Document Outline

• HP SureStore 1200mx / 2200mx Optical Jukebox
  • HP SureStore 1200mx / 2200mx Optical Jukebox
    • HP SureStore 1200mx / 2200mx Optical Jukebox
    • User’s Guide
    • Edition 1
    • HP Part No. C1104-90021
    • Printed in: Greeley, CO USA
      • Printed in: Greeley, CO USA
    • © Copyright August 2000
      • © Copyright August 2000
  • Notice
    • Notice
    • This document contains information that is protected by copyright. All rights are reserved. No pa...
    • Hewlett-Packard makes no warranty of any kind with regard to this printed material, including, bu...
    • © Copyright August 2000
      • © Copyright August 2000
  • Printing History
    • Printing History
    • New editions of this manual incorporate all material updated since the previous edition. The manu...
  • Typographical Conventions
    • Typographical Conventions
    • The following typographical conventions are used in this manual:
    • Emphasis
      • Emphasis
    • Keycap
      • Keycap
    • Computer Output
      • Computer Output
        • Computer Output
    • WARNING Warnings call attention to a procedure or practice that could result in personal injury i...
      • WARNING Warnings call attention to a procedure or practice that could result in personal injury i...
    • CAUTION Cautions call attention to an operating procedure or practice that could damage the produ...
      • CAUTION Cautions call attention to an operating procedure or practice that could damage the produ...
    • NOTE Notes provide information that can be helpful in understanding the operation of the product.
      • NOTE Notes provide information that can be helpful in understanding the operation of the product.
  • In This Manual
    • In This Manual
    • This user’s guide includes:
    • Chapter 1
      • Chapter 1
        • Chapter 1
        • set-up information for this optical jukebox
          • set-up information for this optical jukebox
      • Chapter 2
        • Chapter 2
        • information about choosing and using optical disks
          • information about choosing and using optical disks
      • Chapter 3
        • Chapter 3
        • features description, operating instructions, and troubleshooting information
          • features description, operating instructions, and troubleshooting information
      • Appendix A
        • Appendix A
        • supplies and customer support
          • supplies and customer support
      • Appendix B
        • Appendix B
        • operating this jukebox on a SCSI bus
          • operating this jukebox on a SCSI bus
      • Appendix C
        • Appendix C
        • safety and regulatory information
          • safety and regulatory information
    • Glossary of Terms
    • Index
• 1 Setting Up the Jukebox
  • 1 Setting Up the Jukebox
  • Overview of This Chapter
    • Overview of This Chapter
    • This chapter gives information about the following topics:
    • • right side panel features
      • • right side panel features
        • • right side panel features
        • connecting SCSI and power cords
    • • moving or shipping the jukebox
      • • moving or shipping the jukebox
        • • moving or shipping the jukebox
    • • connecting SCSI and power cords
      • • connecting SCSI and power cords
        • • connecting SCSI and power cords
    • setting up:items included
      • setting up:items included
        • setting up:items included
        • setting up:items not included
      • Items included with the jukebox:
      • • power cord
        • • power cord
          • • power cord
        • • single-ended and differential SCSI terminators
          • • single-ended and differential SCSI terminators
          • - one of each included in a 4- or 6-drive jukebox
            • - one of each included in a 4- or 6-drive jukebox
              • - one of each included in a 4- or 6-drive jukebox
            • - two of each included in a 10-drive jukebox
              • - two of each included in a 10-drive jukebox
            • - this guide
              • - this guide
      • Items needed but not included with the jukebox:
      • • SCSI cable with either a high-density 50-pin (Micro D) or high-density 68-pin (Micro D) connect...
        • • SCSI cable with either a high-density 50-pin (Micro D) or high-density 68-pin (Micro D) connect...
          • • SCSI cable with either a high-density 50-pin (Micro D) or high-density 68-pin (Micro D) connect...
        • • single-ended or differential SCSI host adapter with at least one available address. If you have...
          • • single-ended or differential SCSI host adapter with at least one available address. If you have...
        • • application software that supports this type of jukebox
          • • application software that supports this type of jukebox
  • system components needed
    • system components needed
      • system components needed
    • This jukebox requires application software to operate it as a single storage device composed of m...
    • Standard Configuration
      • Standard Configuration
    • The following list is a hierarchy of the system components needed to operate this jukebox in a st...
    • • Host computer CPU
      • • Host computer CPU
        • • Host computer CPU
      • • Operating system
        • • Operating system
      • • Optical jukebox application software
        • • Optical jukebox application software
      • • Jukebox SCSI drivers (may be included in optical jukebox application software above)
        • • Jukebox SCSI drivers (may be included in optical jukebox application software above)
      • • Jukebox
        • • Jukebox
    • High-Availability Configuration
      • High-Availability Configuration
    • The following list is a hierarchy of the system components needed to operate this jukebox in a hi...
    • • Host computer CPUs (two host computers)
      • • Host computer CPUs (two host computers)
        • • Host computer CPUs (two host computers)
      • • Operating systems (on two host computers)
        • • Operating systems (on two host computers)
      • • High-availability application software (links both host computers)
        • • High-availability application software (links both host computers)
      • • Optical jukebox application software (on both host computers)
        • • Optical jukebox application software (on both host computers)
      • • Jukebox SCSI drivers (may be included in optical jukebox application software above)
        • • Jukebox SCSI drivers (may be included in optical jukebox application software above)
      • • Jukebox
        • • Jukebox
  • Identifying Right-Side Panel Features
    • Identifying Right-Side Panel Features
    • Figure 1-1 Right-Side Panel Features — 10-Drive Jukebox Shown
      • Figure 1-1 Right-Side Panel Features — 10-Drive Jukebox Shown
    • The numbers below correspond to the numbers in Figure 1-1 on the previous page
    • • 1
      • Active bus indicator
        • SCSI interface:active bus indicator
        • active bus indicator
      • Lit when the SCSI bus is active. There is an indicator for each single-ended and each differentia...
      • 2
      • SCSI interface selection switch
        • SCSI interface:interface selection switch
        • interface selection switch
      • Used to select either a single-ended or differential SCSI interface on the SCSI interface board.
        • Used to select either a single-ended or differential SCSI interface on the SCSI interface board.
        • In 4- or 6-drive jukeboxes, there is one interface board. In 10-drive jukeboxes, there are two in...
      • 3
      • SCSI ports
        • SCSI interface:ports
      • Used for connecting SCSI cables to the interface board. The interface board has two types of inte...
        • Used for connecting SCSI cables to the interface board. The interface board has two
      • 4
      • Power cord strain relief clip
        • strain relief clip
      • Used to route the power cord away from other connectors and provide strain relief for the power c...
        • Used to route the power cord away from other connectors and provide strain relief for the power c...
      • 5
      • Product serial number label
        • serial number location
      • Needed for service calls. Write down your jukebox serial number before you call your service repr...
        • Needed for service calls. Write down your jukebox serial number before you call your service repr...
      • 6
      • Access panel and mounting screws
        • access panel:location
        • access panel:mounting screws
      • Panel that covers the interface and power connection components. The panel is secured by two scre...
        • Panel that covers the interface and power connection components. The panel is secured by two scre...
      • Continued on the next page
      • 7
      • Cable access hole
        • cable access hole
      • Used to pass SCSI and power cables through to the inside of the jukebox.
        • Used to pass SCSI and power cables through to the inside of the jukebox.
      • 8
      • Power switch
        • power switch
        • switch:power
      • The power switch is under the panel but can be operated through the hole in the panel. Turns powe...
        • The power switch is under the panel but can be operated through the hole in the panel. Turns powe...
      • 9
      • Power receptacle
        • power receptacle
      • Receptacle for the jukebox power cord. Located on the bottom of the power distribution assembly.
        • Receptacle for the jukebox power cord. Located on the bottom of the power distribution assembly.
      NOTE Two screws secure the customer access panel to the side of jukebox during shipment from the ...

      • NOTE Two screws secure the customer access panel to the side of jukebox during shipment from the ...
      SCSI cables:connecting

      • SCSI cables:connecting
        • SCSI cables:connecting
        • connecting SCSI cables
      • In all configurations, the following cabling capabilities apply:
      • Interface types available
      • Single-ended or differential SCSI, selected by the interface selection switch on each interface card
        • Single-ended or differential SCSI, selected by the interface selection switch on each interface card
      • Number of interface cards available
      • One card in 4- and 6-drive models, two cards in 10-drive models
        • One card in 4- and 6-drive models, two cards in 10-drive models
      • Number of hosts
      • This jukebox may be used in high availability environments. High availability environments can be...
        • This jukebox may be used in high availability environments. High availability environments can be...
          • This jukebox may be used in high availability environments. High availability environments can be...
      SCSI cables:maximum length

      • SCSI cables:maximum length
      • maximum cable length
      Table 1-1 Maximum SCSI External Cable Lengths (Assuming no devices internal to the host computer)

      • Table 1-1 Maximum SCSI External Cable Lengths (Assuming no devices internal to the host computer)
      • Interface Type
      • Maximum External Cable Length
      • Single-Ended SCSI (50-pin high-density connector)
      • 3 meters (9.8 feet)
      • Differential SCSI (68-pin high-density connector)
      • 25 meters (82.0 feet)
      NOTE Hewlett-Packard recommends that you use SCSI cables with thumbscrew connectors. Clip type ca...

      • NOTE Hewlett-Packard recommends that you use SCSI cables with thumbscrew connectors. Clip type ca...
      Choosing Your cabling Configuration

      • Choosing Your cabling Configuration
      • Pick the configuration that applies to your plans below. You will be shown the page for the prope...
      • See page
        • See page
      • Standard Configuration
        • Standard Configuration
      • • The only peripheral on a bus
      • ... and the jukebox has 4 or 6 drives
      • 1-9
      • ... and the jukebox has 10 drives and you are using two host adapters
      • 1-12
      • ... and the jukebox has 10 drives and you are using one host adapter
      • 1-14
      • • The jukebox will share a bus with other devices
      • 1-16
      • High Availability configuration
        • High Availability configuration
      • • Consult with your high-availability vendor
      • —
      connecting:4- or 6-drive jukebox

      • connecting:4- or 6-drive jukebox
        • connecting:4- or 6-drive jukebox
      • CAUTION Make sure that all peripheral devices connected to the host computer have been properly s...
        • CAUTION Make sure that all peripheral devices connected to the host computer have been properly s...
      • Removing the Customer Access Panel
        • Removing the Customer Access Panel
        • 1. Switch off power to the host computer before you connect the jukebox
          • 1. Switch off power to the host computer before you connect the jukebox
            • 1. Switch off power to the host computer before you connect the jukebox
            • NOTE The jukebox ships from the factory with two screws securing the bottom of the customer acces...
              • NOTE The jukebox ships from the factory with two screws securing the bottom of the customer acces...
              • These screws may not have been replaced.
              • It is a good idea to use the screws to secure the access panel to the jukebox since they must be ...
              • If you have to replace these screws, they are 6/32 x .437.
          • 2. Remove the customer access panel by pulling on the bottom of the panel and then lifting it off...
            • 2. Remove the customer access panel by pulling on the bottom of the panel and then lifting it off...
        • Refer to the following diagram in the next steps.
          • Refer to the following diagram in the next steps.
        • 3. Select single-ended (“A”) or differential (“B”) interface using the SCSI interface selection s...
          • 3. Select single-ended (“A”) or differential (“B”) interface using the SCSI interface selection s...
            • 3. Select single-ended (“A”) or differential (“B”) interface using the SCSI interface selection s...
            • The diagram shows connecting a cable to the differential (“B”) interface.
          • 4. Connect a cable between your host computer and either port of the jukebox SCSI connectors of y...
            • 4. Connect a cable between your host computer and either port of the jukebox SCSI connectors of y...
            • Route the cable through the slot at the bottom of the right side (“C”).
          • 5. Plug a SCSI terminator into the unused SCSI port of interface type you chose (the example diag...
            • 5. Plug a SCSI terminator into the unused SCSI port of interface type you chose (the example diag...
            • If you are using the differential interface, use a 68-pin high-density terminator. If you are usi...
            • Figure 1-2 Connecting a 4- or 6-Drive Jukebox
              • Figure 1-2 Connecting a 4- or 6-Drive Jukebox
          • 6. Plug a SCSI terminator into one of the SCSI ports on the unused interface. Only one terminator...
            • 6. Plug a SCSI terminator into one of the SCSI ports on the unused interface. Only one terminator...
            • The example diagram shows the terminator on the single-ended interface connector “A2” but the ter...
            • Use an active terminator if you are terminating a single-ended interface.
            • If you are terminating a differential interface, use a 68-pin high-density terminator. If you are...
          • 7. To continue with the installation, go to “Connecting Power” in this Chapter.
            • 7. To continue with the installation, go to “Connecting Power” in this Chapter.
      connecting:10-drive jukebox, two host adapters

