Campbell Scientific CR23X Micrologger User Manual

Page 371

CR23X INDEX

INDEX-9

Step Loop Index - [Instruction 90] 12-4
Stop Bit 6-7
Storage

see Final Storage, Input Storage, and
Intermediate Storage

Storage and retrieval options, Data OV-20, 4-1, 6-1
Storage Module Pointer (SPTR) 2-2
Storage Modules 4-4

Addressing with CR23X 4-2, 4-5
Commands to (

Mode) 4-6

Current drain, Typical 14-1
File Mark 4-4
Manually initiated data output (

Mode)

4-5
Save/load program (

Mode) 1-11

Use with Instruction 96 4-1, 4-5

Storage peripherals, External 4-1
Store Area, see Set Active Storage Area -

[Instruction 80]

Strip charts

Converting 0-360 wind direction output

to 0-540 8-7

Use with SDM-AO4 8-7

Subroutines

Entering 1-2
Label Subroutine - [Instruction 85] 12-1
Port Interrupt Subroutines 12-1
Programming Examples 8-10, 8-20

Subtract - [Instruction 35] 10-1
SW8A Switch Closure Input Module, see

SDM-SW8A

Switch 12V channel OV-3, OV-4, 14-6

Programming example 8-22

Switch closure

Counting on Tipping Bucket

Rain Gage 8-5

Measuring 9-1

Switch Closure Input Module, see SDM-SW8A
Switching power to a device 14-7
Synchronous, Definition A-3
Synchronous Device Communication (SDC) 6-4
System memory OV-5, 1-7
System status (

Mode) 1-9

Tables, List of LT-1

see also Program Tables

Table overruns 1-10, 9-3, A-3
TC, see Thermocouples
TD (Transmitted Data) 6-6
TDR, see SDM-TDR

Telecommunication 5-1

Automatic setting of baud rate 5-1
Automatic time-out from 5-2
Commands 5-3
Key definitions OV-11
Password/Security 5-4
Remote keyboard OV-11, 5-5
Telecommunication states 5-4
with Binary responses C-1

Telecommunications Command OV-12
Telecommunications (Modem) Pointer (MPTR) 2-2
Temp (107), see 107 Thermistor Probe -

[Instruction 11]

Temp, Module, see Internal Temperature -

[Instruction 17]

Temp RTD, see Temperature from Platinum

R.T.D. - [Instruction 16]

Temp TC DIFF, see Thermocouple Temperature

Measurement - [Instruction 14]

Temp TC SE, see Thermocouple Temperature

Measurement - [Instruction 13]

Temperature from Platinum R.T.D. -

[Instruction 16] 9-9
Programming examples 7-4, 7-5, 7-6, 8-13

Temperature from thermocouples, see

Thermocouple temperature

Temperature of Module, see Internal

Temperature - [Instruction 17]

Temperature range, CR23X 14-1
Terminal emulator OV-12
TGT1 Telonics GOES - [Instruction 99] 12-10
Thermocouple Measurements 13-12
Thermocouple Reference Junction 13-11, OV-

2, OV-16, 13-13

Programming Example 7-4

Thermocouple Temperature Measurement

Differential - [Instruction 14] 9-8
Programming example OV-16, 7-2
Single-Ended Measurement -

[Instruction 13] 9-7

Technique/error analysis 13-13
Using an External Reference Junction 7-3

Three Wire Half Bridge - [Instruction 7] 9-5,

13-17, 13-18, 13-19
Programming example 7-5

Throughput rate, Definition 1-1, A-3
Time - [Instruction 18] 9-9

Programming example 12-4

Time

Execution time requirements for instructions 3-6
Real Time, see Record Real Time -

[Instruction 77]

Setting/displaying (

Mode) 1-4

Standard Deviation in Time - [Instruction 82]

11-7