Compaq AA-RHGWC-TE User Manual
Page 7
6.6.2
Install the Tru64 UNIX Operating System . . .. . . .. . .. . .. . .. .
6–51
6.6.3
Determining /dev/disk/dskn to Use for a Cluster
Installation . . .. . .. . .. . .. . . .. . .. . .. . .. . .. . . .. . .. . .. . .. . . .. . .. . .. . .. .
6–51
6.6.4
Label the Disks to Be Used to Create the Cluster . .. . .. . .. .
6–53
6.6.5
Install the TruCluster Server Software and Create the
First Cluster Member . . .. . .. . .. . .. . .. . . .. . .. . .. . .. . . .. . .. . .. . .. .
6–53
6.6.6
Reset the bootdef_dev Console Environment Variable . . .. .
6–53
6.6.7
Add Additional Systems to the Cluster . .. . .. . .. . . .. . .. . .. . .. .
6–55
6.7
Converting the HSG80 from Transparent to Multiple-Bus
Failover Mode . . . .. . .. . .. . .. . . .. . .. . .. . .. . .. . . .. . .. . .. . .. . . .. . .. . .. . .. .
6–57
6.7.1
Overview .. . . .. . .. . .. . .. . . .. . .. . .. . .. . .. . . .. . .. . .. . .. . . .. . .. . .. . .. .
6–58
6.7.2
Procedure to Convert from Transparent to Multiple-bus
Failover Mode . . .. . .. . .. . . .. . .. . .. . .. . .. . . .. . .. . .. . .. . . .. . .. . .. . .. .
6–59
6.8
Using the emx Manager to Display Fibre Channel Adapter
Information . . .. . . .. . .. . .. . .. . . .. . .. . .. . .. . .. . . .. . .. . .. . .. . . .. . .. . .. . .. .
6–62
6.8.1
Using the emxmgr Utility to Display Fibre Channel
Adapter Information .. . . .. . .. . .. . .. . .. . . .. . .. . .. . .. . . .. . .. . .. . .. .
6–62
6.8.2
Using the emxmgr Utility Interactively .. . .. . .. . . .. . .. . .. . .. .
6–65
7
Using GS80, GS160, or GS320 Hard Partitions in a TruCluster
Server Configuration
7.1
Overview . . .. . .. . . .. . .. . .. . .. . . .. . .. . .. . .. . .. . . .. . .. . .. . .. . . .. . .. . .. . .. .
7–1
7.2
Hardware Requirements for a Hard Partition in a Cluster . .. .
7–2
7.3
Configuring Partitioned GS80, GS160, or GS320 Systems in a
TruCluster Configuration . . . .. . .. . .. . .. . .. . . .. . .. . .. . .. . . .. . .. . .. . .. .
7–7
7.3.1
Repartitioning a Single-Partition AlphaServer
GS80/160/320 as Two Partitions in a Cluster .. . . .. . .. . .. . .. .
7–7
7.4
Determining AlphaServer GS80/160/320 System
Configuration .. . . .. . .. . .. . .. . . .. . .. . .. . .. . .. . . .. . .. . .. . .. . . .. . .. . .. . .. .
7–14
7.5
Updating GS80/160/320 Firmware . .. . .. . . .. . .. . .. . .. . . .. . .. . .. . .. .
7–18
7.5.1
Updating AlphaServer GS80/160/320 Firmware .. . .. . .. . .. .
7–18
8
Configuring a Shared SCSI Bus for Tape Drive Use
8.1
Preparing the TZ88 for Shared Bus Usage . .. . .. . .. . . .. . .. . .. . .. .
8–1
8.1.1
Setting the TZ88N-VA SCSI ID . . .. . . .. . .. . .. . .. . . .. . .. . .. . .. .
8–2
8.1.2
Cabling the TZ88N-VA . .. . .. . .. . .. . .. . . .. . .. . .. . .. . . .. . .. . .. . .. .
8–3
8.1.3
Setting the TZ88N-TA SCSI ID . . .. . . .. . .. . .. . .. . . .. . .. . .. . .. .
8–5
8.1.4
Cabling the TZ88N-TA . .. . .. . .. . .. . .. . . .. . .. . .. . .. . . .. . .. . .. . .. .
8–5
8.2
Preparing the TZ89 for Shared SCSI Usage .. . .. . .. . . .. . .. . .. . .. .
8–6
8.2.1
Setting the DS-TZ89N-VW SCSI ID . .. . .. . .. . .. . . .. . .. . .. . .. .
8–6
Contents vii