      • connecting:10-drive jukebox, two host adapters
        • connecting:10-drive jukebox, two host adapters
      • CAUTION Make sure that all peripheral devices connected to the host computer have been properly s...
        • CAUTION Make sure that all peripheral devices connected to the host computer have been properly s...
      • Removing the Customer Access Panel
        • Removing the Customer Access Panel
        • 1. Switch off power to the host computer before you connect the jukebox.
          • 1. Switch off power to the host computer before you connect the jukebox.
            • 1. Switch off power to the host computer before you connect the jukebox.
            • NOTE The jukebox ships from the factory with two screws securing the bottom of the customer acces...
              • NOTE The jukebox ships from the factory with two screws securing the bottom of the customer acces...
              • These screws may not have been replaced.
              • It is a good idea to use the screws to secure the access panel to the jukebox since they must be ...
              • If you have to replace these screws, they are 6/32 x .437.
        • Refer to the following diagram in the next steps.
          • Refer to the following diagram in the next steps.
        • 2. Select single-ended (“A”) or differential (“B”) interface using the SCSI interface selection s...
          • 2. Select single-ended (“A”) or differential (“B”) interface using the SCSI interface selection s...
            • 2. Select single-ended (“A”) or differential (“B”) interface using the SCSI interface selection s...
            • The diagram shows connecting a cable to the differential (“B”) interface.
          • 3. Connect cables between the two host adapters on your host computer and two SCSI interfaces on ...
            • 3. Connect cables between the two host adapters on your host computer and two SCSI interfaces on ...
            • You can connect the two cables to two interfaces of the same type of different types (single-ende...
            • The diagram shows cable connections to the differential SCSI interface on both interface cards at...
            • Route the cables through the slot at the bottom of the right side (C).
          • 4. Remove the customer access panel by pulling on the bottom of the panel and then lifting it off...
            • 4. Remove the customer access panel by pulling on the bottom of the panel and then lifting it off...
            • Figure 1-3 Connecting a 10-Drive Jukebox, Two Host Adapters, Basic SCSI Addressing
              • Figure 1-3 Connecting a 10-Drive Jukebox, Two Host Adapters, Basic SCSI Addressing
        • 5. Plug a SCSI terminator into the unused SCSI connector of interface type you chose (the example...
          • 5. Plug a SCSI terminator into the unused SCSI connector of interface type you chose (the example...
            • 5. Plug a SCSI terminator into the unused SCSI connector of interface type you chose (the example...
            • If you are using the differential interface, use a 68-pin high-density terminator. If you are usi...
          • 6. Plug a SCSI terminator into one of SCSI ports on each unused interface (the example diagram sh...
            • 6. Plug a SCSI terminator into one of SCSI ports on each unused interface (the example diagram sh...
            • Use a 50-pin high-density terminator for the single-ended interface or a 68-pin terminator for th...
          • 7. To continue with the installation, go to “Connecting Power” in this Chapter.
            • 7. To continue with the installation, go to “Connecting Power” in this Chapter.
      connecting:10-drive jukebox, one host adapter

      • connecting:10-drive jukebox, one host adapter
        • connecting:10-drive jukebox, one host adapter
      • CAUTION Make sure that all peripheral devices connected to the host computer have been properly s...
        • CAUTION Make sure that all peripheral devices connected to the host computer have been properly s...
      • Removing the Customer Access Panel
        • Removing the Customer Access Panel
        • 1. Switch off power to the host computer before you connect the jukebox.
          • 1. Switch off power to the host computer before you connect the jukebox.
            • 1. Switch off power to the host computer before you connect the jukebox.
            • NOTE The jukebox ships from the factory with two screws securing the bottom of the customer acces...
              • NOTE The jukebox ships from the factory with two screws securing the bottom of the customer acces...
              • These screws may not have been replaced.
              • It is a good idea to use the screws to secure the access panel to the jukebox since they must be ...
              • If you have to replace these screws, they are 6/32 x .437.
          • 2. Remove the customer access panel by pulling on the bottom of the panel and then lifting it off...
            • 2. Remove the customer access panel by pulling on the bottom of the panel and then lifting it off...
        • Refer to the following diagram in the notes steps.
          • Refer to the following diagram in the notes steps.
        • 3. Select single-ended (“A”) or differential (“B”) interface using the SCSI interface selection s...
          • 3. Select single-ended (“A”) or differential (“B”) interface using the SCSI interface selection s...
            • 3. Select single-ended (“A”) or differential (“B”) interface using the SCSI interface selection s...
            • The diagram shows connecting the host computer cable to a differential interface port (“B3”). Thi...
            • Route the cable through the slot at the bottom of the right side.
          • 4. Connect a short cable between the interface card you have chosen to the other Bus (the example...
            • 4. Connect a short cable between the interface card you have chosen to the other Bus (the example...
        • Figure 1-4 Connecting a 10-Drive Jukebox, One Host Adapter, Bus 1 and 2 Daisy-Chained, LUN Addres...
          • Figure 1-4 Connecting a 10-Drive Jukebox, One Host Adapter, Bus 1 and 2 Daisy-Chained, LUN Addres...
        • 5. Terminate the daisy-chained bus by plugging a terminator into the unused port of the second in...
          • 5. Terminate the daisy-chained bus by plugging a terminator into the unused port of the second in...
            • 5. Terminate the daisy-chained bus by plugging a terminator into the unused port of the second in...
            • A differential interface port uses a 68-pin high-density terminator. A single-ended interface por...
            • The same cabling can be done using the single-ended ports.
            • CAUTION Do not daisy-chain between single-ended and differential interfaces.
              • CAUTION Do not daisy-chain between single-ended and differential interfaces.
        • 6. Plug a SCSI terminator into one of SCSI ports on each unused interface (the example diagram sh...
          • 6. Plug a SCSI terminator into one of SCSI ports on each unused interface (the example diagram sh...
            • 6. Plug a SCSI terminator into one of SCSI ports on each unused interface (the example diagram sh...
            • Use a 50-pin high-density active terminator for the single-ended interface or a 68-pin terminator...
          • 7. To continue with the installation, go to “Connecting Power” in this Chapter.
            • 7. To continue with the installation, go to “Connecting Power” in this Chapter.
      connecting:with other devices on the bus

      • connecting:with other devices on the bus
        • connecting:with other devices on the bus
      • NOTE Operating this jukebox with other peripherals on the same bus is supported, but not recommen...
        • NOTE Operating this jukebox with other peripherals on the same bus is supported, but not recommen...
      • In most circumstances, the recommended configuration for this jukebox is as the only device on a ...
      • It is possible to connect this jukebox on a bus with additional peripherals in many different way...
      • • a 4- or 6-drive jukebox using basic SCSI addressing or Logical Unit Numbering (LUN) addressing
        • • a 4- or 6-drive jukebox using basic SCSI addressing or Logical Unit Numbering (LUN) addressing
          • • a 4- or 6-drive jukebox using basic SCSI addressing or Logical Unit Numbering (LUN) addressing
        • • a 10-drive jukebox with one host adapter and with LUN addressing, daisy-chaining Bus 1 and Bus ...
          • • a 10-drive jukebox with one host adapter and with LUN addressing, daisy-chaining Bus 1 and Bus ...
        • • a 10-drive jukebox with two host adapters and using LUN addressing
          • • a 10-drive jukebox with two host adapters and using LUN addressing
      • There are many issues that must be considered when connecting other devices on a bus with this ju...
      • • how the jukebox is used; archiving, backup, near-line storage. What performance must be maintained
        • • how the jukebox is used; archiving, backup, near-line storage. What performance must be maintained
          • • how the jukebox is used; archiving, backup, near-line storage. What performance must be maintained
        • • how the additional peripheral will be used. How much demand will it place on the bus
          • • how the additional peripheral will be used. How much demand will it place on the bus
        • • whether you will be mixing “wide” and “narrow” devices on the bus.
          • • whether you will be mixing “wide” and “narrow” devices on the bus.
        • • whether you are using both internal and external segments on your SCSI host adapter
          • • whether you are using both internal and external segments on your SCSI host adapter
        • • whether your bus is single-ended or differential
          • • whether your bus is single-ended or differential
      • NOTE Appendix B provides a brief overview of SCSI and the issues you must consider when placing o...
        • NOTE Appendix B provides a brief overview of SCSI and the issues you must consider when placing o...
      connecting:power

      • connecting:power
        • connecting:power
      • 1. Ensure that the power switch on the jukebox is OFF (“5” on Figure 1-1)
        • 1. Ensure that the power switch on the jukebox is OFF (“5” on Figure 1-1)
          • 1. Ensure that the power switch on the jukebox is OFF (“5” on Figure 1-1)
      • NOTE Use the power cord shipped with the jukebox.
        • NOTE Use the power cord shipped with the jukebox.
      • 2. Route the power cord through the strain relief clip (“4” on Figure 1-1) and close the clip snu...
        • 2. Route the power cord through the strain relief clip (“4” on Figure 1-1) and close the clip snu...
          • 2. Route the power cord through the strain relief clip (“4” on Figure 1-1) and close the clip snu...
        • 3. Plug the socket end of the power cord into the power port on bottom of the power distribution ...
          • 3. Plug the socket end of the power cord into the power port on bottom of the power distribution ...
        • 4. Continue to route the power cable down, through the long cable slot at the bottom of the jukeb...
          • 4. Continue to route the power cable down, through the long cable slot at the bottom of the jukeb...
        • 5. Plug the other end of the power cord into a three-hole grounded outlet.
          • 5. Plug the other end of the power cord into a three-hole grounded outlet.
        • 6. Press the power switch ON (“8” on Figure 1-1)
          • 6. Press the power switch ON (“8” on Figure 1-1)
          • When power is applied, TESTING and NOT READY alternately display. Once the poweron test completes...
      • NOTE If DEVICE FAILED displays. See “Troubleshooting” in Chapter 3 for troubleshooting procedures.
        • NOTE If DEVICE FAILED displays. See “Troubleshooting” in Chapter 3 for troubleshooting procedures.
      • 7. Refer to Chapter 3, “Operating the Jukebox” for instructions on setting the SCSI addresses, lo...
        • 7. Refer to Chapter 3, “Operating the Jukebox” for instructions on setting the SCSI addresses, lo...
          • 7. Refer to Chapter 3, “Operating the Jukebox” for instructions on setting the SCSI addresses, lo...
      • NOTE Continue on to “Configuring Write Verify” on the next page.
        • NOTE Continue on to “Configuring Write Verify” on the next page.
      configuring write verify

      • configuring write verify
        • configuring write verify
        • write verify
      • The write verify configuration ensures that data is written reliably to an optical disk. The juke...
      • Writing data on a magneto-optical disk requires two passes. The first pass erases the data in the...
      • When write verify is configured to ON, an additional pass is made over the sector. This third pas...
      • If you choose to change the write verify configuration to OFF, refer to “Configuring Operating Co...
      • NOTE Continue on to “Installing the Wheel Chocks ” on the next page.
        • NOTE Continue on to “Installing the Wheel Chocks ” on the next page.
      wheel chocks

      • wheel chocks
        • wheel chocks
        • installing the wheel chocks
        • chocks
      • WARNING This jukebox rolls easily and could cause injury or damage if allowed to move unintention...
        • WARNING This jukebox rolls easily and could cause injury or damage if allowed to move unintention...
        • Four wheel chocks are provided to stabilize the jukebox in position. Install the wheel chocks aft...
      • Figure 1-5 Installing the Wheel Chocks
        • Figure 1-5 Installing the Wheel Chocks
      • 1. After all cables and panels are mounted, roll the unit to its final position.
        • 1. After all cables and panels are mounted, roll the unit to its final position.
          • 1. After all cables and panels are mounted, roll the unit to its final position.
        • 2. Spread the chock apart slightly and slide it around the bottom of the wheel as shown on the le...
          • 2. Spread the chock apart slightly and slide it around the bottom of the wheel as shown on the le...
        • 3. Repeat Step 2 for the remaining three wheels.
          • 3. Repeat Step 2 for the remaining three wheels.
      • NOTE This is the last step in the physical installation.
        • NOTE This is the last step in the physical installation.
      Moving or Shipping the Jukebox

