KEPCO BOP-GL 1KW Operator Manual Firmware Ver.3.05 and higher - Manual (Page 12)

iv
BOP-1K 022814
TABLE OF CONTENTS
SECTION PAGE
SECTION 4 - CALIBRATION
4.1 General ................................................................................................................................................... 4-1
4.2 Test Equipment Requirements ............................................................................................................... 4-3
4.3 Calibration using Remote SCPI commands via GPIB or RS 232 Interface ............................................ 4-3
4.3.1 Calibration Procedure using SCPI Commands................................................................................. 4-5
4.3.2 Calibration of Series- or Parallel-Connected Units ........................................................................... 4-10
4.4 Calibration Storage ................................................................................................................................. 4-10
APPENDIX A - SCPI COMMON COMMAND/QUERY DEFINITIONS
A.2 *CLS — Clear Status Command ............................................................................................................ A-1
A.3 *ESE — Standard Event Status Enable Command................................................................................ A-1
A.4 *ESE? — Standard Event Status Enable Query..................................................................................... A-2
A.5 *ESR? — Event Status Register Query.................................................................................................. A-2
A.6 *IDN? — Identification Query.................................................................................................................. A-2
A.7 *OPC — Operation Complete Command ............................................................................................... A-2
A.8 *OPC? — Operation Complete Query .................................................................................................... A-3
A.9 *OPT? — Options Query ........................................................................................................................ A-4
A.10 *RCL — Recall Command ...................................................................................................................... A-4
A.11 *RST — Reset Command....................................................................................................................... A-4
A.12 *SAV — Save Command........................................................................................................................ A-4
A.13 *SRE — Service Request Enable Command ......................................................................................... A-5
A.14 *SRE? — Service Request Enable Query .............................................................................................. A-5
A.15 *STB? — Status Byte Register Query .................................................................................................... A-5
A.16 *TRG — Trigger Command .................................................................................................................... A-5
A.17 *TST? — Self Test Query ....................................................................................................................... A-6
A.18 *WAI — Wait-To-Continue Command .................................................................................................... A-6
APPENDIX B - SCPI COMMAND/QUERY DEFINITIONS
B.1 Introduction ............................................................................................................................................. B-1
B.2 Numerical Values.................................................................................................................................... B-2
B.3 ABOR t Command................................................................................................................................... B-2
B.4 CAL Commands and Queries................................................................................................................. B-2
B.5 INIT iate [:IMM ediate ] Command ............................................................................................................ B-3
B.6 INIT iate :CONT inuous Command .......................................................................................................... B-4
B.7 INIT iate :CONT inuous Query ................................................................................................................. B-4
B.8 MEAS ure [:SCAL ar ]:CURR ent [:DC]? Query.......................................................................................... B-4
B.9 MEAS ure [:SCAL ar ]:MODE[:DC] Command .......................................................................................... B-4
B.10 MEAS ure [:SCAL ar ]:VOLT age [:DC]? Query .......................................................................................... B-4
B.11 MEAS ure [:SCAL ar ]:TRAN sient [:DC]? QUERY..................................................................................... B-4
B.12 MEM ory :UPD ate Command .................................................................................................................. B-5
B.13 OUTP ut [:STAT e ] Command................................................................................................................... B-6
B.14 OUTP ut [ : STAT e ] Query ......................................................................................................................... B-7
B.15 OUTP ut :CONT rol Command ................................................................................................................. B-7
B.16 OUTP ut :CONT? Query .......................................................................................................................... B-7
B.17 OUTP ut :MODE Command ..................................................................................................................... B-7
B.18 OUTP ut :MODE? Query.......................................................................................................................... B-7
B.19 [SOUR ce :]CURR ent [:LEV el ][:IMM ediate ][:AMP litude ] Command....................................................... B-7
B.20 [SOUR ce :]CURR ent [:LEV el ][:IMM ediate ][:AMP litude ] Query ............................................................. B-8
B.21 [SOUR ce :]CURR ent [:LEV el ]:LIM it [:BOTH] Command .......................................................................... B-8
B.22 [SOUR ce :]CURR ent [:LEV el ]:LIM it [:BOTH]? Query............................................................................... B-9
B.23 [SOUR ce :]CURR ent [:LEV el ]:LIM it :NEG Command .............................................................................. B-9
B.24 [SOUR ce :]CURR ent [:LEV el ]:LIM it :NEG? Query ................................................................................... B-9
B.25 [SOUR ce :]CURR ent [:LEV el ]:LIM it :POS Command .............................................................................. B-9