstart Time 67 Jam F Lvl 112 Timed Start (2)
23 Kickstart Level 68 Jam F Dly 113 I Shutoff Level
(2)
24 Option 2 Input 69 Jam A Lvl 114 UTS Level
25 Starting Mode 2 70 Jam A Dly 115 Parameter Mgmt
26 Ramp Time 2 71 Stall Delay 116 Backspin Timer
27 Initial Torque 2 72 Gnd Flt Enable 117 V Shutoff Level
28 Cur Limit Level 2 73 Gnd Flt Level 118 OL Reset Level
29 Reserved 74 Gnd Flt Delay 119 Ambient Temp.
(2)
30 Kickstart Time 2 75 Gnd Flt Inh Time 120 Notch Position
(2)
31 Kickstart Level 2 76 Gnd Flt A Enable 121 Notch – Maximum (2)
32 Stop Mode 77 Gnd Flt A Lvl 122 Start Delay
33 Stop Time 78 Gnd Flt A Dly 123 Bypass Delay
(2)
34 Pump Pedestal (1) 79 PTC Enable 124 Fault 1
35 Braking Current 80 Phase Reversal 125 Fault 2
36 Braking Time (3) 81 Starts Per Hour 126 Fault 3
37 Load Type 82 Restart Attempts 127 Fault 4
38 High Eff Brake 83 Restart Delay 128 Fault 5
39 Slow Speed Sel 84 Line Fault 129 Start Time E
40 Slow Speed Cur 85 Emergency Run 130 Start Time 2E
41 Slow Accel Cur 86 Current Loss 131 Stop Time E
42 Slow Running Cur 87 Logic Mask 132 Option 1 Input
43 Stopping Current 88 Data In A1 133 Stop Input
44 Overload Class 89 Data In A2 134 Elapsed Time 2
45 Service Factor 90 Data In B1
(1) Pump Control module only – see Troubleshooting section for guidance.
(2) Do not change these parameters from the default settings.
(3) Brake module only – Consult factory.