      • Moving or Shipping the Jukebox
      • Refer to the following two sections if you want to move or ship the optical jukebox. If you want ...
      • moving the jukebox
        • moving the jukebox
          • moving the jukebox
        • 1. If you will be removing the disks from the jukebox, follow your jukebox application software i...
          • 1. If you will be removing the disks from the jukebox, follow your jukebox application software i...
            • 1. If you will be removing the disks from the jukebox, follow your jukebox application software i...
            • Ensure that there are no disks in the drives.
            • If you will be manually ejecting disks, refer to “Ejecting an Optical Disk From the Jukebox” in C...
            • CAUTION Failure to eject a disk from the optical drive prior to moving the jukebox could result i...
              • CAUTION Failure to eject a disk from the optical drive prior to moving the jukebox could result i...
            • CAUTION Turning off the jukebox in the next step could cause data loss if not done correctly.
              • CAUTION Turning off the jukebox in the next step could cause data loss if not done correctly.
              • Do not turn off power to the jukebox until you are sure the SCSI bus is inactive. Removing power ...
        • 2. Switch jukebox power OFF (“8” on Figure 1-1).
          • 2. Switch jukebox power OFF (“8” on Figure 1-1).
            • 2. Switch jukebox power OFF (“8” on Figure 1-1).
          • 3. Remove the right side lower access panel by pulling on the bottom of the panel and then liftin...
            • 3. Remove the right side lower access panel by pulling on the bottom of the panel and then liftin...
            • If screws are installed on the bottom corners of the panel, use a flatblade screwdriver or T-15 T...
          • 4. Remove the power cord and the SCSI cable connections.
            • 4. Remove the power cord and the SCSI cable connections.
          • 5. Loosen the 1/2-inch nut securing the leveler feet and screw the feet up to raise them away fro...
            • 5. Loosen the 1/2-inch nut securing the leveler feet and screw the feet up to raise them away fro...
          • 6. Remove the chocks from the four castor wheels on the bottom of the jukebox (Figure 1-5).
            • 6. Remove the chocks from the four castor wheels on the bottom of the jukebox (Figure 1-5).
        • WARNING Push the jukebox only from the right or left sides (see Figure 1-1). Pushing the jukebox ...
          • WARNING Push the jukebox only from the right or left sides (see Figure 1-1). Pushing the jukebox ...
        • 7. Carefully move the jukebox to its new destination.
          • 7. Carefully move the jukebox to its new destination.
            • 7. Carefully move the jukebox to its new destination.
          • 8. Set up the jukebox at its new location. Refer to the cabling and addressing information in the...
            • 8. Set up the jukebox at its new location. Refer to the cabling and addressing information in the...
          • 9. Lower the leveler feet and tighten the 1/2-inch nut on each foot.
            • 9. Lower the leveler feet and tighten the 1/2-inch nut on each foot.
          • 10. Place the wheel chocks around the four caster wheels (Figure 1-5).
            • 10. Place the wheel chocks around the four caster wheels (Figure 1-5).
          • 11. Bring the jukebox online according to your system’s requirements.
            • 11. Bring the jukebox online according to your system’s requirements.
      • shipping the jukebox
        • shipping the jukebox
          • shipping the jukebox
        • 1. Follow your jukebox application software instructions for unmounting and ejecting disks.
          • 1. Follow your jukebox application software instructions for unmounting and ejecting disks.
            • 1. Follow your jukebox application software instructions for unmounting and ejecting disks.
            • Ensure that there are no disks in the drives.
            • If you will be manually ejecting disks, refer to “Ejecting a Disk From the Jukebox in Chapter 3.
            • CAUTION Failure to eject a disk from the optical drive prior to moving the jukebox could result i...
              • CAUTION Failure to eject a disk from the optical drive prior to moving the jukebox could result i...
              • Failure to remove all disks from the storage slots in the jukebox could result in damage to the j...
          • 2. Follow your jukebox application’s instructions for labeling the disks according to what you wi...
            • 2. Follow your jukebox application’s instructions for labeling the disks according to what you wi...
            • CAUTION Turning off the jukebox in the next step could cause data loss if not done correctly.
              • CAUTION Turning off the jukebox in the next step could cause data loss if not done correctly.
              • Do not turn off power to the jukebox until you are sure the SCSI bus is inactive. Removing power ...
          • 3. Switch jukebox power OFF (“8” on Figure 1-1).
            • 3. Switch jukebox power OFF (“8” on Figure 1-1).
          • 4. Remove the right side lower access panel by pulling on the bottom of the panel and then liftin...
            • 4. Remove the right side lower access panel by pulling on the bottom of the panel and then liftin...
            • If screws are installed on the bottom corners of the panel, use a flatblade screwdriver or T-15 T...
          • 5. Remove the power cord and the SCSI cable connections.
            • 5. Remove the power cord and the SCSI cable connections.
          • 6. Loosen the 1/2-inch nut securing each leveler foot and screw the four feet up to raise them aw...
            • 6. Loosen the 1/2-inch nut securing each leveler foot and screw the four feet up to raise them aw...
          • 7. Remove the chocks from the four caster wheels on the bottom of the jukebox.
            • 7. Remove the chocks from the four caster wheels on the bottom of the jukebox.
            • WARNING Push the jukebox only from the right or left sides (see Figure 1-1). Pushing the jukebox ...
              • WARNING Push the jukebox only from the right or left sides (see Figure 1-1). Pushing the jukebox ...
          • 8. Repackage the jukebox in the same way it was received
            • 8. Repackage the jukebox in the same way it was received
            • NOTE Your service representative can provide assistance or advise you on how to best repackage an...
              • NOTE Your service representative can provide assistance or advise you on how to best repackage an...
      2 Using Optical Disks

      • 2 Using Optical Disks
      • Overview of This Chapter
        • Overview of This Chapter
        • Using Optical Disks
          • Using Optical Disks
          • The optical disks that you use with your jukebox are an integral part of the storage process. Thi...
          • • choosing an optical disk type
            • • choosing an optical disk type
              • • choosing an optical disk type
            • • labeling optical disks
              • • labeling optical disks
            • • write-protecting optical disks
              • • write-protecting optical disks
            • • caring for optical disks
              • • caring for optical disks
          • IMPORTANT Hewlett-Packard conducts extensive product quality testing to ensure it’s magneto-optic...
            • IMPORTANT Hewlett-Packard conducts extensive product quality testing to ensure it’s magneto-optic...
            • That’s why HP recommends using HP-brand optical media with its jukeboxes.
            • For additional details and specifications for HP optical media, or to purchase media online, go t...
      • disks:choosing
        • disks:choosing
          • disks:choosing
        • Two disk types are available for use in the jukebox: rewritable disks and write-once disks.
        • To choose which type of disks to use, consider these points:
        • • Rewritable optical disks--data can be repeatedly written and erased.
          • • Rewritable optical disks--data can be repeatedly written and erased.
            • • Rewritable optical disks--data can be repeatedly written and erased.
          • • Write-Once optical disks--data can be written only once, and the data cannot be altered or eras...
            • • Write-Once optical disks--data can be written only once, and the data cannot be altered or eras...
          • • Rewritable and write-once disks come in sector sizes from 4,096 bytes/sector down to 512 bytes/...
            • • Rewritable and write-once disks come in sector sizes from 4,096 bytes/sector down to 512 bytes/...
        • NOTE Do not use write-once disks in a computer system that does not support write-once disks. Che...
          • NOTE Do not use write-once disks in a computer system that does not support write-once disks. Che...
      • disks:labeling
        • disks:labeling
          • disks:labeling
        • Make it a practice to label your optical disk cartridges. You are provided adhesive labels with e...
        • NOTE Your jukebox application software may label your optical disk slot locations differently. Us...
          • NOTE Your jukebox application software may label your optical disk slot locations differently. Us...
        • • storage slot location (1, 2, 3, ... )
          • • storage slot location (1, 2, 3, ... )
            • • storage slot location (1, 2, 3, ... )
          • • date of format or initialization
            • • date of format or initialization
          • • disk owner (group, department, etc.)
            • • disk owner (group, department, etc.)
          • • storage purpose (backup, old version of operating system, etc.)
            • • storage purpose (backup, old version of operating system, etc.)
        • HP recommends using end labels as shown in Figure 2-1. End labels reduce the chance of label mate...
        • disk:labels jamming shutter
          • disk:labels jamming shutter
            • disk:labels jamming shutter
        • Figure 2-1 Recommended Placement of Cartridge Labels
          • Figure 2-1 Recommended Placement of Cartridge Labels
      • disks:writeprotecting
        • disks:writeprotecting
          • disks:writeprotecting
        • Each side of an optical disk can be write-protected by sliding the write-protect button in the di...
        • With rewritable optical disks, write-protecting the disk prevents overwriting existing files and ...
        • With write-once optical disks, existing files cannot be altered or erased regardless of whether o...
        • Figure 2-2 Write-Protect Button Location
          • Figure 2-2 Write-Protect Button Location
      • disks:care of
        • disks:care of
          • disks:care of
        • Follow these guidelines to ensure that your optical disks remain in good condition:
        • • Do not expose disks to extreme magnetic fields.
          • • Do not expose disks to extreme magnetic fields.
            • • Do not expose disks to extreme magnetic fields.
          • • Do not expose disks to dust particles.
            • • Do not expose disks to dust particles.
          • • Do not expose disks to extreme temperatures or extreme humidity.
            • • Do not expose disks to extreme temperatures or extreme humidity.
          • • Do not drop the disks.
            • • Do not drop the disks.
          • • Do not open a disk's metal shutter and touch the disk surface.
            • • Do not open a disk's metal shutter and touch the disk surface.
          • • Do not take disks apart.
            • • Do not take disks apart.
          • • Do not insert disks with loosely-attached labels into the jukebox.
            • • Do not insert disks with loosely-attached labels into the jukebox.
          • • Remove old disk labels before applying new ones especially if you choose to place labels on the...
            • • Remove old disk labels before applying new ones especially if you choose to place labels on the...
          • • Store disks in a clean, safe place when they are not in use.
            • • Store disks in a clean, safe place when they are not in use.
        • disks:cleaning
          • disks:cleaning
            • disks:cleaning
          • Normally, an optical disk does not require cleaning when used in a computer room or clean office ...
          • CAUTION Be very careful when cleaning an optical disk. Abrasive particles dragged across the disk...
            • CAUTION Be very careful when cleaning an optical disk. Abrasive particles dragged across the disk...
            • Clean a disk only with a disk cleaning kit. Follow the disk cleaning kit instructions exactly.
          • HP-approved disk cleaning kits are listed at
      3 Operating the Jukebox

      • 3 Operating the Jukebox
      • Overview of This Chapter
        • Overview of This Chapter
        • This chapter gives information on the following topics:
        • • operating the control panel
          • • operating the control panel
            • • operating the control panel
          • • using the selection buttons
            • • using the selection buttons
          • • interpreting messages which appear in the display window
            • • interpreting messages which appear in the display window
          • • loading optical disks into the jukebox
            • • loading optical disks into the jukebox
          • • ejecting optical disks from the jukebox
            • • ejecting optical disks from the jukebox
          • • entering the administration menu password
            • • entering the administration menu password
          • • changing the administration menu password
            • • changing the administration menu password
          • • setting SCSI IDs or logical unit numbers (LUNs)
            • • setting SCSI IDs or logical unit numbers (LUNs)
          • • setting configurations
            • • setting configurations
          • • retrieving performance information
            • • retrieving performance information
          • • running tests (for service use)
            • • running tests (for service use)
          • • using online repair (for service use only)
            • • using online repair (for service use only)
          • • troubleshooting
            • • troubleshooting
      • Operating the Control Panel
        • Operating the Control Panel
        • The control panel enables manual control of all jukebox operations using six buttons and an LED d...
        • The SCSI IDs of the jukebox and its optical drives can be set and changed, disks may be loaded an...
        • The figure and text on the next two pages show the user controls and mailslot. The rest of the ch...
        • Figure 3-1 The Jukebox Control Panel
          • Figure 3-1 The Jukebox Control Panel
        • The numbers below refer to the numbers in Figure 3-1 on the previous page.
      • 1
      • 16-Character Display
        • controls:16-character display
        • 16-character display
        • display
      • Displays status information and control panel information
      • 2
      • Selection buttons
        • controls:selection buttons
        • selection buttons
      • Pressed to perform the following operations:
        • Pressed to perform the following operations:
        • LOAD
          • LOAD
        • EJECT
          • EJECT
        • PREV
          • PREV
        • NEXT
          • NEXT
        • CANCEL
          • CANCEL
        • ENTER
          • ENTER
      • 3
      • Activity light
        • controls:activity light
        • activity light
      • Lit differently to indicate the following:
        • Lit differently to indicate the following:
        • • Steady Green - power is on
          • • Steady Green - power is on
            • • Steady Green - power is on
          • • Flashing Green - an optical drive is being accessed
            • • Flashing Green - an optical drive is being accessed
          • • Amber - a fault occurred
            • • Amber - a fault occurred
      • 4
      • Mailslot
        • mailslot
      • Used to load and eject optical disks
      NOTE Figure 3-2 shows the jukebox menus available using the control panel selection buttons.

