Index – HEIDENHAIN TNC 320 (77185x-01) User Manual
Page 578
Index
578
TNC 320 | User's Manual
HEIDENHAIN Conversational Programming | 3/2014
Index
3
3-D touch probes
Calibration.............................. 438
3-D view................................... 474
A
Accessing tables...................... 301
Accessories................................ 79
Actual position capture............... 93
Adding comments............ 127, 129
Additional axes..................... 83, 83
Adjusting spindle speed........... 423
Angle functions........................ 274
Approach contour..................... 188
ASCII Files................................ 369
Automatic program start.......... 494
Automatic tool measurement... 161
B
Basic rotation........................... 444
mode...................................... 444
Block.......................................... 95
Delete...................................... 95
C
Calculating with parentheses... 311
Calculation of circles................ 275
Calculator................................. 131
Chamfer................................... 198
Circle........................ 202, 204, 210
Circle center............................. 200
Circular path..................... 201, 210
Code numbers......................... 506
Comparison.............................. 549
Compensating workpiece
misalignment
straight surface...................... 443
Connecting/removing USB devices.
interfaces................................. 536
Context-sensitive help.............. 145
Control panel.............................. 66
Conversational dialog................. 91
Coordinate transformation........ 366
Copying program sections.... 96, 96
Corner rounding....................... 199
D
Data Backup............................. 101
Data interface........................... 507
Connector pin layouts............ 536
Set up.................................... 507
Data output on the screen....... 288
Data transfer software............. 511
507, 508, 508, 508, 508, 509, 509
Datum management................ 425
Datum setting.......................... 424
Without a 3-D touch probe..... 424
Datum shift
Resetting................................ 368
Using the datum table............ 367
Datum table............................. 436
Transferring test results.......... 436
Defining local Q parameters..... 270
Defining nonvolatile Q parameters..
Defining the workpiece blank..... 90
Depart contour......................... 188
Dialog......................................... 91
Directory.......................... 102, 106
Copy....................................... 108
Create.................................... 106
Delete.................................... 110
Displaying HTML files.............. 115
Displaying Internet files............ 115
Display screen............................ 65
Downloading help files............. 150
E
Enter spindle speed................. 170
Error messages................ 139, 139
Help with............................... 139
Ethernet interface.................... 513
Configuring............................. 513
network drives....................... 121
Connection options................ 513
Introduction............................ 513
External access........................ 501
External data transfer
iTNC 530................................ 119
F
FCL........................................... 506
FCL function................................ 9
Feature Content Level.................. 9
Feed rate.................................. 422
Adjust..................................... 423
Input options............................ 92
On rotary axes, M116............. 402
movements M103.................... 345
Feed rate in millimeters per spindle
revolution M136....................... 346
File
Create.................................... 106
File functions............................ 365
File manager...................... 99, 102
Call......................................... 104
Copying files.......................... 106
Copying tables....................... 108
Delete file.............................. 110
Directories.............................. 102
Copy................................. 108
Create.............................. 106
External data transfer............. 119
File
Create.............................. 106
File type................................... 99
File type
External file types............ 101
Function overview.................. 103
Overwriting files..................... 107
Protect file.............................. 113
Rename file.................... 112, 112
Selecting files......................... 105
Tagging files........................... 111
File status................................ 104
Filter for hole positions with DXF
data update.............................. 249
Firewall.................................
FK programming.............. 215, 215
Circular paths......................... 221
Fundamentals......................... 215
FK-Programming
Graphics................................. 217
FK programming
Initiating dialog....................... 219
Input options.......................... 222
Auxiliary points................. 225
Circle data........................ 223
Closed contours............... 224
contour elements................. 222
End points........................ 222
Relative data.................... 226
Straight lines.......................... 220
messages......................... 281, 281
FN16: F-PRINT: Output of formatted
texts................................. 285, 285
data.................................. 289, 289
FN19: PLC: Transfer values to the
PLC.................................. 298, 298
synchronization......................... 298
FN23: CIRCLE DATA: Calculate a
circle from 3 points.................. 275
FN24: CIRCLE DATA: Calculate a
circle from 4 points.................. 275
definable table......................... 376
FN27: TABWRITE: Write to a freely
definable table.................. 377, 377
freely definable table........ 378, 378