Sizing check unit 1 contains a, Or sta-lok, Stud with special dyform wedge – Harken 882 MKIII Jib Reefing & Furling User Manual
Page 6
October 2001
Unit 1 MKIII
3
16 Feeder
Engageur
Einfädler
Feeder
17 Regular Foil Extrusion
Profil standard (2130 mm)
Normales Profil
Estruso
18 Connector
Connecteur
Verbinder
Connettore
19 Conector Locking Wedges
Cales plastiques pour connecteurs
Kunststoff Keile
Piastrine di bloccaggio connettori
12 Threaded Stud w/Terminal
Embout fileté à sertir
Gewinde-Terminal
Terminale filettato
13 Torque Tube
Tube de torsion
Mitnehmerhülse
Tubo di torsione
14 Bottom Foil Extrusion
Profil infèrieur standard
Unterstes Profil
Estruso inferiore
15 Bottom Foil Connector
Connecteur inférieur
Unterstes Verbinder
Connettore inferiore
20 Connector Screws
Vis pour connecteurs
Schrauben für Verbinder
Viti di bloccaggio connettori
21 Halyard Swivel
Emérillon de drisse
Fallwirbel
Girella superiore (Drizza)
22 Top Foil Extrusion
Profil plastique pour connecteurs
Top Profil
Estruso superiore
23 Connector
Connecteur
Verbinder
Connettore
24 Top Foil Trim Cap
Capuchon plastique supérieur
Topkappe
Cappuccio per estruso superiore
25 Upper Swage Eye
Embout serti supérieur à œil
Oberes Augterminal
Terminale ad occhio pressato
Harken Threaded Studs
Terminaisons Harken
Harken Terminals
Terminali Harken
Wire/Rod
Taille du Câble
ou du Rod
Draht o Rod Grösse
Dimensione del cavo
o del tondino
Swage
Embout à sertir
Walz- Terminal
Terminale a pressare
Sta-Lok
Norseman
Rod
Rod
Rod
Tondino
1
/
4
"
Part No.
Ref.
Art. -Nr.
Num.
817
Part No.
Ref.
Art. -Nr.
Num.
821
Part No.
Ref.
Art. -Nr.
Num.
—
9
/
32
"
818
822
—
6 mm
873
880
—
7 mm
874
822
—
*8 mm
879
881
—
**-8 (5.7 mm)
—
—
823-8
**-10 (6.4 mm)
—
—
823-10
*Type 316 stainless steel only **Nitronic 50 Rod Only
*Acier inox type 316 seulement **Nitronic 50 Rod Only
*Nur 316er Niro **Nitronic 50 Rod Only
*Solo acciaio inox 316 **Solo tondino Nitronic 50
■
Sizing Check
Unit 1 contains a
1
/
2
" (12.7 mm) clevis pin. Make sure you have
the correct size pin for your boat. Harken does not
recommend drilling the chainplate or the integral toggle.
Check to make sure the lower drum assembly will fit inside
the bow pulpit. If there is an anchor locker, check to see if the
drum assembly will clear. If necessary, use a toggle or link
plates to raise the unit. See page 8.
■
Threaded Headstay Stud
Order a Harken threaded stud to match headstay wire or rod size.
■
Dyform
®
Wire
The maximum Dyform wire size for the Unit 1 is
9
/
32
" (7 mm).
Dyform requires special terminals. Use Norseman
®
or Sta-Lok
®
stud with special Dyform wedge.
Pivot
Point
Clevis Pin
7
7
/
16
"
188 mm
6
7
/
8
"
184 mm
5
1
/
4
" Max 133 mm
3
3
/
4
" Min 95 mm
9
7
/
8
" Max
251 mm
8
3
/
8
" Min
213 mm
12
1
/
4
" Max
311 mm
10
3
/
4
" Min
273 mm