Compaq AA-RHGWC-TE - Manual (Page 6)

6.2.2.2 Fabric . . . .. . .. . .. . .. . . .. . .. . .. . .. . .. . . .. . .. . .. . .. . . .. . .. . .. . .. . 6–7
6.2.2.3 Arbitrated Loop Topology . . .. . .. . . .. . .. . .. . .. . . .. . .. . .. . .. . 6–8
6.3 Example Fibre Channel Configurations Supported by
TruCluster Server . . .. . .. . .. . . .. . .. . .. . .. . .. . . .. . .. . .. . .. . . .. . .. . .. . .. .
6–9
6.3.1 Fibre Channel Cluster Configurations for Transparent
Failover Mode . . .. . .. . .. . . .. . .. . .. . .. . .. . . .. . .. . .. . .. . . .. . .. . .. . .. .
6–10
6.3.2 Fibre Channel Cluster Configurations for Multiple-Bus
Failover Mode . . .. . .. . .. . . .. . .. . .. . .. . .. . . .. . .. . .. . .. . . .. . .. . .. . .. .
6–11
6.4 Zoning and Cascaded Switches . . .. . .. . .. . . .. . .. . .. . .. . . .. . .. . .. . .. . 6–14
6.4.1 Zoning . .. . .. . . .. . .. . .. . .. . . .. . .. . .. . .. . .. . . .. . .. . .. . .. . . .. . .. . .. . .. . 6–14
6.4.2 Cascaded Switches . . .. . . .. . .. . .. . .. . .. . . .. . .. . .. . .. . . .. . .. . .. . .. . 6–15
6.5 Installing and Configuring Fibre Channel Hardware . . .. . .. . .. . 6–16
6.5.1 Installing and Setting Up the Fibre Channel Switch .. . .. . 6–16
6.5.1.1 Installing the Switch . . .. . .. . .. . .. . . .. . .. . .. . .. . . .. . .. . .. . .. . 6–17
6.5.1.2 Managing the Fibre Channel Switches . . .. . . .. . .. . .. . .. . 6–18
6.5.1.2.1 Using the Switch Front Panel . . .. . .. . .. . . .. . .. . .. . .. . 6–19
6.5.1.2.2 Setting the Ethernet IP Address and Subnet Mask
from the Front Panel .. . .. . .. . . .. . .. . .. . .. . . .. . .. . .. . .. .
6–19
6.5.1.2.3 Setting the DS-DSGGB-AA and DS-DSGGC-AA
Ethernet IP Address and Subnet Mask from a PC
or Terminal . .. . . .. . .. . .. . .. . .. . . .. . .. . .. . .. . . .. . .. . .. . .. .
6–21
6.5.1.2.4 Logging In to the Switch with a Telnet Connection 6–22
6.5.1.2.5 Setting the Switch Name via Telnet Session . .. . .. . 6–23
6.5.2 Installing and Configuring the KGPSA PCI-to-Fibre
Channel Adapter Module . .. . .. . .. . .. . . .. . .. . .. . .. . . .. . .. . .. . .. .
6–23
6.5.2.1 Installing the KGPSA PCI-to-Fibre Channel Adapter
Module . . .. . .. . .. . .. . . .. . .. . .. . .. . .. . . .. . .. . .. . .. . . .. . .. . .. . .. .
6–23
6.5.2.2 Setting the KGPSA-BC or KGPSA-CA to Run on a
Fabric . . . .. . .. . .. . .. . . .. . .. . .. . .. . .. . . .. . .. . .. . .. . . .. . .. . .. . .. .
6–24
6.5.2.3 Obtaining the Worldwide Names of KGPSA Adapters 6–27
6.5.3 Setting Up the HSG80 Array Controller for Tru64 UNIX
Installation . . .. . .. . .. . .. . . .. . .. . .. . .. . .. . . .. . .. . .. . .. . . .. . .. . .. . .. .
6–28
6.5.3.1 Obtaining the Worldwide Names of HSG80 Controller 6–33
6.6 Installing Tru64 UNIX and TruCluster Server Software Using
Fibre Channel Storage . . .. . . .. . .. . .. . .. . .. . . .. . .. . .. . .. . . .. . .. . .. . .. .
6–34
6.6.1 Before You Install .. . .. . . .. . .. . .. . .. . .. . . .. . .. . .. . .. . . .. . .. . .. . .. . 6–36
6.6.1.1 Configure the HSG80 Storagesets . . .. . .. . .. . . .. . .. . .. . .. . 6–36
6.6.1.2 Adding Units and Identifiers to the HSG80
Storagesets .. . .. . .. . . .. . .. . .. . .. . .. . . .. . .. . .. . .. . . .. . .. . .. . .. .
6–40
6.6.1.3 Set the Device Unit Number . . .. . . .. . .. . .. . .. . . .. . .. . .. . .. . 6–43
6.6.1.4 Displaying the Available Boot Devices .. . .. . . .. . .. . .. . .. . 6–48
6.6.1.5 Set the bootdef_dev Console Environment Variable for
Tru64 UNIX Installation .. . .. . .. . . .. . .. . .. . .. . . .. . .. . .. . .. .
6–49
vi Contents