      • NOTE Figure 3-2 shows the jukebox menus available using the control panel selection buttons.
      Figure 3-2 Jukebox Display Menu Tree

      • Figure 3-2 Jukebox Display Menu Tree
      using the selection buttons

      • using the selection buttons
        • using the selection buttons
        • controls:EJECT button
        • controls:NEXT button
        • controls:PREV button
        • controls:CANCEL button
        • controls:ENTER button
      • controls:LOAD button
        • controls:LOAD button
      • Each time you push the
      • NOTE You can get back to
        • NOTE You can get back to
      display messages

      • display messages
        • display messages
      • The display window shows the operations you may select. Instructions for selecting or changing ch...
      • top level displays:ADMIN *
        • top level displays:ADMIN *
          • top level displays:ADMIN *
        • READY
          • READY
            • READY
              • READY
            • The jukebox is ready for operation.
              • The jukebox is ready for operation.
          • ADMIN
            • ADMIN
              • ADMIN
            • Select to access second-level choices. You must enter a security code to access these choices.
              • Select to access second-level choices. You must enter a security code to access these choices.
        • NOTE A
          • NOTE A
      • second level displays:TEST *
        • second level displays:TEST *
          • second level displays:TEST *
          • second level displays:INFO *
          • second level displays:CONFIG *
          • second level displays:ONLINE REPAIR *
          • second level displays:SCSI IDs *
        • You must enter a security code before accessing these functions. See “Entering the Administration...
        • TEST
          • TEST
            • TEST
              • TEST
            • Select to run internal tests (normally, these are run by service).
              • Select to run internal tests (normally, these are run by service).
          • INFO
            • INFO
              • INFO
            • Select to retrieve performance information stored in the jukebox logs.
              • Select to retrieve performance information stored in the jukebox logs.
          • CONFIG
            • CONFIG
              • CONFIG
            • Select to customize the way the jukebox functions.
              • Select to customize the way the jukebox functions.
          • SCSI IDs
            • SCSI IDs
              • SCSI IDs
            • Select to view and/or change the SCSI IDs and logical unit numbers (LUNs).
              • Select to view and/or change the SCSI IDs and logical unit numbers (LUNs).
          • ONLINE REPAIR
            • ONLINE REPAIR
              • ONLINE REPAIR
            • Select to view and change drive settings for online drive replacement (used by service
              • Select to view and change drive settings for online drive replacement (used by service
        • NOTE An “
          • NOTE An “
          • In Figure 3-2, you can display the selections listed in boxes below the
      disks:loading

      • disks:loading
        • disks:loading
        • loading disks
      • NOTE Label all disks before loading them into the jukebox. (See “Labeling an Optical Disk Cartrid...
        • NOTE Label all disks before loading them into the jukebox. (See “Labeling an Optical Disk Cartrid...
      • Start with
        • Start with
      • 1. Press
        • 1. Press
          • 1. Press
            • 1. Press
            • Figure 3-3 Loading a Disk
              • Figure 3-3 Loading a Disk
          • 2. When the mailslot opens, insert a disk into the mailslot with Side A of the disk facing up. Th...
            • 2. When the mailslot opens, insert a disk into the mailslot with Side A of the disk facing up. Th...
            • When the disk is inserted, it is automatically pulled into the mailslot. An incorrectly inserted ...
          • 3. If you want to select the storage slot number that shows in the display, press
            • 3. If you want to select the storage slot number that shows in the display, press
          • 4. LOADING
            • 4. LOADING
              • 4. LOADING
          • 5. Press
            • 5. Press
      • NOTE Some software packages require that you load and eject disks by following the instructions i...
        • NOTE Some software packages require that you load and eject disks by following the instructions i...
      • Start with
        • Start with
      • 1. Press
        • 1. Press
          • 1. Press
        • 2. EJECT SLOT #
          • 2. EJECT SLOT #
            • 2. EJECT SLOT #
        • 3. If you want to select the storage slot number that shows in the display, press
          • 3. If you want to select the storage slot number that shows in the display, press
          • EJECTING
            • EJECTING
        • 4. Remove the disk from the mailslot.
          • 4. Remove the disk from the mailslot.
          • You may now eject additional disks by pressing the
        • 5. Press
          • 5. Press
      administration menu password:entering

      • administration menu password:entering
        • administration menu password:entering
      • READY
        • READY
      • A numeric password is required to access menu choices beneath the
      • NOTE Don't forget your password. If you forget it, only your service representative can reset the...
        • NOTE Don't forget your password. If you forget it, only your service representative can reset the...
      • Follow these steps to enter the password. If you want to change the password, go to the next sect...
      • Start with
        • Start with
      • 1. Press
        • 1. Press
          • 1. Press
        • 2. Press
          • 2. Press
          • NOTE If the default password,
            • NOTE If the default password,
            • If you have set your own password into the jukebox, continue with Steps 3 to 5 below.
        • 3. Press
          • 3. Press
        • 4. Press
          • 4. Press
        • 5. Press
          • 5. Press
      • To access menu choices under the
      administration menu password:changing

      • administration menu password:changing
        • administration menu password:changing
      • READY
        • READY
      • 1. Follow the steps on the previous page to enter your password (or the default, factory-set pass...
        • 1. Follow the steps on the previous page to enter your password (or the default, factory-set pass...
          • 1. Follow the steps on the previous page to enter your password (or the default, factory-set pass...
        • 2.
          • 2.
        • 3. Press
          • 3. Press
        • 4.
          • 4.
        • 5. Press
          • 5. Press
        • 6. Press
          • 6. Press
        • 7. PASSWORD CHANGED
          • 7. PASSWORD CHANGED
            • 7. PASSWORD CHANGED
          • CAUTION Turning off the jukebox in the next step could cause data loss if not done correctly.
            • CAUTION Turning off the jukebox in the next step could cause data loss if not done correctly.
            • Do not turn off power to the jukebox until you are sure the SCSI bus is inactive. Removing power ...
        • 8. Turn the jukebox OFF, then ON to save the password to the jukebox flash ROM.
          • 8. Turn the jukebox OFF, then ON to save the password to the jukebox flash ROM.
      setting the SCSI IDs

      • setting the SCSI IDs
        • setting the SCSI IDs
        • SCSI IDs:setting
      • NOTE If you are unfamiliar with basic SCSI addressing or LUN addressing, refer to Appendix B.
        • NOTE If you are unfamiliar with basic SCSI addressing or LUN addressing, refer to Appendix B.
      • First, determine if you are using basic SCSI addressing or logical unit numbering (LUN). Setting ...
      • Next, either view the current SCSI IDs or proceed directly to setting IDs. The next two procedure...
      • Tables showing default SCSI IDs for basic SCSI addressing and LUN addressing are in Appendix B.
      • setting the LUN mode
        • setting the LUN mode
          • setting the LUN mode
          • LUN mode:setting
        • READY
          • READY
        • NOTE If you are unfamiliar with basic SCSI addressing or LUN addressing, refer to Appendix B.
          • NOTE If you are unfamiliar with basic SCSI addressing or LUN addressing, refer to Appendix B.
        • NOTE Check your host system documentation and jukebox application software documentation to verif...
          • NOTE Check your host system documentation and jukebox application software documentation to verif...
        • Start with
          • Start with
        • 1. Press
          • 1. Press
            • 1. Press
          • 2. Enter the administration password.
            • 2. Enter the administration password.
            • Instructions for entering this password are in “Entering the Administration Menu Password” previo...
          • 3. Press
            • 3. Press
          • 4.
            • 4.
          • 5. Press
            • 5. Press
            • You may now view the SCSI ID and LUN numbers using
      • SCSI IDs:viewing
        • SCSI IDs:viewing
          • SCSI IDs:viewing
          • viewing the current SCSI IDs
        • READY
          • READY
        • NOTE If you are unfamiliar with basic SCSI addressing or LUN addressing, refer to Appendix B.
          • NOTE If you are unfamiliar with basic SCSI addressing or LUN addressing, refer to Appendix B.
        • Start with
          • Start with
        • 1. Press
          • 1. Press
            • 1. Press
          • 2. Enter the administration password.
            • 2. Enter the administration password.
            • Instructions for entering this password are in “Entering the Administration Menu Password” previo...
          • 3. Press
            • 3. Press
          • 4. VIEW ID’S
            • 4. VIEW ID’S
              • 4. VIEW ID’S
          • 5.
            • 5.
            • If you want to view the IDs on Bus 2, press
          • 6. JKBX ID # LUN #
            • 6. JKBX ID # LUN #
              • 6. JKBX ID # LUN #
            • Press
            • NOTE Tables in Appendix B show the default SCSI IDs and LUNs when LUN mode is turned on.
              • NOTE Tables in Appendix B show the default SCSI IDs and LUNs when LUN mode is turned on.
          • 7. Press
            • 7. Press
      • changing the SCSI IDs
        • changing the SCSI IDs
          • changing the SCSI IDs
          • SCSI IDs:changing
        • READY
          • READY
        • NOTE If you are unfamiliar with basic SCSI addressing or LUN addressing, refer to Appendix B.
          • NOTE If you are unfamiliar with basic SCSI addressing or LUN addressing, refer to Appendix B.
        • Start with
          • Start with
        • 1. Press
          • 1. Press
            • 1. Press
          • 2. Enter the administration password.
            • 2. Enter the administration password.
            • Instructions for entering this password are in “Entering the Administration Menu Password” previo...
          • 3. Press
            • 3. Press
          • 4. VIEW ID’S
            • 4. VIEW ID’S
              • 4. VIEW ID’S
            • BUS 1 *
              • BUS 1 *
            • If you want to change the IDs on Bus 2, press
            • If you are using basic SCSI addressing (LUN mode OFF)
              • If you are using basic SCSI addressing (LUN mode OFF)
            • JKBX ID # LUN #
              • JKBX ID # LUN #
            • If you are using LUN addressing (LUN mode ON)
              • If you are using LUN addressing (LUN mode ON)
            • JKBX BUS 1 #
              • JKBX BUS 1 #
          • 5. Press
            • 5. Press
            • NOTE In the next step you will choose a new ID. Review this note.
              • NOTE In the next step you will choose a new ID. Review this note.
              • This jukebox, by default, assigns ID 6 to the jukebox controller. When in LUN mode, the jukebox c...
              • Some host computer systems do not allow you to assign different device types to the same ID. If y...
              • Tables in Appendix B show jukebox default settings and an example of setting the jukebox controll...
              • If another device ID is placed between the jukebox controller and the drives, problems can result...
          • 6. Press
            • 6. Press
            • If the jukebox is set to
          • 7. (If using basic SCSI addressing - LUN mode OFF) Press
            • 7. (If using basic SCSI addressing - LUN mode OFF) Press
          • 8. UPDATE
            • 8. UPDATE
              • 8. UPDATE
            • • If the new settings do not conflict with other SCSI IDs on the bus,
              • • If the new settings do not conflict with other SCSI IDs on the bus,
                • • If the new settings do not conflict with other SCSI IDs on the bus,
              • • If the new settings conflict with other IDs on the SCSI bus,
                • • If the new settings conflict with other IDs on the SCSI bus,
            • NOTE When in LUN mode: If the new ID you choose results in the IDs for the jukebox controller and...
              • NOTE When in LUN mode: If the new ID you choose results in the IDs for the jukebox controller and...
          • 9. Press
            • 9. Press
            • CAUTION Turning off the jukebox in the next step could cause data loss if not done correctly.
              • CAUTION Turning off the jukebox in the next step could cause data loss if not done correctly.
              • Do not turn off power to the jukebox until you are sure the SCSI bus is inactive. Removing power ...
          • 10. Turn the jukebox OFF, then ON to save the IDs to the jukebox flash ROM.
            • 10. Turn the jukebox OFF, then ON to save the IDs to the jukebox flash ROM.
      configuration:setting

      • configuration:setting
        • configuration:setting
      • READY
        • READY
      • You can set configurations to customize the way the jukebox operates.
      • Start with
        • Start with
      • 1. Press
        • 1. Press
          • 1. Press
        • 2. Enter the administration password.
          • 2. Enter the administration password.
          • Instructions for entering this password are in “Entering the Administration Menu Password” previo...
        • 3. TEST *
          • 3. TEST *
            • 3. TEST *
        • 4. Press
          • 4. Press
          • If the configuration has multiple settings, the current setting flashes. Otherwise, the configura...
        • 5. If the current configuration setting is flashing, press
          • 5. If the current configuration setting is flashing, press
        • 6. Press
          • 6. Press
          • CAUTION Turning off the jukebox in the next step could cause data loss if not done correctly.
            • CAUTION Turning off the jukebox in the next step could cause data loss if not done correctly.
            • Do not turn off power to the jukebox until you are sure the SCSI bus is inactive. Removing power ...
        • 7. Turn the jukebox OFF, then ON to save the configuration to the jukebox flash ROM.
          • 7. Turn the jukebox OFF, then ON to save the configuration to the jukebox flash ROM.
          • Configurations are described in the following table.
      • configurations:listing of
        • configurations:listing of
          • configurations:listing of
      • Configuration Name
      • Description
      • RECOVERY ON/OFF
        • RECOVERY ON/OFF
      • Toggles between ON and OFF. If the configuration is set to ON, the jukebox attempts to recover fr...
      • RESTORE DEFAULTS
        • RESTORE DEFAULTS
      • Sets all jukebox configurations to default settings.
      • CLEAR ODOMETERS
        • CLEAR ODOMETERS
      • Used by service personnel only. Sets all jukebox odometers to zero.
        • Used by service personnel only.
      • DUAL PICKER ON/OFF
        • DUAL PICKER ON/OFF
      • Toggles between ON and OFF. (The default setting is DUAL PICKER ON, and dual picker mode should r...
      • STARWARS ON/OFF
        • STARWARS ON/OFF
      • Used by service personnel only. Should be set to ON during normal operation. Toggles between ON a...
        • Used by service personnel only.
      • NEW PASSWORD
        • NEW PASSWORD
      • Allows you to change the numerical password required to access the menu choices under the ADMIN *...
      • SCSI LOG ON/OFF
        • SCSI LOG ON/OFF
      • Used by service personnel only. Should be set to OFF during normal operation. Toggles between ON ...
        • Used by service personnel only.
      • SECURE MS ON/OFF
        • SECURE MS ON/OFF
      • Toggles between ON and OFF. The ON configuration disables loading and ejecting disks. The OFF con...
      • SLTS 230-238 ON/OFF
        • SLTS 230-238 ON/OFF
      • Slots 230 to 238 may not be supported by some jukebox application software. The ON configuration ...
      • POWER SECURE ON/OFF
        • POWER SECURE ON/OFF
      • Toggles between ON and OFF. The ON configuration retains your selection of the SECURE MS configur...
      • REP RECOVERED ON/OFF
        • REP RECOVERED ON/OFF
      • Toggles between ON and OFF. When set to ON, recovered errors are reported; when set to OFF, recov...
      • CONF40 ON/OFF
        • CONF40 ON/OFF
      • Used by service personnel only. Changing this configuration may result in a service call.
        • Used by service personnel only. Changing this configuration may result in a service call.
      • WRITE VERIFY ON/OFF
        • WRITE VERIFY ON/OFF
      • Toggles between ON and OFF. When set to ON (default), write verify is forced. When set to OFF, th...
      • MS DOOR OPEN/CLOSED
        • MS DOOR OPEN/CLOSED
      • Toggles between OPEN and CLOSED. When set to OPEN, the mailslot door always remains open; when se...
      retrieving log history

