Watlow Series SD PID Profiling Controller - Manual (Page 42)

Wa t l o w S e r i e s S D • 4 0 • C h a p t e r 7 O p e r a t i o n s f o r T R U - T U N E + ™
7
These parameters can be selected to appear in the Operations Page. Select the parameters you want to appear in
the Operations Page in the Programming Page. Press the Advance Key ‰ to enter the Operations Page and to step
through the parameters. For profiling controllers, set
[Prog] to [``no] to access the Operations Page. Press the
Infinity Key ˆ to return to the Home Page at any time.
Note: This chapter only applies to the TRU-TUNE+™ version of the Series SD (SD_E - _ _ _ _ - _ _ _ _).
Chapter 7:
Operations Parameters Table
for TRU-TUNE+™
Display Parameter name
Description
Settings Range Default Modbus*
(less 40,001 offset)
Read/Write
Appears if"
[Po;ht]
[Po.ht] Power Heat
Displays the current heat con-
trol power.
0.0 to 100.0% power (000
to 10000) (Two decimal
places implied for Mod-
bus.)
NA 256 R [A-M] is set to
[auto] and at least
one output is set to
[hEAt].
[Po;CL]
[Po.CL] Power Cool
Displays the current cool con-
trol power.
0.0 to 100.0% power (000
to 10000) (Two decimal
places implied for Mod-
bus.)
NA 257 R [A-M] is set to
[auto] and at least
one output is set to
[Cool].
[A-M]
[A-M] Auto-Manual Mode
Set the control mode.
[auto] (0)
[Man] (1) [auto]
(0) 25 R/W Always appears.
[`Aut]
[ Aut] Autotune
Start an autotune.
[`OFF] off (0)
[``On] on (1) [`OFF]
(0) 215 R/W At least one output
is set to
[hEAt] or
[Cool].
[t;tun]
[t.tun] TRU-TUNE+™ Enable
Enable or disable the TRU
TUNE+™ adaptive tuning
feature.
[``no] No (0)
[`yES] Yes (1) [`yES] 350
rw
TRU-TUNE+™ version
only. (SD_ E - _ _ _ _
- _ _ _ _ ).
[`CAL]
[ CAL] Calibration Offset
Offset the input reading.
-999 to 999
(-999000 to 999000)
0.0 *85, 86 R/W Always appears.
[ht;m]
[ht.M] Heat Control
Method Set the heat control
method.
[`OFF] off (0)
[`PID] PID (1)
[on;of] on-off (2) [`PID]
(1) 213 R/W At least one output is
set to
[hEAt].
[Pb;ht]
[Pb.ht] Proportional Band Heat
Set the proportional band for
the heat outputs.
1 to 999°F, if [`Sen] is
set to [``tc] or [`rtd]
(1000 to 999000)
0.000 to 999 units, if
[`Sen] is set to [`mA]
or
[uolt]. (0000 to
999000)
25 25 *335, 336 R/W
*339, 340 R/W At least one output
is set to
[hEAt]
and [ht;m] is set to
[`PId].
[It;hc]
[It.hc] Integral
Set the PID integral in
seconds per repeat for all
outputs.
0.00 to 3,600 seconds per
repeat (0000 to 3600)
0.00: disabled
180.0 *343, 344 R/W TRU-TUNE+™ ver-
sion only. (SD_E - _ _
_ _ - _ _ _ _ ).
[ht;m]
and/or [CL;m] is set
to [`PId].
Note: Parameters appear in the Operations Page only if activated from the programming page. See page 22 for Operations Page defaults.
Note: Some values will be rounded off to fit in the four-character display. Full values can be read with Modbus. All temperature param-
eters through Modbus are in °F, by default.
* Low register numbers contain the two higher bytes; high register numbers contain the two lower bytes of the four-byte integer. Decimal
precision is implied at three decimal places unless otherwise noted.
**** This value multiplied by 100 equals the percent power.