beautypg.com

NORD Drivesystems BU0550 User Manual

Page 2

background image

PLC logic for NORD SK 54xE frequency inverters

Safety information

2

BU 0550 GB-0813

N O R D Frequency inverters

Safety and operating instructions for

drive power converters

(as per: Low Voltage Directive 2006/95/EEC )

1. General

Depending on their protection class, drive power converters may
have live, bare, moving or rotating parts or hot surfaces during
operation.

Unauthorised removal of covers, improper use, incorrect installation
or operation causes a risk of serious personal injury or material
damage.

Further information can be found in this documentation.

All transportation, installation, initialisation and maintenance work
must be carried out by qualified personnel (compliant with IEC
364, CENELEC HD 384, DIN VDE 0100, IEC 664 or DIN VDE 0110,
and national accident prevention regulations).

For the purposes of these basic safety instructions, qualified
personnel are persons who are familiar with the assembly,
installation, commissioning and operation of this product and who
have the relevant qualifications for their work.

2. Proper use in Europe

Drive power converters are components intended for installation in
electrical systems or machines.

When installed in machines, the drive power converter cannot be
commissioned (i.e. commencement of the proper use) until it has
been ensured that the machine meets the provisions of the EC
Directive 2006/42/EEC (Machine Directive); EN 60204 must also be
complied with.

Commissioning (i.e. implementation of the proper use) is only
permitted if the EMC Directive (2004/108/EEC) is complied with.

Drive power converters with the CE mark meet the requirements of
the Low Voltage Directive 2006/95/EEC. The harmonized standards
stated in the Declaration of Conformity are used for the drive power
converters.

Technical data and information for connection conditions can be
found on the rating plate and in the documentation, and must be
complied with.

The drive power converters may only be used for the safety
functions which are described and for which they have been
explicitly approved.

3. Transport, storage

Information regarding transport, storage and correct handling must
be complied with.

4. Installation

The installation and cooling of the equipment must be implemented
according to the regulations in the corresponding documentation.

The drive power converters must be protected against
impermissible loads. Especially during transport and
handling, components must not be deformed and/or
insulation distances must not be changed. Touching of
electronic components and contacts must be avoided.

Drive power converters have electrostatically sensitive
components, which can be easily damaged by incorrect
handling. Electrical components must not be mechanically
damaged or destroyed (this may cause a health hazard!).

5. Electrical connections

When working on live drive power converters, the applicable
national accident prevention regulations must be complied
with (e.g. VBG A3, formerly VBG 4).

The electrical installation must be implemented according to
the applicable regulations (e.g. cable cross-section, fuses,
ground lead connections). Further information is contained
in the documentation.

Information about EMC-compliant installation

– such as

shielding, earthing, location of filters and installation of
cables can be found in the drive power converter
documentation. These instructions must be complied with
even with CE marked drive power converters. Compliance
with the limiting values specified in the EMC regulations is
the responsibility of the manufacturer of the system or
machine.

6. Operation

Where necessary, systems where drive power converters
are installed must be equipped with additional monitoring
and protective equipment according to the applicable safety
requirements,

e.g.

legislation

concerning

technical

equipment, accident prevention regulations, etc.

The parameterisation and configuration of the drive power
converter must be selected so that no hazards can occur.

All covers must be kept closed during operation.

7. Maintenance and repairs

After the drive power converter is disconnected from the
power supply, live equipment components and power
connections should not be touched immediately, because of
possible charged capacitors. Observe the relevant
information signs located on the drive power converter.

Further information can be found in this documentation.

These safety instructions must be kept in a safe place!