      • retrieving log history
        • retrieving log history
        • logs:retrieving
      • READY
        • READY
      • You can display information stored in the jukebox operating logs by using the
      • Start with
        • Start with
      • 1. Press
        • 1. Press
          • 1. Press
        • 2. Enter the administration password.
          • 2. Enter the administration password.
          • Instructions for entering this password are in “Entering the Administration Menu Password” in thi...
        • 3. TEST *
          • 3. TEST *
            • 3. TEST *
        • 4. Press
          • 4. Press
        • 5. After you are finished viewing log information, press
          • 5. After you are finished viewing log information, press
          • Information logs are described in the following table.
      • logs:listing of
        • logs:listing of
          • logs:listing of
      • Log Name
      • Description
      • REVISION
        • REVISION
          • REVISION
      • Jukebox firmware version number.
      • JUKEBOX *
        • JUKEBOX *
      • Press ENTER to select the information described in the next five rows.
      • product #
      • Product identification string
      • SN #
      • Serial number of the unit.
      • FW TYPE ##
      • Code that identifies the type of firmware used in the unit.
      • DRIVES #
      • Number of drives in the unit.
      • SLOTS #
      • Number of available storage slots in the unit.
      • JKBX ODOMETERS *
        • JKBX ODOMETERS *
      • Press ENTER to select the odometer logs described in the next five rows.
      • HOURS
      • Number of operation hours (time the power was on). Some of the time may be while in power reducti...
      • MOVES
      • Total moves and move attempts by the disk transport mechanism.
      • FLIPS
      • Total disk transport mechanism flips.
      • XLATES
      • Total disk transport mechanism horizontal moves.
      • ROTATES
      • Total mailslot rotations.
      • DRIVE LOADS *
        • DRIVE LOADS *
      • Press ENTER to select the logs under this selection.
      • DRIVE #
      • Total disk loads for the drive numbered “#.”
      • DRIVE FW *
        • DRIVE FW *
      • Press ENTER to select the logs under this selection.
      • D# REV x.xx
      • Drive firmware revision code. “D#” is the drive number and x.xx is the code. Press NEXT or PREV t...
      • DRIVE SN *
        • DRIVE SN *
      • Press ENTER to select the logs under this selection.
      • D# xxxxxxx
      • Serial number of the drive where “#” is the drive number. Press NEXT or PREV to select drive numb...
      • HARD ERROR *
        • HARD ERROR *
      • Log of unrecoverable errors (commands that did not successfully complete). Returns either NO HARD...
        • Log of unrecoverable errors (commands that did not successfully complete). Returns either
        • Press
        • (Log entries are described in the rows following
      • SOFT ERROR *
        • SOFT ERROR *
      • Log of recovered errors (commands that complete successfully). Returns either NO SOFT ENTRIES or ...
        • Log of recovered errors (commands that complete successfully). Returns either
        • Press
      • RECOVERY ERROR *
        • RECOVERY ERROR *
      • Log of errors during the most recent move. Returns either NO ENTRIES or the number of recovery er...
        • Log of errors during the most recent move. Returns either
        • Press
      • *HARDWARE ERR #
      • Internal diagnostics error number of the cause of the failure.
      • *FRU 1 #
      • Field replaceable unit most likely to be at fault.
      • *FRU 2 #
      • Field replaceable unit second most likely to be at fault.
      • *FRU 3 #
      • Field replaceable unit third most likely to be at fault.
      • MOTION
      • indicates one of the following types of movements taking place in the jukebox at the time ...
        • indicates one of the following types of movements taking place in the jukebox at the time ...
        • • EXCHANGE
          • • EXCHANGE
            • • EXCHANGE
          • • MOVE
            • • MOVE
          • • POSITION
            • • POSITION
          • • INIT ELEM
            • • INIT ELEM
          • • REZERO
            • • REZERO
          • • ROTATE
            • • ROTATE
          • • DIAGNOSTIC
            • • DIAGNOSTIC
          • • RESTORE
            • • RESTORE
      • SOURCE #
      • Element number to which the source refers. (This information is valid for MOVE, EXCHANGE, and POS...
      • DESTINATION 1 #
      • Element to which the first destination refers. (This information is valid for MOVE and EXCHANGE m...
      • DESTINATION 2 #
      • Element to which the second destination refers. (This information is valid for the EXCHANGE movem...
      • ODOMETER #
      • Move number in which the error occurred.
      • *MICROMOVE 1 #
      • First jukebox micro-move for the original move command issued prior to the failure.
      • *MICROMOVE 2 #
      • Second jukebox micro-move for the original move command issued prior to the failure.
      • *MICROMOVE 3 #
      • Third jukebox micro-move for the original move command issued prior to the failure.
      • *MICROMOVE 4 #
      • Fourth jukebox micro-move for the original move command issued prior to the failure.
      • *MICROMOVE 5 #
      • Fifth jukebox micro-move for the original move command issued prior to the failure.
      • *MICROMOVE 6 #
      • Sixth jukebox micro-move for the original move command issued prior to the failure. (This is the ...
      • *MICROMOVE ER #
      • Micro-move error that occurred.
      • TOP or BOTTOM PICKER
      • Displays either TOP or BOTTOM indicating which side of the disk transport mechanism was active at...
      • NORTH or SOUTH THUMB
      • Displays either NORTH or SOUTH indicating which thumb on the transport mechanism was active at th...
      * Press
      running an internal test

      • running an internal test
        • running an internal test
        • internal tests:running
      • READY
        • READY
      • The optical jukebox can run self-diagnostic tests.
      • CAUTION Some of the internal diagnostic tests of this jukebox can corrupt your file system if not...
        • CAUTION Some of the internal diagnostic tests of this jukebox can corrupt your file system if not...
        • In almost all cases, these tests should be run only by authorized service personnel. Service, how...
        • Instructions for running internal tests are included in this guide to help you run tests if reque...
      • Start with
        • Start with
      • 1. Press
        • 1. Press
          • 1. Press
        • 2. Enter the administration password.
          • 2. Enter the administration password.
          • Instructions for entering this password are in “Entering the Administration Menu Password” previo...
        • 3. TEST *
          • 3. TEST *
            • 3. TEST *
        • 4. Press
          • 4. Press
          • NOTE You may press
            • NOTE You may press
      • internal tests:listing of
        • internal tests:listing of
          • internal tests:listing of
      • Test Name
      • Description
      • Internal Tests are normally for service use only. Some of the following ...
        • Internal Tests are normally for service use only. Some of the following ...
        • If you are in contact with your service representative, you may be requested to run one or more o...
      • EXCHANGE DEMO
      • Used by service personnel only. Do not run this test if the jukebox contains disks with file syst...
        • Used by service personnel only. Do not run this test if the jukebox contains disks with file syst...
      • INIT MECHANICS
      • Runs the FIND PLUNGE HOME, FIND VERTICAL HOME, FIND XLATE HOME, and INIT ELEM STATUS tests. Each ...
      • INIT ELEM STATUS
      • Physically scans the entire unit to determine which storage slots contain disks and if the drives...
      • MAGAZINE IO
      • Makes a combination of moves with a PASS/FAIL result. It moves an optical disk from a randomly-ch...
      • DRIVE IO
      • Makes a combination of moves with a PASS/FAIL result. It moves an optical disk from a randomly- c...
      • MAILSLOT IO
      • Makes a combination of moves with a PASS/FAIL result. It moves an optical disk from the lowest- n...
      • VERTICAL TEST
      • Moves the disk transport mechanism up and down the full length of the rail. Returns PASS/FAIL. No...
      • TRANSLATE TEST
      • Moves the disk transport mechanism from side to side. No disks are required.
      • FLIP TEST
      • Makes a combination of moves with a PASS/FAIL result. Flips the disk transport mechanism at vario...
      • PICKER TEST
      • Flips the disk transport mechanism and switches active thumbs. No disks are required.
      • FIND PLUNGE HOME
      • Calibrates the disk transport mechanism, establishes the mechanism’s orientation, and determines ...
      • FIND VERT HOME
      • Recalibrates the vertical position of the disk transport mechanism and verifies that the vertical...
      • FIND XLATE HOME
      • Calibrates the reference points for the side-to-side motion of the disk transport mechanism. No d...
      • VERTICAL ENCODER
      • Moves the disk transport mechanism down to the lower stop, moves it back up a short distance, and...
      • EMPTY DRIVES
      • Used by service personnel only. Do not run this test if the jukebox contains disks with file syst...
        • Used by service personnel only. Do not run this test if the jukebox contains disks with file syst...
      • EMPTY PICKER
      • Used by service personnel only. Do not run this test if the jukebox contains disks with file syst...
        • Used by service personnel only. Do not run this test if the jukebox contains disks with file syst...
      • FILL PICKER
      • Used by service personnel only. Do not run this test if the jukebox contains disks with file syst...
        • Used by service personnel only. Do not run this test if the jukebox contains disks with file syst...
      • EXERCISE MECH
      • Runs the VERTICAL TEST, TRANSLATE TEST, FLIP TEST, MAGAZINE IO, DRIVE IO, and MAILSLOT IO tests. ...
      • WELLNESS TEST
      • Checks the general capability of the jukebox. Requires one loaded disk. The drives, transport, an...
      • CLEAR SOFT LOG
      • Sets the soft error log to zero.
      • CLEAR HARD LOG
      • Sets the hard error log to zero.
      • PLUNGE FULL SPD
      • Allows the disk transport mechanics to run at full speed. This setting should always be used in n...
      • PLUNGE 1/2 SPD
      • Used by service personnel only. Allows the disk transport mechanics to run at half speed.
        • Used by service personnel only.
      • PLUNGE 1/4 SPD
      • Used by service personnel only. Allows the disk transport mechanics to run at quarter speed.
        • Used by service personnel only.
      • STARWARS
      • The display shows 0 0 0.
      • BOTTOM THUMB
      • Used by service personnel only. Reports THUMB A, THUMB B, or NO THUMB. Looks at the top and botto...
        • Used by service personnel only.
      • TOP THUMB
      • Used by service personnel only.Reports ON or OFF. Looks at the top thumb sensor which reports whe...
        • Used by service personnel only.
      • TRANSLATE SENSOR
      • Reports ON or OFF after looking at the translate calibration sensor. (Display automatically updat...
      online repair:service use

      • online repair:service use
        • online repair:service use
      • The online repair selection allows an authorized service representative to replace a faulty drive...
      • CAUTION Selecting online repair should be done only by an authorized service representative. This...
        • CAUTION Selecting online repair should be done only by an authorized service representative. This...
      troubleshooting

