6 connecting to physical alarm modules – Ronan X11CA Software Manual User Manual
Page 48
Rev 1.3 Series X11CA Computer Annunciators: X11CA Configuration Software User’s Manual
4. X11CA Software Operation
Hardware Control-© 2003 Ronan Engineering
44
E
E
x
x
a
a
m
m
p
p
l
l
e
e
:
:
F
F
i
i
g
g
u
u
r
r
e
e
4
4
-
-
1
1
(
(
M
M
o
o
d
d
u
u
l
l
e
e
1
1
:
:
3
3
c
c
h
h
a
a
n
n
n
n
e
e
l
l
s
s
,
,
M
M
o
o
d
d
u
u
l
l
e
e
2
2
:
:
4
4
c
c
h
h
a
a
n
n
n
n
e
e
l
l
s
s
)
)
X
X
1
1
1
1
C
C
A
A
-
-
I
I
M
M
S
S
w
w
i
i
t
t
c
c
h
h
:
:
P
P
R
R
G
G
M
M
Click on the System menu and then the PrintReport submenu.
Verify that the information is correct and there is no error messages.
X11CA SYSTEM REPORT.
File Access Info:
C:\ \SAMPLE-CONFIG.CFG
Created: 1/31/03 1:16:50 PM
Last Accessed: 1/31/03 1:16:50 PM
Last Modified: 1/20/03 10:15:11 AM
WIDHT : 2
HIGH : 1
GLOBAL SYSTEM PROPERTIES
TEST TYPE : OPERATIONAL TEST
HORN1 TYPE : Continuous
HORN2 TYPE : Continuous
CTA FOLLOW : FC,NNE
SERIAL DATA FOLLOW : FC
ALARM MODULES PROPERTIES
----------------------------------------------------------------------------------------------
|Module|Channel|Seq. |Input|FC Time|Ser. Output|AUX Rel | TO |HORN| GF1 | GF2 |Global
|Number|Number |Type |Type |Delay,s|Data Follow|Follow |Follow | |Inhibit|Inhibit|Prop.
----------------------------------------------------------------------------------------------
| 1 | 1 |A-1 | FC | 0.02 | FC |FC, NNE |FC, NNE| H1 | | | OK |
| | 2 |A-1 | FC | 0.02 | FC |FC, NNE |FC, NNE| H1 | | | OK |
| | 3 |A-1 | FC | 0.02 | FC |FC, NNE |FC, NNE| H1 | | | OK |
----------------------------------------------------------------------------------------------
| 2 | 1 |F3M-1| FC | 0.02 | FC |ACK, NNE|FC, NNE| H1 | | | OK |
| | 2 |F3M-1| FC | 0.02 | FC |ACK, NNE|FC, NNE| H1 | | | OK |
| | 3 |F3M-1| FC | 0.02 | FC |ACK, NNE|FC, NNE| H1 | | | OK |
| | 4 |F3M-1| FC | 0.02 | FC |ACK, NNE|FC, NNE| H1 | | | OK |
----------------------------------------------------------------------------------------------
*- The alarm module needs to be reprogrammed
x11CA – C:\sample-config.cfg page 1
1/31/03 2:11:34 PM
Figure 4-32 Example Report
4.6 Connecting to Physical Alarm Modules
Before making connection from the Configuration Software to physical alarm
modules, make sure that power to the X11CA-IM device is on and its switch 8
(SW8) is set to PRGM side.
When the X11CA-IM device is in the program mode, the red ERROR LED on the
X11CA-IM device keeps blinking because the Configuration Software bypasses the