NORD Drivesystems B1000 - Manual (Page 19)

www.nord.com A17 G1000 – Subject to Change Without Notice
INTRODUCTION
Mounting Position Cross Reference Table (old to new)
Helical Gear Units
(In-line)
Parallel Shaft Gear Units
(Clincher™)
Helical-bevel Gear Units Helical-worm Gear Units
Old New Old New Old New Old New
B3 M1 H1 M1 B3 M1 B3 M1
B5 M1 H2 M3 B3I M4 B3I M4
B5I M3 H3 M6 B5 M2 B5 M2
B5II M5 H4 M5 B5I M1 B5I M1
B5III M6 H5 M4 B5II M4 B5II M4
B6 M5 H6 M2 B5III M3 B5III M3
B7 M6 B6 M2 B6 M2
B8 M3 B6I M1 B6I M1
V1 M4 B6II M4 B6II M4
V3 M2 B8 M3 B8 M3
V5 M4 B8I M2 B8I M2
V6 M2 H1 M1 H1 M1
H2 M3 H2 M3
H3 M4 H3 M4
H4 M2 H4 M2
H5 M5 H5 M5
H6 M6 H6 M6
V1 M5 V1 M5
V3 M6 V3 M6
V5 M5 V5 M5
V5I M5 V5I M5
V6 M6 V6 M6
V6I M6 V6I M6
Mounting Position Cross Reference Table (new to old)
Helical Gear Units
(In-line)
Parallel Shaft Gear Units
(Clincher™)
Helical-bevel Gear Units Helical-worm Gear Units
New Old New Old New Old New Old
M1 B3, B5 M1 H1 M1 B3, B5I, B6I, H1 M1 B3, B5I, B6I, H1
M2 V3, V6 M2 H6 M2 B5, B6, B8I, H4 M2 B5, B6, B8I, H4
M3 B5I, B8 M3 H2 M3 B5III, B8, H2 M3 B5III, B8, H2
M4 V1, V5 M4 H5 M4 B3I, B5II, B6II, H3 M4 B3I, B5II, B6II, H3
M5 B5II, B6 M5 H4 M5 H5, V1, V5, V5I M5 H5, V1, V5, V5I
M6 B5III, B7 M6 H3 M6 H6, V3, V6, V6I M6 H6, V3, V6, V6I
Mounting Positions
The reducer mounting position determines the
approximate oil fi ll level and the appropriate vent
location. In some cases mounting position may dictate
possible variation in fi nal reducer assembly. If consid-
ering any mounting positions that are not shown as
catalog standard options, it is critical that the customer
consult with NORD prior to ordering.
New Mounting Position System
NORD is in the processes of changing mounting posi-
tion systems. Historically the NORD mounting position
system was based on international motor standards.
NORD is changing in an effort to simplify the system.
The new system is based on the six sides of a cube.
Below is a cross reference between the old and new
mounting position codes.
Mounting
Positions