      • troubleshooting
        • troubleshooting
      • This section provides steps you can take when problems occur during operation.
      • If the troubleshooting procedures do not resolve the problem, call your service provider. If you ...
      • NOTE If a service call is necessary, gather the following information before calling your service...
        • NOTE If a service call is necessary, gather the following information before calling your service...
        • • model of your jukebox
          • • model of your jukebox
            • • model of your jukebox
          • • serial number
            • • serial number
          • • brand and model of your host computer
            • • brand and model of your host computer
          • • brand and model of your host computer SCSI adapter
            • • brand and model of your host computer SCSI adapter
          • • jukebox application software you are using and its version
            • • jukebox application software you are using and its version
          • • any jukebox driver separate from your jukebox application software and the version of this driver.
            • • any jukebox driver separate from your jukebox application software and the version of this driver.
      • troubleshooting:listing of procedures
        • troubleshooting:listing of procedures
          • troubleshooting:listing of procedures
      • Problem
      • What to do
      • Jukebox won't power on.
      • • Ensure that power cord connections are tight.
        • • Ensure that power cord connections are tight.
          • • Ensure that power cord connections are tight.
            • • Ensure that power cord connections are tight.
          • • Ensure that the power switch is ON (located on the lower right side of the jukebox rear panel).
            • • Ensure that the power switch is ON (located on the lower right side of the jukebox rear panel).
          • • Ensure that the power outlet is operating.
            • • Ensure that the power outlet is operating.
          • • Replace the power cord with a known good one.
            • • Replace the power cord with a known good one.
          • • If steps above are unsuccessful, call your service representative.
            • • If steps above are unsuccessful, call your service representative.
      • Poweron selftest failed and DEVICE FAILED displays
      • • Power cycle the jukebox.*
        • • Power cycle the jukebox.*
          • • Power cycle the jukebox.*
            • • Power cycle the jukebox.*
          • • If the poweron test continues to fail, press
            • • If the poweron test continues to fail, press
      • DEVICE FAILED displays.
        • DEVICE FAILED
          • DEVICE FAILED
        • Hardware Error #61 (External SCSI cables) is reported.
      • • Ensure that only one SCSI device type (single-ended OR differential) exists on the SCSI bus.
        • • Ensure that only one SCSI device type (single-ended OR differential) exists on the SCSI bus.
          • • Ensure that only one SCSI device type (single-ended OR differential) exists on the SCSI bus.
            • • Ensure that only one SCSI device type (single-ended OR differential) exists on the SCSI bus.
          • • Verify that the SCSI interface selection switch is set correctly (either single-ended or differ...
            • • Verify that the SCSI interface selection switch is set correctly (either single-ended or differ...
          • • Verify that the terminator is the correct type (single-ended or differential).
            • • Verify that the terminator is the correct type (single-ended or differential).
          • • If steps above are unsuccessful, call your service representative.
            • • If steps above are unsuccessful, call your service representative.
      • Power to the jukebox failed while a disk was in the drive and the display did not return to READY...
      • • Power cycle the jukebox.*
        • • Power cycle the jukebox.*
          • • Power cycle the jukebox.*
            • • Power cycle the jukebox.*
          • • If
            • • If
      • *Ensure that the SCSI bus is inactive before removing power to the jukebox. Removing power to a d...
        • *Ensure that the SCSI bus is inactive before removing power to the jukebox. Removing power to a d...
      • No display messages.
      • • Ensure that the power cord is connected.
        • • Ensure that the power cord is connected.
          • • Ensure that the power cord is connected.
            • • Ensure that the power cord is connected.
          • • Ensure that the power switch is ON.
            • • Ensure that the power switch is ON.
          • • Power cycle the jukebox.*
            • • Power cycle the jukebox.*
          • • If steps above are unsuccessful, call your service representative.
            • • If steps above are unsuccessful, call your service representative.
      • Changed the drive ID but the new ID isn't recognized.
      • Some computers require a restart to recognize new SCSI IDs.
        • Some computers require a restart to recognize new SCSI IDs.
        • • Ensure the SCSI bus is inactive and restart your host computer.
          • • Ensure the SCSI bus is inactive and restart your host computer.
            • • Ensure the SCSI bus is inactive and restart your host computer.
      • Forgot your password.
      • • Enter the default password (000 000 000).
        • • Enter the default password (
          • • Enter the default password (
            • • Enter the default password (
          • • If the default password is not accepted, call your service representative.
            • • If the default password is not accepted, call your service representative.
      • Disk inserted in the mailslot but LOAD ERROR or FAILED displays.
      • • Press CANCEL. Insert the disk in the mailslot again. See “Loading an Optical Disk into the Juke...
        • • Press
          • • Press
            • • Press
          • • If the light bar on the front panel is orange, cycle power to the jukebox.* Try to load the dis...
            • • If the light bar on the front panel is orange, cycle power to the jukebox.* Try to load the dis...
          • • If the disk is in the mailslot correctly and these error messages repeat, call your service rep...
            • • If the disk is in the mailslot correctly and these error messages repeat, call your service rep...
      • Disk inserted in the mailslot but RESERVED displays
      • The SECURE MS configuration is set. Disks cannot be loaded.
        • The
        • • If appropriate, change this setting. See “Setting an Operating Configuration” in this chapter. ...
          • • If appropriate, change this setting. See “Setting an Operating Configuration” in this chapter. ...
            • • If appropriate, change this setting. See “Setting an Operating Configuration” in this chapter. ...
      • *Ensure that the SCSI bus is inactive before removing power to the jukebox. Removing power to a d...
      • Disk inserted in the mailslot but MAILSLOT EMPTY displays
      • The mailslot sensors do not detect a disk in the mailslot.
        • The mailslot sensors do not detect a disk in the mailslot.
        • • Remove and then replace the disk fully into the mailslot. If the same error reappears, the mail...
          • • Remove and then replace the disk fully into the mailslot. If the same error reappears, the mail...
            • • Remove and then replace the disk fully into the mailslot. If the same error reappears, the mail...
      • Disk inserted in the mailslot but DEST NOW FULL displays
      • The jukebox moved a disk into the slot you chose before your load command executed.
        • The jukebox moved a disk into the slot you chose before your load command executed.
        • • Press
          • • Press
            • • Press
      • Disk inserted in the mailslot but TRANSPORT FULL displays
      • The disk transport mechanism already contains a disk.
        • The disk transport mechanism already contains a disk.
        • • Refer to your host and application documentation for recovery procedures. If no procedures are ...
          • • Refer to your host and application documentation for recovery procedures. If no procedures are ...
            • • Refer to your host and application documentation for recovery procedures. If no procedures are ...
      • Disk inserted in the mailslot but MAILSLOT SENSOR displays
      • The jukebox mailslot sensors may have failed.
        • The jukebox mailslot sensors may have failed.
        • • Remove and then re-insert the disk. If this does not correct the problem, call your service rep...
          • • Remove and then re-insert the disk. If this does not correct the problem, call your service rep...
            • • Remove and then re-insert the disk. If this does not correct the problem, call your service rep...
      • Disk eject attempted but an EJECT ERROR message displays.
      • • Press CANCEL. Attempt to eject the disk again.
        • • Press
          • • Press
            • • Press
          • • If the light bar on the front panel is orange, cycle power to the jukebox* and try to eject the...
            • • If the light bar on the front panel is orange, cycle power to the jukebox* and try to eject the...
          • • If there is no disk in the mailslot and this error message repeats, call your service represent...
            • • If there is no disk in the mailslot and this error message repeats, call your service represent...
      • *Ensure that the SCSI bus is inactive before removing power to the jukebox. Removing power to a d...
      • Disk eject attempted but RESERVED displays.
      • The jukebox application software reserved the element for its use or a security configuration was...
        • The jukebox application software reserved the element for its use or a security configuration was...
        • • If appropriate, change this setting See “Setting an Operating Configuration” in this chapter. T...
          • • If appropriate, change this setting See “Setting an Operating Configuration” in this chapter. T...
            • • If appropriate, change this setting See “Setting an Operating Configuration” in this chapter. T...
      • Disk eject attempted but empty and then EJECT * displays.
      • This is not an error. There are no disks in the jukebox.
      • Disk eject attempted but TRANSPORT FULL displays.
      • The disk transport mechanism already contains a disk.
        • The disk transport mechanism already contains a disk.
        • • Refer to your host and application documentation for recovery procedures. If no procedures are ...
          • • Refer to your host and application documentation for recovery procedures. If no procedures are ...
            • • Refer to your host and application documentation for recovery procedures. If no procedures are ...
      • Disk eject attempted but SOURCE NOW EMPTY displays.
      • The application software moved the disk from the slot you chose before your eject command executed.
        • The application software moved the disk from the slot you chose before your eject command executed.
        • • Press
          • • Press
            • • Press
      • Disk eject attempted but MAILSLOT FULL displays.
      • A disk is in the mailslot.
        • A disk is in the mailslot.
        • • Remove the disk from the mailslot.
          • • Remove the disk from the mailslot.
            • • Remove the disk from the mailslot.
            • Select
      • You want to stop a test that is running.
      • Press CANCEL. The current test loop continues until finished, then the test stops.
      • *Ensure that the SCSI bus is inactive before removing power to the jukebox. Removing power to a d...
      • RUN ISTAT TEST displays (this initializes the element status)
        • RUN ISTAT TEST
      • • Power cycle the jukebox.*
        • • Power cycle the jukebox.*
          • • Power cycle the jukebox.*
            • • Power cycle the jukebox.*
          • • Run the
            • • Run the
          • • If steps above do not result in a READY display, call your service representative.
            • • If steps above do not result in a READY display, call your service representative.
      • Can't write to the disk.
      • • Check the host file system access permissions.
        • • Check the host file system access permissions.
          • • Check the host file system access permissions.
            • • Check the host file system access permissions.
          • • Eject the disk and check that the write-protect tab on each side of the disk is in the write-en...
            • • Eject the disk and check that the write-protect tab on each side of the disk is in the write-en...
          • • Check your application software.
            • • Check your application software.
          • • If steps above are unsuccessful, call your service representative.
            • • If steps above are unsuccessful, call your service representative.
      • *Ensure that the SCSI bus is inactive before removing power to the jukebox. Removing power to a d...
      A Supplies and Customer Support

      • A Supplies and Customer Support
      • Overview of This Appendix
        • Overview of This Appendix
        • This appendix provides information on the following topics:
        • • supplies and accessories
          • • supplies and accessories
            • • supplies and accessories
          • • shipping screw specifications
            • • shipping screw specifications
          • • HP customer support
            • • HP customer support
      • supplies and accessories
        • supplies and accessories
          • supplies and accessories
        • A full range of computer supplies may be ordered through a Hewlett-Packard authorized dealer, sal...
        • You may also access the “Business Store” web site by selecting “Other Ways to Buy” from the main ...
        • Authorized dealers and sales offices can be found at
        • Table A-1 Basic Supplies and Accessories
          • Table A-1 Basic Supplies and Accessories
      • Item
      • HP Part Number
      • 9.1-and 8.6-Gbyte Optical Disks
        • 9.1-
      • Rewritable optical disk (4,096 bytes/sector, 9.1 Gbytes, single disk)
      • C7983A
      • Write-once optical disk (4,096 bytes/sector, 9.1 Gbytes, single disk)
      • C7984A
      • Rewritable optical disk (2,048 bytes/sector, 8.6 Gbytes, single disk)
      • C7985A
      • Write-once optical disk (2,048 bytes/sector, 8.6 Gbytes, single disk)
      • C7986A
      • Rewritable optical disk (1,024 bytes/sector, 9.1 Gbytes, single disk)
      • C7987A
      • Rewritable optical disk (512 bytes/sector, 9.1 Gbytes, single disk)
      • C7988A
      • 5.2- and 4.7-Gbyte Optical Disks
        • 5.2- and 4.7-Gbyte Optical Disks
      • Rewritable optical disk (2,048 bytes/sector, 5.2 Gbytes, single disk)
      • 88147J
      • Write-once optical disk (2,048 bytes/sector, 5.2 Gbytes, single disk)
      • 88146J
      • Rewritable optical disk (1,024 bytes/sector, 4.7 Gbytes, single disk)
      • 88143J
      • Write-once optical disk (1,024 bytes/sector, 4.7 Gbytes, single disk)
      • 88145J
      • 2.6- and 2.3-Gbyte Optical Disks
        • 2.6- and 2.3-Gbyte Optical Disks
      • Rewritable optical disk (1,024 bytes/sector, 2.6 Gbytes, single disk)
      • 92280F
      • Write-once optical disk (1,024 bytes/sector, 2.6 Gbytes, single disk)
      • 92290F
      • Rewritable optical disk (512 bytes/sector, 2.3 Gbytes, single disk)
      • 92279F
      • Write-once optical disk (512 bytes/sector, 2.3 Gbytes, single disk)
      • 92289F
      • SCSI Cables
        • SCSI Cables
      • 50-Pin Low-Density to 50-Pin High-Density
      • 1.0 m (3.3 ft) clip latch to thumb screw
      • K2296
      • 1.5 m (4.9 ft) clip latch to thumb screw
      • K2297
      • 0.9 m (2.9 ft) thumb screw to thumb screw
      • K2294
      • 1.5 m (4.9 ft) thumb screw to thumb screw
      • K2295
      • 50-Pin High-Density to 50-PinHigh-Density
      • 0.5 m (1.6 ft) thumb screw to thumb screw
      • C2955A
      • 1.0 m (3.3 ft) thumb screw to thumb screw
      • C2908A
      • 1.5 m (4.9 ft) thumb screw to thumb screw
      • C2956A
      • 2.0 m (6.5 ft) thumb screw to thumb screw
      • C2957A
      • 5.0 m (16.5 ft) thumb screw to thumb screw
      • C2958A
      • 68-Pin High-Density to 50-Pin Low-Density
      • 1.0 (3.3 ft) clip latch to thumb screw
      • C2915A
      • 2.0 m (6.5 ft) thumb screw to thumb screw
      • C2906A
      • 5.0 m (16.5 ft) thumb screw to thumb screw
      • C2907A
      • 20.0 m (65.6 ft) thumb screw to thumb screw
      • C2916A
      • 68-Pin High-Density to 68-Pin High-Density
      • 0.9 m (2.9 ft) thumb screw to thumb screw
      • C2911A
      • 2.5m (8.2 ft) thumb screw to thumb screw
      • C2924A
      • 10.0 m (32.8 ft) thumb screw to thumb screw
      • C2925A
      • 20.0 m (65.6 ft) thumb screw to thumb screw
      • C2926A
      • SCSI Terminators
        • SCSI Terminators
      • 50-pin active high-density (molded)
      • C2904A
      • 68-pin differential high-density (molded)
      • C2905A
      • Disk Cleaners
        • Disk Cleaners
      • See www.hp.com/go/optical
      • --
      customer support

