Chapter 9: programming page for tru-tune – Watlow Series SD PID Profiling Controller User Manual
Page 47
Wa t l o w S e r i e s S D
•
4 5
•
C h a p t e r 9 P r o g r a m m i n g f o r T R U - T U N E + ™
Chapter 9: Programming Page
for TRU-TUNE+™
9
The Programming Page allows you to select what parameters appear on the Operations Page. To go to the Pro-
gramming Page, press both the Advance ‰ and Infinity ˆ keys for six seconds from the Home Page. [Prog] will
appear in the upper display and
[PAgE] will appear in the lower display.
• Press the Advance Key ‰ to move through the parameter prompts.
• Press the Up ¿ or Down ¯ key to change the parameter value.
• Press the Infinity Key ˆ at any time to return to the Home Page display.
Note: This chapter only applies to the TRU-TUNE+™ version of the Series SD (SD_E - _ _ _ _ - _ _ _ _).
Display
Parameter name
Description
Settings
Range
(Integer values for Modbus
in parentheses.)
Default
Modbus
(less 40,001
offset)
Read/Write
Appears if"
[~~P1]
Parameter Location 1
[none]
(0) None
[`CAL]
(1) Calibration Offset
[`C-F]
(2) Temperature Units (Setup
Page)
[A1;Lo]
(3) Alarm 1 Low
[A1;hi]
(4) Alarm 1 High
[A2;Lo]
(5) Alarm 2 Low
[A2;hi]
(6) Alarm 2 High
[A3;Lo]
(7) Alarm 3 Low
[A3;hi]
(8) Alarm 3 High
[hys1]
(9) Alarm Hysteresis 1 (Setup
Page)
[hys2]
(10) Alarm Hysteresis 2 (Setup
Page)
[hyS3]
(11) Alarm Hysteresis 3 (Setup
Page)
[addr]
(12) Modbus Device Address
(Setup Page)
[`Aut]
(13) Autotune
[A-m]
(14) Auto-Manual
[Po;ht]
(15) Power Heat
[Po;CL]
(16) Power Cool
[ht;M]
(17) Heat Control Method
[Pb;ht]
(18) Prop. Band Heat
[It;hc]
(19) Integral
[dE;hc]
(20) Derivative
[db;hc]
(21) Dead Band
[h;hys]
(22) Heat Hysteresis
[CL;M]
(23) Cool Control Method
[Pb;Cl]
(24) Prop. Band Cool
[C;hys]
(28) Cool Hysteresis
[prop]
(29) Proportional Term
[``It]
(30) Integral Term
[``dE]
(31) Derivative Term
[rP;rt]
(32) Ramp Rate (Setup Page)
[````]
(33)
[````]
(34)
[~```]
(35)
[t;tun]
(36) TRU-TUNE+™ Enable
[Po;ht] (15) 48 R/W
All parameter loca-
tions always appear
on the Programming
Page.
[~~P2]
Parameter Location 2
[A-m] (14) 49 R/W
[~~P3]
Parameter Location 3
[`Aut] (13) 50 R/W
[~~P4]
Parameter Location 4
[t;tun] (36) 51 R/W
[~~P5]
Parameter Location 5
[`CAL] (1)
52 R/W
[~~P6]
Parameter Location 6
[ht;m] (17) 53 R/W
[~~P7]
Parameter Location 7
[pb;ht] (18)
54 R/W
[~~P8]
Parameter Location 8
[h;hys] (22)
55 R/W
[~~P9]
Parameter Location 9
[CL;m] (23) 56 R/W
[~P10]
Parameter Location 10
[pb;cl] (24) 57 R/W
[~P11]
Parameter Location 11
[C;hys] (28) 58 R/W
[~P12]
Parameter Location 12
[It;hc]
(19) 59 R/W
[~P13]
Parameter Location 13
[dE;hc] (20)
60 R/W
[~P14]
Parameter Location 14
[A1;hi] (4)
61 R/W
[~P15]
Parameter Location 15
[A1;Lo] (3)
62 R/W
[~P16]
Parameter Location 16
[A2;hi] (6)
63 R/W
[~P17]
Parameter Location 17
[A2;Lo] (5)
64 R/W
[~P18]
Parameter Location 18
[A3;hi] (8)
65 R/W
[~P19]
Parameter Location 19
[A3;Lo] (7)
66 R/W
[~P20]
Parameter Location 20
[none] (0)
67 R/W
Note: All parameter locations have the same range of possible values.