Comtech EF Data DMD-2050E User Manual

Dmd-2050e

This manual is related to the following products:

DMD20 DMD20LBST DMD-2050 DMD50

Table of contents

Document Outline

DMD-2050E REV 2
- DMD-2050E
  - Universal Satellite Modem
  - Installation and Operation Manual
Errata A, Theory of Operation
Errata B, Chapters 3 and 4
Table of Contents
- Part Number MN-DMD2050E
Preface
- PREFACE
1 Introduction
- 1.1 Overview
- 1.2 DMD2050E Configurations
- 1.3 Configurations and Options
2 Installation
- 2.1 Unpacking and Inspection
- 2.2 Installation Safety
- 2.3 Installation Considerations
- 2.4 Initial Configuration Check
  - 2.4.1 Standard Factory Configuration
- 2.5 Modulator Checkout
  - 2.5.1 Initial Start Up
  - 2.5.2 Factory Terminal Settings
3 Theory of Operation
- Chapter 3. Theory of Operation
4 User Interfaces
- Chapter 4. User Interfaces
5 External Connections
- 5.1 Power Connectors, Ground and Switches
  - 5.1.1 Ground Connector
  - 5.1.2 Power Switch
- 5.2 Front Panel Connections
  - 5.2.1 Key Loader Interface
- 5.3 Rear Panel Connectors
6 Maintenance and Troubleshooting
- Chapter 6. Maintenance and Troubleshooting
7 Technical Specifications
- 7.1 Modulator
- 7.2 Demodulator
- 7.3 Plesiochronous Buffer
- 7.4 Monitor and Control
- 7.5 Terrestrial Interfaces
- 7.6 IBS/Synchronous Interface (Standard)
- 7.7 High-Speed Serial Interface (HSSI) & Gigi Ethernet Data Interface
- 7.8 Key loader interface
- 7.9 Environmental
- 7.10 Physical
- 7.11 Data Rate Limits
  - 7.11.1 Non-DVB
  - 7.11.2 DVB
- 7.12 BER Specifications
- 7.13 AGC Output Voltage
App A Product Options
- A.1 Hardware Options
- A.2 Custom Options
App B Front Panel Upgrade Procedure
- B.1 Introduction
- B.2 Required Equipment
- B.3 Procedures
App C Carrier Control
- C.1 Carrier Control and Alarms
- C.2 Carrier States and Changes to Programming
- C.3 Carrier States
App D Web Browser Setup Guide
- D.1 Introduction
- D.2 Setup
  - D.2.1 TCP-IP Menus
  - D.2.2 IP Address
- D.3 Web Interface Security
- D.2 Reset a User Account
- D.3 Confirmation
- D.4 Equipment Website
  - D.4.1 Log in to the Equipment Website
- D.5 Web Page Appearance
- D.6 Configure Web Browsers for the Radyne WEB Interface
App E Efficient Drop
- E.1 Introduction
- E.2 System Requirements
- E.3 Configuration Examples
- E.4 Functional Descriptions
- E.5 Configuring the Modem for Drop and Insert
- E.6 D&I Maps and Map Editing
- E.7 Efficient Drop and Insert Introduction
- E.8 Prerequisite
- E.9 Efficient Drop and Insert Mode
App F TCPIP Ethernet Setup
- F.1 Introduction
- F.2 TCP/IP Network Configuration
- F.3 Network Configuration Summary
- F.4 Ethernet Test
  - F.4.1 Connecting the Modem Ethernet Cable to a Network Link
  - F.4.2 Connecting the Modem Ethernet Cable Directly to a Computer (without a Network)
- F.5 Testing the Ethernet Connection using the Ping Program (Optional)
App G AUPC
- Appendix G. AUPC Operation
  - G.1 Automatic Uplink Power Control (AUPC Operation)
App H Ethernet Data Interface Setup
- H.1 Configuring the modem to use the Ethernet Data Interface (Optional)
App I Strap Codes
- I.1 Strap Codes
  - I.1.1 An example of how to set a strap code
- I.2 Sample Applications
  - I.2.1 Operational Case Examples
App J ITA
- Appendix J. ITA Operation
  - J.1 Information Throughput Adaptation (ITA Operation)
    - J.1.1 Properties of ITA on the DMD2050E:
    - J.1.2 Basic Setup (Example)
Addendum TRANSEC
Cover_Back