Watlow Series SD PID Profiling Controller - Manual (Page 45)

Wa t l o w S e r i e s S D • 4 3 • C h a p t e r 8 P r o g r a m m i n g
Chapter 8: Programming Page
8
The Programming Page allows you to select what parameters appear on the Operations Page. To go to the Pro-
gramming Page, press both the Advance ‰ and Infinity ˆ keys for six seconds from the Home Page. [Prog] will
appear in the upper display and
[PAgE] will appear in the lower display.
• Press the Advance Key ‰ to move through the parameter prompts.
• Press the Up ¿ or Down ¯ key to change the parameter value.
• Press the Infinity Key ˆ at any time to return to the Home Page display.
Note: This chapter only applies to the static set point and profiling versions of the Series SD (SD_C or R - _ _ _ _ - _ _ _ _).
Display Parameter name
Description
Settings Range
(Integer values for Modbus
in parentheses.)
Default Modbus*
(less 40,001
offset)
Read/Write
Appears if"
[``P1] Parameter Location 1 [none] (0) None
[`CAL] (1) Calibration Offset
[`C-F] (2) Temperature Units (Setup
Page)
[A1;Lo] (3) Alarm 1 Low
[A1;hi;] (4) Alarm 1 High
[A2;Lo] (5) Alarm 2 Low
[A2;hi] (6) Alarm 2 High
[A3;Lo] (7) Alarm 3 Low
[A3;hi] (8) Alarm 3 High
[hys1] (9) Alarm Hysteresis 1 (Setup
Page)
[hys2] (10) Alarm Hysteresis 2 (Setup
Page)
[hyS3] (11) Alarm Hysteresis 3 (Setup
Page)
[addr] (12) Modbus Device Address
(Setup Page)
[`Aut] (13) Autotune
[A-m] (14) Auto-Manual
[Po;ht] (15) Power Heat
[Po;CL] (16) Power Cool
[ht;M] (17) Heat Control Method
[Pb;ht] (18) Prop. Band Heat
[It;ht] (19) Integral Heat or
[re;ht] (19) Reset Heat
[dEht] (20) Derivative Heat or
[ra;ht] (20) Rate Heat
[db;ht] (21) Dead Band Heat
[h;hys] (22) Heat Hysteresis
[CL;M] (23) Cool Control Method
[Pb;Cl] (24) Prop. Band Cool
[It;Cl] (25) Integral Cool or
[rE;Cl] (25) Reset Cool
[dE;Cl] (26) Derivative Cool or
[ra;Cl] (26) Rate Cool
[db;Cl] (27) Dead Band Cool
[C;hys] (28) Cool Hysteresis
[prop] (29) Proportional Term
[``It] (30) Integral Term
[``dE] (31) Derivative Term
[rP;rt] (32) Ramp Rate (Setup Page)**
[Po;ht] (15) 48 R/W All parameter loca-
tions always appear
on the Programming
Page.
Static set point ver-
sion
(SD_C - _ _ _ _ - _ _
_ _ ) P1 to P20
Profiling version
only.
(SD_R - _ _ _ _ - _ _
_ _ ) P1 to P23
[~~P2] Parameter Location 2 [`gsd] (35) 49 R/W
[~~P3] Parameter Location 3 [`Aut] (13) 50 R/W
[~~P4] Parameter Location 4 [`CAL] (1) 51 R/W
[~~P5] Parameter Location 5 [ht;m] (17) 52 R/W
[~~P6] Parameter Location 6 [pb;ht] (18) 53 R/W
[~~P7] Parameter Location 7 [re;ht] (19) 54 R/W
[``P8] Parameter Location 8 [ra;ht] (20) 55 R/W
[``P9] Parameter Location 9 [h;hys] (22) 56 R/W
[`P10] Parameter Location 10 [CL;m] (23) 57 R/W
[`P11] Parameter Location 11 [pb;Cl] (24) 58 R/W
[`P12] Parameter Location 12 [re;CL] (25) 59 R/W
[`P13] Parameter Location 13 [ra;Cl] (26) 60 R/W
[`P14] Parameter Location 14 [C;hys] (28) 61 R/W
[`P15] Parameter Location 15 [A1;hi] (4) 62 R/W
[`P16] Parameter Location 16 [A1;Lo] (3) 63 R/W
[`P17] Parameter Location 17 [A2;hi] (6) 64 R/W
[`P18] Parameter Location 18 [A2;Lo] (5) 65 R/W
[`P19] Parameter Location 19 [A3;hi] (8) 66 R/W
[`P20] Parameter Location 20 [A3Lo] (7) 67 R/W
[`P21] Parameter Location
21*** [Ent1] (32) 68 R/W
[`P22] Parameter Location
22*** [Ent2] (33) 69 R/W
[`P23] Parameter Location
23*** [Ent3] (34) 47 R/W
Note: All parameter locations have the same range of possible values.
**Static set point version (SD_ C - _ _ _ _ - _ _ _ _ )
***Profiling version only. (SD_ R - _ _ _ _ - _ _ _ _ )