Harken 1036 MKIII Jib Reefing & Furling - Manual (Page 11)

Sailmaker Instructions
Luff Tape • Tack and Head Shackles • Suncover
May 2002 Unit 3 MKIII 6
■ Sail Type
The Harken furler will work with conventional sails or
sails with built in shaping devices such as Aeroluff
® ,
Pirini Luff or foam luff.
■ Luff Length
Note offsets above and below the sail.
If a toggle or link plates are used below the furler to
raise the drum (see page 8), make sure you deduct this
from the sail luff length.
If the luff of the sail is not long enough to put the
halyard swivel near the top of the headstay foil,
make sure a pendant is added, see page 30.
■ Tack Setback
Note setback for the tack shackle and cut the sail
accordingly.
■ Luff Tape Size
Unit 3 requires number 6 (
6 /
32
" or 5 mm)
luff tape.
■ Luff Tape Length
Cut off the top of the luff tape so it is 20 to 30" (500 to
760 mm) below the head of the sail. This will allow the
head to lag behind the rest of the sail to help flatten
the sail. It will also help the head to roll more smoothly.
Note feeder height and extend the bottom of the luff tape
downwards so it is below the feeder. This will prevent
the luff tape from catching in the feeder as the sail is
lowered. *The 39
3 /
4
" (1010 mm) minimum pertains to
shortened bottom foil installation, see page 13. Other
installations will have a minimum feeder height of
47
1 /
4
" (1200 mm).
*If bottom foil is to be cut
for proper installation.
■ Tack and Head Shackles
Make sure tack and head
shackles fit the sail rings.
The minimum inside
dimensions of the standard
head and tack shackles are:
(A) 1
7 /
8
" (48 mm)
(B) 13 /
16
" (21 mm)
■ Suncover
Suncovers may be installed on either side of the sail.
However, make sure you match other sails in the cus-
tomer’s inventory.
Foil
7 3 /
4
"
197 mm
Halyard Shackle
Manille de Drisse
Fall-Schäkel
Grillo Drizza
Head Shackle
Manille de Point de Drisse
Kopf-Schäkel
Grillo Penna
Feeder Entrance
Entrée d’Engoujure
Einfädler
Ingresso Feeder
Tack Shackle
Manille de Point d’Amure
Fuss-Schaëkel
Grillo Mura
Pivot Point
Point de Pivotement
Dreh-punkt
Snodo
Clevis Pin
Axe Épaulé
Toggelbolzen
Perno
12"
305 mm
16 1 /
8 "
410 mm
1 3 /
4
"
44 mm
53 1 /
4
" Max
1352 mm
39 3 /
4
" Min
1010 mm
12"
308 mm
11 7 /
8
"
302 mm
9" Max
229 mm
6" Min
152 mm
17" Max
432 mm
14" Min
356 mm
20 1 /
2
" Max
521 mm
17 1 /
2
" Min
445 mm
Actual Size
Echelle 1, Tatsächliche Grsse, Dimensioni Reali
3 /
4
", 7 /
8
"
19.1 mm, 22.30 mm
A
B