      • customer support
        • customer support
      • If your jukebox fails and the suggestions in this user’s guide and accompanying documentation do ...
      • • If you have a service contract with HP, contact your local HP Response Center. Response Centers...
        • • If you have a service contract with HP, contact your local HP Response Center. Response Centers...
          • • If you have a service contract with HP, contact your local HP Response Center. Response Centers...
        • • If you do not have a service contract with HP, contact your nearest HP dealer or sales office. ...
          • • If you do not have a service contract with HP, contact your nearest HP dealer or sales office. ...
      • NOTE Before calling, please record the following information and have it ready when you contact y...
        • NOTE Before calling, please record the following information and have it ready when you contact y...
        • - model number of your jukebox
        • - serial number
        • - brand and model of your host computer
        • - brand and model of your host computer SCSI adapter
        • - jukebox application software you are using and its version
        • - any jukebox driver you may be using that is separate from your jukebox application software a...
      warranty

      • warranty
        • warranty
      • HP PRODUCT DURATION OF WARRANTY
      • C1104M/P, C1105M/P, C1106M/P, One Year
      • C1107M/P, C1110M/P
      • 1. HP warrants HP hardware, accessories and supplies against defects in materials and workmanship...
      • 2. HP warrants that HP software will not fail to execute its programming instructions, for the pe...
      • 3. HP does not warrant that the operation of HP products will be uninterrupted or error free. If ...
      • 4. HP products may contain remanufactured parts equivalent to new in performance or may have been...
      • 5. The warranty period begins on the date of delivery or on the date of installation if installed...
      • 6. Warranty does not apply to defects resulting from (a) improper or inadequate maintenance or ca...
      • 7. TO THE EXTENT ALLOWED BY LOCAL LAW, THE ABOVE WARRANTIES ARE EXCLUSIVE AND NO OTHER WARRANTY O...
      • 8. HP will be liable for damage to tangible property per incident up to the greater of $300,000 o...
      • 9. TO THE EXTENT ALLOWED BY LOCAL LAW, THE REMEDIES IN THIS WARRANTY STATEMENT ARE CUSTOMER’S SOL...
      B Operating This Jukebox on a SCSI Bus

      • B Operating This Jukebox on a SCSI Bus
      • SCSI:brief overview
        • SCSI:brief overview
          • SCSI:brief overview
        • General
          • General
          • The Small Computer System Interface (SCSI), is a contention-based bus that accommodates different...
        • The SCSI Bus
          • The SCSI Bus
          • The common SCSI buses are 50-pin and 68-pin. The 50-pin bus, which uses eight of its lines for da...
        • Initiators and Targets
          • Initiators and Targets
          • SCSI devices on the bus are either “initiators” or “targets.” An initiator (usually the host comp...
          • Initiators and targets identify themselves on the bus by a SCSI ID. The ID is designated by the u...
          • The narrow SCSI bus, with its eight data lines, can communicate with eight devices that have IDs ...
          • Priority of IDs ascends from lowest to highest but this ascending priority, however, is
          • The diagram below shows the linear addressing of a simple, narrow bus with the host adapter set a...
        • LUN addressing
          • LUN addressing
            • LUN addressing
          • SCSI IDs are the top-level method of addressing devices on the bus. Another method of addressing ...
          • The complex device is identified by a SCSI ID, but this complex device assigns logical unit numbe...
          • To use this form of addressing, however, the jukebox application software, the SCSI bus drivers a...
        • SCSI bus:transfer rates
          • SCSI bus:transfer rates
            • SCSI bus:transfer rates
          • Initially, the SCSI specification defined a 5 MB/s synchronous data transfer rate on the narrow b...
        • SCSI bus:termination
          • SCSI bus:termination
            • SCSI bus:termination
          • To keep signals on the SCSI bus from being reflected, “terminators” must be placed at each end of...
          • Depending on your SCSI device, termination is supplied by a using a physical connector, by flippi...
          • Termination is always at both physical ends of the bus.
        • SCSI bus:differential
          • SCSI bus:differential
            • SCSI bus:differential
            • SCSI bus:single-ended
          • The SCSI bus is electrically implemented in two ways: single-ended and differential. These terms ...
          • The differential bus uses two lines for each signal and measures the voltage difference between t...
        • SCSI bus:connectors
          • SCSI bus:connectors
            • SCSI bus:connectors
          • Narrow devices (50-pin) use the following connectors:
          • • 50-pin low-density clip Centronics-type (external)
            • • 50-pin low-density clip Centronics-type (external)
              • • 50-pin low-density clip Centronics-type (external)
              • This is a large connector that is similar to a printer cable. This type of connector is gradually...
            • • 50-pin high density Micro D (using thumbscrews or small clips) (external)
              • • 50-pin high density Micro D (using thumbscrews or small clips) (external)
            • • This connector is similar to a D-type connector, but smaller and with smaller pin holes placed ...
              • • This connector is similar to a D-type connector, but smaller and with smaller pin holes placed ...
            • • 50-pin low-density ribbon (usually internal to the host)
              • • 50-pin low-density ribbon (usually internal to the host)
          • Wide devices (68- pin) use the following connectors:
          • • 68-pin high density Micro D connector (external)
            • • 68-pin high density Micro D connector (external)
              • • 68-pin high density Micro D connector (external)
              • This connector is similar to a D-type connector, but longer and slimmer and with smaller pin hole...
            • • 68-pin high density ribbon (usually internal to the host)
              • • 68-pin high density ribbon (usually internal to the host)
      • SCSI:issues when adding devices with this jukebox
        • SCSI:issues when adding devices with this jukebox
          • SCSI:issues when adding devices with this jukebox
        • This jukebox is a “fast and narrow” SCSI device with the capability to connect to either a narrow...
        • In the diagram below, note that the single-ended (50-line) bus is brought directly onto the jukeb...
        • The
        • Figure B-1 Single-ended and Differential Interfaces on This Jukebox
          • Figure B-1 Single-ended and Differential Interfaces on This Jukebox
        • Adding Devices to the Bus
          • Adding Devices to the Bus
          • When considering adding other devices to the jukebox bus, you should consider the following:
          • • Will adding a device onto a bus with this jukebox interfere or degrade the performance of the j...
            • • Will adding a device onto a bus with this jukebox interfere or degrade the performance of the j...
              • • Will adding a device onto a bus with this jukebox interfere or degrade the performance of the j...
            • • If the decision is made to add other devices to the jukebox bus, what SCSI requirements must be...
              • • If the decision is made to add other devices to the jukebox bus, what SCSI requirements must be...
          • Before addressing some questions involved in deciding whether to place another device on the juke...
          • Consider the quantity of data that the bus will have to carry, the frequency of data transfer, an...
          • Mixing Wide and Narrow Devices
            • Mixing Wide and Narrow Devices
          • As a preliminary note to this discussion, HP highly recommends that you do NOT mix wide and narro...
          • Connecting devices of the same bus width, such as all narrow (50-pin) is a simple process of dais...
          • This method should only be implemented by an experienced systems integrator who is highly knowled...
          • Because a narrow device only has a 50-pin connector, it will not transmit the eight extra bits of...
          • The lower eight data lines transfer commands and messages, allowing all devices, regardless of si...
          • If mixing narrow and wide devices is unavoidable, use the configuration described below:
          • It is very important that the 68-pin to 50-pin cable is properly configured to assure that the ei...
          • Cable Lengths
            • Cable Lengths
          • Observe SCSI cable maximum lengths;
          • Termination
            • Termination
          • • Refer to the documentation that comes with your particular adapter to see how to apply terminat...
            • • Refer to the documentation that comes with your particular adapter to see how to apply terminat...
              • • Refer to the documentation that comes with your particular adapter to see how to apply terminat...
            • • Use active terminators to reduce noise sensitivity.
              • • Use active terminators to reduce noise sensitivity.
            • • Never terminate the bus at any place except the physical ends. Terminating the bus in the middl...
              • • Never terminate the bus at any place except the physical ends. Terminating the bus in the middl...
            • • If devices are on both sides of the host computer adapter (such as hard drives internal to the ...
              • • If devices are on both sides of the host computer adapter (such as hard drives internal to the ...
          • General
            • General
          • • Do not connect a single-ended bus to a differential bus. Damage can occur.
            • • Do not connect a single-ended bus to a differential bus. Damage can occur.
              • • Do not connect a single-ended bus to a differential bus. Damage can occur.
      • Default SCSI IDs in the Jukebox When Using Basic SCSI Addressing and When Using LUN Mode
        • Default SCSI IDs in the Jukebox When Using Basic SCSI Addressing and When Using LUN Mode
        • Table B-1 Default SCSI and LUN Setings in 4- and 6-Drive Jukeboxes
          • Table B-1 Default SCSI and LUN Setings in 4- and 6-Drive Jukeboxes
      • BUS 1
      • LUN Mode OFF
      • LUN Mode ON
      • ID
      • LUN
      • ID
      • LUN
      • JKBX ID
      • 6
      • 0
      • 6
      • 0
      • DRV 1 ID
      • 5
      • 0
      • 6
      • 1
      • DRV 2 ID
      • 4
      • 0
      • 6
      • 2
      • DRV 3 ID
      • 3
      • 0
      • 6
      • 3
      • DRV 4 ID
      • 2
      • 0
      • 6
      • 4
      • DRV 5 ID*
      • 1*
      • 0*
      • 6*
      • 5*
      • DRV 6 ID*
      • 0*
      • 0*
      • 6*
      • 6*
      * if installed
      Table B-2 Default SCSI and LUN Settings in the 10-Drive Jukebox

      • Table B-2 Default SCSI and LUN Settings in the 10-Drive Jukebox
      • BUS 1
      • LUN Mode OFF
      • LUN Mode ON
      • ID
      • LUN
      • ID
      • LUN
      • JKBX ID
      • 6
      • 0
      • 6
      • 0
      • DRV 1 ID
      • 5
      • 0
      • 6
      • 1
      • DRV 2 ID
      • 4
      • 0
      • 6
      • 2
      • DRV 3 ID
      • 3
      • 0
      • 6
      • 3
      • DRV 4 ID
      • 2
      • 0
      • 6
      • 4
      • BUS 2
      • LUN Mode OFF
      • LUN Mode ON
      • ID
      • LUN
      • ID
      • LUN
      • DRV 5ID
      • 5
      • 0
      • 5
      • 0
      • DRV 6 ID
      • 4
      • 0
      • 5
      • 1
      • DRV 7 ID
      • 3
      • 0
      • 5
      • 2
      • DRV 8 ID
      • 2
      • 0
      • 5
      • 3
      • DRV 9 ID
      • 1
      • 0
      • 5
      • 4
      • DRV 10 ID
      • 0
      • 0
      • 5
      • 5
      Table B-3 LUN Mapping of a 10-Drive Jukebox if “DRVs BUS 1” ID is Changed to an ID Different Than...

      • Table B-3 LUN Mapping of a 10-Drive Jukebox if “DRVs BUS 1” ID is Changed to an ID Different Than...
      • BUS 1
      • LUN Mode ON
      • BUS 2
      • LUN Mode ON
      • ID
      • LUN
      • ID
      • LUN
      • JKBX ID
      • 6
      • 0
      • DRV 1 ID
      • 5
      • 0
      • DRV 5ID
      • 4
      • 0
      • DRV 2 ID
      • 5
      • 1
      • DRV 6 ID
      • 4
      • 1
      • DRV 3 ID
      • 5
      • 2
      • DRV 7 ID
      • 4
      • 2
      • DRV 4 ID
      • 5
      • 3
      • DRV 8 ID
      • 4
      • 3
      • DRV 9 ID
      • 4
      • 4
      • DRV 10 ID
      • 4
      • 5
      Figure B-2 Four or Six Drives, One Host Adapter, Basic SCSI Addressing

      • Figure B-2 Four or Six Drives, One Host Adapter, Basic SCSI Addressing
      Displays on the Control Panel
      Under CHOOSE LUN MODE * menu >> LUN MODE OFF
      Under SCSI IDs * > VIEW IDs * >
      BUS 1 *>>JXBX ID 6 LUN 0
      DRV 1 ID 5 LUN 0
      DRV 2 ID 4 LUN 0
      DRV 3 ID 3 LUN 0
      DRV 4 ID 2 LUN 0
      DRV 5 ID 1 LUN 0 (if installed)
      DRV 6 ID 0 LUN 0 (if installed)
      Figure B-3 10 Drives, Two Host Adapters, Basic SCSI Addressing

      • Figure B-3 10 Drives, Two Host Adapters, Basic SCSI Addressing
      Displays on the Control Panel
      Under CHOOSE LUN MODE * menu >> LUN MODE OFF
      Under SCSI IDs * > VIEW IDs * >
      BUS 1 *>>JXBX ID 6 LUN 0
      DRV 1 ID 5 LUN 0
      DRV 2 ID 4 LUN 0
      DRV 3 ID 3 LUN 0
      DRV 4 ID 2 LUN 0
      BUS 2 *>>DRV 5 ID 5 LUN 0
      DRV 6 ID 4 LUN 0
      DRV 7 ID 3 LUN 0
      DRV 8 ID 2 LUN 0
      DRV 9 ID 1 LUN 0
      DRV 10 ID 0 LUN 0
      Figure B-4 Ten Drives, One Host Adapter, LUN Addressing, Controller/Drives Use Same IDs

