NORD Drivesystems B1000 - Manual (Page 557)

www.nord.com
DIMENSIONS
D
im
en
si
o
n
s
in
In
ch
es
AL
TERNA
TE SHAFTS SEE P
AGES 682 - 694
D555
G1000 – Subject to Change Without Notice
Solid Input Shaft
Type - W
SK 9012.1 - SK 9086.1
FZ
FW
TAP
FU
FV
CC
KEY
ZB
FZ
FW
TAP
FU
FV
CC
KEY
ZB
SK 9092.1 - SK 9096.1
Unit CC ZB FW FV FU FZ TAP KEY Unit Dimensions
SK 9012.1 4.73 --- 0.28 1.50 0.625 +0.0000 0.70 1/4-20 3 / 16 x 3 / 16 x 1 1 / 4  564
-0.0005
SK 9013.1 4.73 --- 0.28 1.50 0.625 +0.0000 0.70 1/4-20 3 / 16 x 3 / 16 x 1 1 / 4  570
-0.0005
SK 9016.1 4.73 --- 0.28 1.50 0.625 +0.0000 0.70 1/4-20 3 / 16 x 3 / 16 x 1 1 / 4  576
-0.0005
SK 9017.1 4.73 --- 0.28 1.50 0.625 +0.0000 0.70 1/4-20 3 / 16 x 3 / 16 x 1 1 / 4  582
-0.0005
SK 9022.1 4.73 --- 0.28 1.50 0.625 +0.0000 0.70 1/4-20 3 / 16 x 3 / 16 x 1 1 / 4  588
-0.0005
SK 9023.1 4.73 --- 0.28 1.50 0.625 +0.0000 0.70 1/4-20 3 / 16 x 3 / 16 x 1 1 / 4  594
-0.0005
SK 9032.1 6.80 --- 0.31 2.00 0.875 +0.0000 0.96 1/4-20 3 / 16 x 3 / 16 x 1 5 / 8  600
-0.0005
SK 9033.1 4.73 --- 0.28 1.50 0.625 +0.0000 0.70 1/4-20 3 / 16 x 3 / 16 x 1 1 / 4  606
-0.0005
SK 9042.1 8.36 --- 0.31 3.12 1.500 +0.0000 1.66 5/8-11 3 / 8 x 3 / 8 x 2 1 / 2  612
-0.0005
SK 9043.1 6.80 --- 0.31 2.00 0.875 +0.0000 0.96 1/4-20 3 / 16 x 3 / 16 x 1 5 / 8  618
-0.0005
SK 9052.1 8.36 --- 0.31 3.12 1.500 +0.0000 1.66 5/8-11 3 / 8 x 3 / 8 x 2 1 / 2  624
-0.0005
SK 9053.1 6.80 --- 0.31 2.00 0.875 +0.0000 0.96 1/4-20 3 / 16 x 3 / 16 x 1 5 / 8  630
-0.0005
SK 9072.1 11.38 0.98 0.31 4.38 1.625 +0.0000 1.79 5/8-11 3 / 8 x 3 / 8 x 3 5 / 8  636
-0.0005
SK 9072.1/32 6.80 1.38 0.31 2.00 0.875 +0.0000 0.96 1/4-20 3 / 16 x 3 / 16 x 1 5 / 8  666
-0.0005
SK 9072.1/42 8.36 1.38 0.31 3.12 1.500 +0.0000 1.66 5/8-11 3 / 8 x 3 / 8 x 2 1 / 2  666
-0.0005
SK 9082.1 15.61 1.65 0.47 5.50 2.500 +0.0000 2.77 3/4-10 5 / 8 x 5 / 8 x 4 5 / 8  642
-0.0010
SK 9082.1/42 8.36 0.98 0.31 3.12 1.500 +0.0000 1.66 5/8-11 3 / 8 x 3 / 8 x 2 1 / 2  666
-0.0005
SK 9082.1/52 8.36 0.98 0.31 3.12 1.500 +0.0000 1.66 5/8-11 3 / 8 x 3 / 8 x 2 1 / 2  666
-0.0005
SK 9086.1 15.61 0.98 0.47 5.50 2.500 +0.0000 2.77 3/4-10 5 / 8 x 5 / 8 x 4 5 / 8  648
-0.0010
SK 9086.1/52 8.36 0.98 0.31 3.12 1.500 +0.0000 1.66 5/8-11 3 / 8 x 3 / 8 x 2 1 / 2  666
-0.0005
SK 9092.1 15.61 1.65 0.47 5.50 2.500 +0.0000 2.77 3/4-10 5 / 8 x 5 / 8 x 4 5 / 8  654
-0.0010
SK 9092.1/52 8.36 1.26 0.31 3.12 1.500 +0.0000 1.66 5/8-11 3 / 8 x 3 / 8 x 2 1 / 2  666
-0.0005
SK 9096.1 9.96 1.30 0.51 5.51 2.750 +0.0000 3.03 3/4-10 5 / 8 x 5 / 8 x 4 5 / 8  660
-0.0010
SK 9096.1/62 11.38 1.97 0.31 4.38 1.625 +0.0000 1.79 5/8-11 3 / 8 x 3 / 8 x 3 5 / 8  667
-0.0005
SK 9096.1/63 8.36 0.94 0.31 3.12 1.500 +0.0000 1.66 5/8-11 3 / 8 x 3 / 8 x 2 1 / 2  667
-0.0005