Generac 86640 User Manual
Service manual
Attention! The text in this document has been recognized automatically. To view the original document, you can use the "Original mode".
Table of contents
Document Outline
- SERVICE
- Manual
- Foreword
- Section 1.1- HOW GENERATORS PRODUCE ELECTRICITY
- Section 1.3- INSULATION RESISTANCE TESTS
- Section 1.4- INTRODUCTION TO TROUBLESHOOTING
- Section 1.5- TROUBLESHOOTING FLOW CHART
- Using the Troubleshooting Flow Chart
- Introduction
- Test 1> Check No-Load Voltage and Frequency
- Test 2- Check Load Voltage and Frequency
- Test 3- Check Load Watts and Amperes
- Test 6- Do a Fixed Excitation Test
- Test 7- Check Wires 1 and 4
- Test 8- Check Rotor
- Test 9> Check Brushes and Slip Rings
- Test 10- Test Main Circuit Breaker
- Test 11- Check AC Power Lead Connections
- Test 12- Test DPE Circuit Breaker
- Test 12< Test DPE Circuit Breaker (Continued)
- Test 13- Test Thermal Protector
- Test 14- Test Stator DPE Windings
- Test 15- Test Stator AC Power Windings
- Test 16- Check Sensing Leads
- Test 17- Check Voltage Regulator
- Test 17- Check Voltage Regulator (Continued)
- Introduction
- Tightening Cylinder Head Boits
- Tighten Manifoid, Exhaust Manifoid and Carburetor Fasteners INTAKE MANIFOLD NUTS:
- Adjusting Vaive Clearance
- Checking Drive Beits
- Measuring Compression Pressure
- Timing Belt Precautions
- Timing Beit Removai
- Timing Belt Installation
- Cylinder Head Removal
- Checking Cylinder Head Distortion
- Checking Cylinder Head Distortion (Continued)
- Valve Guide Replacement
- Valve Inserts
- Camshaft Bearing Clearance
- Valve Dimensions
- Valve Spring Squareness, Free Length and Tension
- Cylinder Head Assembly
- Cylinder Head Assembly (Continued)
- Installation
- Oil Pump Removal
- Inspection
- Installation
- Camshaft Oil Seal Replacement
- Crankshaft Front Oil Seal Replacement
- Disassembly
- Inspection
- Assembly (Continued)
- Section 3.1- LUBRICATION SYSTEM FAMILIARIZATION
- Section 3.2- ENGINE OIL PUMP
- Section 4.1- COOLING SYSTEM FAMILIARIZATION
- Section 4.2- WATER PUMP AND THERMOSTAT
- Section 4.3- COOLING AND VENTILATING AIR
- Section 4.4- OPTIONAL REMOTE RADIATOR FAN
- Section 4.5- OPTIONAL HEAT RECOVERY SYSTEM
- General
- Operation
- Customer Remote Heater
- Exploded View of Heat Recovery System
- TABLE OF CONTENTS
- TABLE OF CONTENTS
- TABLE OF CONTENTS
- Section 7.1- MECHANICAL GOVERNOR
- Section 7.2- ELECTRONIC GOVERNOR
- LirJ
- Section 8.2- TESTS, CHECKS AND ADJUSTMENTS
- Ignition Coil
- Checking the Condenser
- Distributor Cap and Rotor Head
- Contact Set
- Check Governor Advance
- Spark Plugs (Continued)
- Ignition Timing
- Checking Ignition Wires
- TABLE OF CONTENTS
- Components
- DC Alternator
- DC Voltage Regulator
- Introduction
- DC Alternator Description
- DC Alternator Adjustments
- Testing
- Testing (Continued)
- Cranking System Description
- Operational Analysis
- Engine Control Circuit Board
- Start-Stop Switch
- 10 Amp Circuit Breaker
- Starter Contactor
- starter Contactor (Continued)
- Starter
- Battery
- Battery (Continued)
- Section 9.4- ENGINE CONTROL CIRCUIT
- Section 9.5- TROUBLESHOOTING GUIDE
- •l
- Problem 2. Engine Cranks But Will Not Start
- Test 8- Check Wire 56 Volts at Starter Contactor (Continued) ROCEDURE:
- Test 9- Check Starter Contactor Ground
- Test 10. Check Wire 56
- Test 12- Test Start-Stop Switch
- Test 13. Check Power Supply to Circuit Board
- Test 11. Test 10 Amp Circuit Breaker
- Test 14. Check Fuel Supply
- Test 15. Check Engine Control Circuit Board Wire #14 Output
- Test 16. Check Fuel Valve
- Test 17. Check Fuel Pump
- Test 18. Test Automatic Choke
- Test 19. Check Engine Ignition System
- Test 20. Check Engine Fuel System
- Test 21- Check Engine Mechanical Systems
- Section 10.1- REMOTE START-STOP PANELS
- Section 10.2- REMOTE GAUGE PANEL