Class1 FoamLogix 2.1A & 1.7AHP REV D - Manual (Page 54)

FoamLogix, Model 2.1A and 1.7AHP Class “A”
Electronic Foam Proportioning Systems
54
52 FOAMLOGIX, Model 2.1A Class "A"
Electronic Foam Proportioning System
Installation
ISO 9001 CERTIFIED
FLOW SENSOR CALIBRATION
Verify flow sensor calibration during NFPA/UL
testing of the apparatus and delivery to end user.
IMPORTANT!
AN ACCURATE FLOW MEASURING DEVICE MUST
BE USED TO MEASURE THE WATER FLOW WHEN
CALIBRATING THE FLOW SENSOR. USE A
SUITABLE SIZE, SMOOTH BORE, NOZZLE AND AN
ACCURATE AND CALIBRATED PITOT GAUGE
INSTRUMENT. HAND HELD PITOT GAUGES ARE
USUALLY NOT VERY ACCURATE.
MAKE SURE THE SYSTEM IS CALIBRATED WITH
AN ACCURATE FLOW MEASURING DEVICE.
1. Determine the water flow normally ex-
pected from the discharge outlet and
establish flow.
2. Make sure the water flow established is
within the range of the flow sensor moni-
toring the discharge.
For example, establish a flow rate of 150
GPM (568 LPM) of water through a nozzle
and Pitot system. Compare the calculated
flow value to the value shown on the
control unit display.
Figure 26: Display - Password and Calibration Modes
SELECT DISPLAY
Press and HOLD
Continued to
HOLD
Displayed when
     is pressed
Pressed in
sequence to
enter passwords
Displayed when
     is pressed
Release when
CAL is shown
Figure 27: Display - Flow Sensor Calibration
Figure 26: Display - Password and Calibration Modes
52 FOAMLOGIX, Model 2.1A Class "A"
Electronic Foam Proportioning System
Installation
ISO 9001 CERTIFIED
FLOW SENSOR CALIBRATION
Verify flow sensor calibration during NFPA/UL
testing of the apparatus and delivery to end user.
IMPORTANT!
AN ACCURATE FLOW MEASURING DEVICE MUST
BE USED TO MEASURE THE WATER FLOW WHEN
CALIBRATING THE FLOW SENSOR. USE A
SUITABLE SIZE, SMOOTH BORE, NOZZLE AND AN
ACCURATE AND CALIBRATED PITOT GAUGE
INSTRUMENT. HAND HELD PITOT GAUGES ARE
USUALLY NOT VERY ACCURATE.
MAKE SURE THE SYSTEM IS CALIBRATED WITH
AN ACCURATE FLOW MEASURING DEVICE.
1. Determine the water flow normally ex-
pected from the discharge outlet and
establish flow.
2. Make sure the water flow established is
within the range of the flow sensor moni-
toring the discharge.
For example, establish a flow rate of 150
GPM (568 LPM) of water through a nozzle
and Pitot system. Compare the calculated
flow value to the value shown on the
control unit display.
Figure 26: Display - Password and Calibration Modes
SELECT DISPLAY
Press and HOLD
Continued to
HOLD
Displayed when
     is pressed
Pressed in
sequence to
enter passwords
Displayed when
     is pressed
Release when
CAL is shown
Figure 27: Display - Flow Sensor Calibration
27: Display - Flow Sensor Calibration
FLOW SENSOR CALIBRATION
Verify flow sensor calibration during NFPA/UL testing
of the apparatus and delivery to end user.
IMPORTANT!
AN ACCURATE FLOW MEASURING DEVICE MUST
BE USED TO MEASURE THE WATER FLOW WHEN
CALIBRATING THE FLOW SENSOR. USE A SUITABLE
SIZE, SMOOTH BORE, NOZZLE AND AN ACCURATE
AND CALIBRATED PITOT GAUGE INSTRUMENT.
HAND HELD PITOT GAUGES ARE USUALLY NOT
VERY ACCURATE.
MAKE SURE THE SYSTEM IS CALIBRATED WITH AN
ACCURATE FLOW MEASURING DEVICE.
Determine the water flow normally ex pected 1.
from the discharge outlet and establish flow.
Make sure the water flow established is within 2.
the range of the flow sensor moni toring the
discharge.
For example, establish a flow rate of 150 GPM
(568 LPM) of water through a nozzle and Pitot
system. Compare the calculated flow value to
the value shown on the control unit display.