Rockwell Automation 150 SMC-Flex User Manual - Manual (Page 87)

Programming 4-3
Figure 4.2 Parameter Menu Structure
➀ Depending upon SMC option selected, some parameters may not appear in product display.
➁ Steps back one level.
➂ For further information on parameters, see Appendix B.
➃ For further information on parameter management, see page 4-6.
⑤ See page 4-4 for all SMC-Flex parameters available by the Linear List.
Parameter
0
Metering Basic Overload Jam Comm Masks Language Linear List
Volts Phase A-B SMC Option Overload Class Jam F Lvl Logic Mask Language All parameters
Volts Phase B-C Motor Connection Service Factor Jam F Dly Parameter Mgt ➃ Parameter Mgt ➃ Parameter Mgt ➃
Volts Phase C-A Line Voltage Motor FLC Jam A Lvl
Current Phase A Starting Mode Overload Reset Jam A Dly
DataLinks Motor Data
Current Phase B Ramp Time Overload A Lvl Parameter Mgt ➃
Current Phase C Initial Torque Parameter Mgt ➃ Data In A1 MotorFLC
Watt Meter Cur Limit Lvl
Stall
Data In A2 Motor ID
Kilowatt Hours Kickstart Time
Underload
Data In B1 Parameter Mgt ➃
Elapsed Time Kickstart Lvl Stall Dly Data In B2
Meter Reset Stop Input Underload F Lvl Parameter Mgt ➃ Data In C1
Power Factor Option 1 Input Underload F Dly Data In C2
Mtr Therm Usage Option 2 Input Underload A Lvl
Ground Fault
Data In D1
Motor Speed Stop Mode Underload A Dly Data In D2
Stop Time Parameter Mgt ➃ Gnd Flt Enable Data Out A1
Braking Current Gnd Flt Lvl Data Out A2
Overload Class
Undervoltage
Gnd Flt Dly Data Out B1
Service Factor Gnd Flt Inh Time Data Out B2
Motor FLC Undervolt F Lvl Gnd Flt A Enable Data Out C1
Overload Reset Undervolt F Dly Gnd Flt A Lvl Data Out C2
Aux1 Config Undervolt A Lvl Gnd Flt A Dly Data Out D1
Aux2 Config Undervolt A Dly Parameter Mgt ➃ Data Out D2
Aux3 Config Parameter Mgt ➃ Parameter Mgt ➃
Aux4 Config
PTC
Backspin Timer
Overvoltage
Parameter Mgt ➃ PTC Enable
Overvolt F Lvl Parameter Mgt ➃
Dual Ramp (Option
2 Input = Dual
Ramp) Overvolt F Dly
Overvolt A Lvl
Phase Reversal
Overvolt A Dly
Starting Mode 2 Parameter Mgt ➃ Phase Reversal
Ramp Time 2 Parameter Mtg ➃
Initial Torque 2
Unbalance
Cur Limit Lvl 2
Restart
Kickstart Time 2 Unbalance F Lvl
Kickstart Lvl 2 Unbalance F Dly Starts Per Hour
Parameter Mgt ➃ Unbalance A Lvl Restart Attempts
Unbalance A Dly Restart Dly
Preset SS (Option 2
Input = Preset SS) Parameter Mgt ➃ Parameter Mtg ➃
Slow Speed Sel
Slow Speed Dir
Slow Accel Cur
Slow Running Cur
Parameter Mgt
➃
(Option 2 Input =
Accu-Stop)
Slow Speed Sel
Slow Accel Cur
Slow Running Cur
Braking Current
Stopping Current
Parameter Mgt
➃
Motor
Set Up Utility Linear List ⑤
Protection
Parameter
Monitoring Communications
➀➂ ➁
Esc