      • Figure B-4 Ten Drives, One Host Adapter, LUN Addressing, Controller/Drives Use Same IDs
      Displays on the Control Panel
      Under CHOOSE LUN MODE * menu >> LUN MODE ON
      Under SCSI IDs * > VIEW IDs * >
      BUS 1 *>>JXBX ID 6 LUN 0
      DRV 1 ID 6 LUN 10
      DRV 2 ID 6 LUN 2
      DRV 3 ID 6 LUN 3
      DRV 4 ID 6 LUN 4
      BUS 2 *>>DRV 5 ID 5 LUN 0
      DRV 6 ID 5 LUN 1
      DRV 7 ID 5 LUN 2
      DRV 8 ID 5 LUN 3
      DRV 9 ID 5 LUN 4
      DRV 10 ID 5 LUN 5
      Figure B-5 Ten Drives, One Host Adapter, LUN Addressing, Controller/Drives Use Different IDs

      • Figure B-5 Ten Drives, One Host Adapter, LUN Addressing, Controller/Drives Use Different IDs
      Displays on the Control Panel
      Under CHOOSE LUN MODE * menu >> LUN MODE ON
      Under SCSI IDs * > VIEW IDs * >
      BUS 1 *>JXBX ID 6 LUN 0
      DRV 1 ID 5 LUN 0
      DRV 2 ID 5 LUN 1
      DRV 3 ID 5 LUN 2
      DRV 4 ID 5 LUN 3
      BUS 2 *>>DRV 5 ID 4 LUN 0
      DRV 6 ID 4 LUN 1
      DRV 7 ID 4 LUN 2
      DRV 8 ID 4 LUN 3
      DRV 9 ID 4 LUN 4
      DRV 10 ID 4 LUN 5
      Table B-4 Possible Additional SCSI Addresses Available

      • Table B-4 Possible Additional SCSI Addresses Available
      • No. of Drives
      • LUN Mode OFF (basic SCSI addressing)
      • LUN Mode ON - (drives and jukebox controller use the same ID)
      • LUN Mode ON - (drives and jukebox controller use different IDs)
      • 4
      • Two SCSI addresses are available for connecting other devices.
      • Six SCSI addresses are available for connecting other devices to Bus 1.
      • Five SCSI addresses are available for connecting other devices to Bus 1.
      • 6
      • No additional devices can be connected.
      • 10
      • Two SCSI addresses are available on Bus 1 and 1 SCSI address is available on Bus 2 for connecting...
        • Two SCSI addresses are available on Bus 1 and 1 SCSI address is available on Bus 2 for connecting...
        • (In a 10 drive jukebox, four drives are mounted on Bus 1 and 6 drives are mounted on Bus 2.)
      • If Bus 1 and Bus 2 are daisy-chained, five SCSI addresses are available for other devices.
        • If Bus 1 and Bus 2 are daisy-chained, five SCSI addresses are available for other devices.
        • If Bus 1 and Bus 2 are NOT daisy-chained, six SCSI addresses are available on Bus 1 and six SCSI ...
      • If Bus 1 and Bus 2 are daisy-chained, four SCSI addresses are available for other devices.
        • If Bus 1 and Bus 2 are daisy-chained, four SCSI addresses are available for other devices.
        • If Bus 1 and Bus 2 are NOT daisy-chained, five SCSI addresses are available on Bus 1 and six SCSI...
      regulatory compliance

      • regulatory compliance
        • regulatory compliance
        • safety regulations compliance
      • Overview of this Appendix
        • Overview of this Appendix
        • This appendix contains important safety and regulatory information for the United States, Finland...
      • CDRH Regulations (USA Only)
        • CDRH Regulations (USA Only)
        • The Center for Devices and Radiological Health (CDRH) of the U.S. Food and Drug Administration im...
        • WARNING Use of controls, adjustments or performing procedures other than those specified in this ...
          • WARNING Use of controls, adjustments or performing procedures other than those specified in this ...
        • NOTE Complies with 21 CFR Chapter 1 Subchapter J.
          • NOTE Complies with 21 CFR Chapter 1 Subchapter J.
        • Laser Class Information: A black on yellow label which reads, "Class 1 Laser Product" printed in ...
      • EC Radio Frequency Interference Statement (Europe Only)
        • EC Radio Frequency Interference Statement (Europe Only)
        • WARNING This is a class A product. In a domestic environment this product may cause radio interfe...
          • WARNING This is a class A product. In a domestic environment this product may cause radio interfe...
      • United Kingdom Telecommunications Act 1984
        • United Kingdom Telecommunications Act 1984
        • The Hewlett-Packard 1200mx and 2200mx jukeboxes are approved under Approval Number NS/G/1234/J/10...
      • Declaration of Conformity
        • Declaration of Conformity
      • Herstellerbescheinigung
        • Herstellerbescheinigung
        • Diese Information steht im Zusammenhang mit den Anforderungen der Maschinenlärn information svero...
        • Schalldruckpegel Lp < 70 dB(A)
        • • am arbeitsplatz
          • • am arbeitsplatz
            • • am arbeitsplatz
          • • normaler betrieb
            • • normaler betrieb
          • • nach ISO 7779:1988/EN 27779:1991 (Typprüfung)
            • • nach ISO 7779:1988/EN 27779:1991 (Typprüfung)
        • English Translation of German Sound Emission Directive
          • English Translation of German Sound Emission Directive
          • This statement is provided to comply with the requirements of the German Sound Emission Directive...
          • • at operator position
            • • at operator position
              • • at operator position
            • • normal operation
              • • normal operation
            • • according to ISO 7779: 1988/EN 27779: 1991 (type test)
              • • according to ISO 7779: 1988/EN 27779: 1991 (type test)
      • Turvallisuusyhteenveto
        • Turvallisuusyhteenveto
        • Laserturvallisuus
          • Laserturvallisuus
          • LUOKAN 1 LASERLAITE
            • LUOKAN 1 LASERLAITE
              • LUOKAN 1 LASERLAITE
            • KLASS 1 LASER APPARAT
              • KLASS 1 LASER APPARAT
          • Hewlett-Packard 1200mx ja 2200mx optiset levymuistiasemat ovat käyttäjän kannalta turvallisia luo...
          • VAROITUS !
            • VAROITUS !
              • VAROITUS !
          • Laitteen käyttäminen muulla kuin käyttöohjeessa mainitulla tavalla saattaa altistaa käyttäjän tur...
          • VARNING !
            • VARNING !
              • VARNING !
          • Om apparaten används på annat sätt än i bruksanvisning specificerats, kan användaren utsättas för...
        • Huolto
          • Huolto
          • Hewlett-Packard 1200mx ja 2200mx levymuistiasemien sisällä ei ole käyttäjän huollettavissa olevia...
          • VARO !
            • VARO !
              • VARO !
          • Mikäli luku-/kirjoitusyksikön suojakotelo avataan ja suojalukitus ohitetaan, olet alttiina lasers...
          • VARNING !
            • VARNING !
              • VARNING !
          • Om skyddshöljet av den optiska drivmodulen öppnas och spärren urkopplas då apparaten är i funktio...
          • Aallonpituus
            • Aallonpituus
              • Aallonpituus
              • 660 nm
                • 660 nm
            • Teho
              • Teho
              • 60 mW
                • 60 mW
            • Turvallisuusluokka
              • Turvallisuusluokka
              • 3B
                • 3B
      • English Translation of Finland Regulatory Information
        • English Translation of Finland Regulatory Information
        • LASER SAFETY SUMMARY
        • The jukebox was type approved in Finland for laser safety by the National Board of Labour Protect...
        • WARNING !
          • WARNING !
            • WARNING !
        • The use of the product otherwise than specified in the user's manual may expose the user to laser...
        • SERVICE
          • SERVICE
            • SERVICE
        • There are no user serviceable parts inside the jukebox. The jukebox products can be serviced only...
        • WARNING !
          • WARNING !
            • WARNING !
        • If the enclosure of the optical drive mechanism is opened and the safety interlock disabled, you ...
        • Wavelength
          • Wavelength
            • Wavelength
            • 660 nm
              • 660 nm
          • Power
            • Power
            • 60 mW
              • 60 mW
          • Class
            • Class
            • 3B laser
              • 3B laser
      • Japanese VCCI Statement
        • Japanese VCCI Statement
        • This equipment is in the Class A category information technology equipment based on the rules of ...
      Glossary

      • Glossary
      • C-D
        • C-D
        • cartridge
          • cartridge
          • A plastic enclosure that contains an optical disk. The cartridge is labeled "A" or "B" to denote ...
            • A plastic enclosure that contains an optical disk. The cartridge is labeled "A" or "B" to denote ...
        • disk
          • disk
          • See optical disk.
            • See optical disk.
        • driver
          • driver
          • A program that allows the operating system to communicate with a peripheral device.
            • A program that allows the operating system to communicate with a peripheral device.
      • E-L
        • E-L
        • element
          • element
          • A SCSI term for any one of the autochanger components — drive, mailslot, storage slots, or picker.
            • A SCSI term for any one of the autochanger components — drive, mailslot, storage slots, or picker.
        • jukebox
          • jukebox
          • A term synonymous with optical disk library or autochanger. This type of optical storage device i...
            • A term synonymous with optical disk library or autochanger. This type of optical storage device i...
        • jukebox controller
          • jukebox controller
          • The part of the jukebox that controls the sending and receiving of SCSI commands and controls the...
            • The part of the jukebox that controls the sending and receiving of SCSI commands and controls the...
        • LAN
          • LAN
          • Local area network. A group of computers and peripherals physically connected so users can share ...
            • Local area network. A group of computers and peripherals physically connected so users can share ...
      • M-O
        • M-O
        • magneto-optical
          • magneto-optical
          • A type of optical technology which uses a laser to read from and write to a magnetic layer on an ...
            • A type of optical technology which uses a laser to read from and write to a magnetic layer on an ...
        • mailslot
          • mailslot
          • The area where disks are inserted and removed from the jukebox.
            • The area where disks are inserted and removed from the jukebox.
        • multifunction drive
          • multifunction drive
          • An optical disk drive that supports both rewritable and write-once optical disks. The drive detec...
            • An optical disk drive that supports both rewritable and write-once optical disks. The drive detec...
        • optical disk
          • optical disk
          • A term synonymous with the 5.25-inch magneto-optical disk. There are two types of optical disks u...
            • A term synonymous with the 5.25-inch magneto-optical disk. There are two types of optical disks u...
        • optical disk library
          • optical disk library
          • See jukebox.
            • See jukebox.
      • R-T
        • R-T
        • rewritable optical
          • rewritable optical
          • An optical disk technology in which data can be repeatedly written using magneto- optical reading...
            • An optical disk technology in which data can be repeatedly written using magneto- optical reading...
        • SCSI
          • SCSI
          • An acronym for the Small Computer Systems Interface. See Appendix B for a more detailed explanati...
            • An acronym for the Small Computer Systems Interface. See Appendix B for a more detailed explanati...
        • storage slot
          • storage slot
          • An are of the autochanger that holds cartridges when the cartridges are not in a drive or not bei...
            • An are of the autochanger that holds cartridges when the cartridges are not in a drive or not bei...
        • terminator
          • terminator
          • A resistor array device used for electrically terminating a SCSI bus. A SCSI bus must be terminat...
            • A resistor array device used for electrically terminating a SCSI bus. A SCSI bus must be terminat...
      • W
        • W
        • write-once
          • write-once
          • An additional operating mode available with multifunction drives. When a write-once disk is inser...
            • An additional operating mode available with multifunction drives. When a write-once disk is inser...
        • write protect
          • write protect
          • A feature that prevents data from being written to a disk. A write protect tab is located on both...
            • A feature that prevents data from being written to a disk. A write protect tab is located on both...
              • Numerics
              • A
              • C
              • D
              • E
              • I
              • L
              • M
              • O
              • P
              • R
              • S
              • T
              • U
              • V
              • W
      Popular Brands

      • Apple
      • Bissell
      • Brother
      • Canon
      • Casio
      • Cisco
      • Craftsman
      • Dell
      • FRIGIDAIRE
      • Garmin
      • GE
      • Honeywell
      • HP
      • John Deere
      • Kenmore
      • LG
      • Maytag
      • Motorola
      • NETGEAR
      • Nikon
      • Panasonic
      • Pioneer
      • Samsung
      • Sharp
      • SINGER
      • Sony
      • Whirlpool
      • Yamaha

      Popular manuals

      • Canon - AE-1
      • Fitbit - Flex
      • Nikon - D5000
      • Nikon - D40
      • Nikon - D3100
      • Nikon - D90
      • Nikon - D7000
      • Nikon - D80
      • Nikon - D3000
      • HP - Officejet Pro 8600
      • Canon - EOS 60D
      • HP - 12C Financial calculator