Yamaha FX770 - Manual (Page 71)

Section 8: Specifications
RECEPTION FORMAT -
© Note On
This message is received on the MIDI channel specified in
the currently selected BANK when CONTROLLER 1 or
CONTROLLER 2 is assigned to NOTE ON VELOCITY.
When a NOTE ON message is received, the value of the
assigned effect parameter is changed according to received
the velocity value.
And, when the EFFECT TYPE of PITCH SECTION is
SPI, this is received as message to control pitch shift value.
The velocity value is ignored Reception is not possible
when the base KEY parameter is OFF.
status 1001 nnnn rmnn = channel # *1
1st data Okkk kkkk kkkkkkk = note nuinber *4
2nd data Owv ww vwww = velocity *5
© CONTROL CHANGE
This message is received on the MIDI channel specified in
the currently selected BANK when CONTROLLER 1 or
CONTROLLER 2 is assigned to control number.
When a CONTROL CHANGE message is received, the
value of the assigned effect parameter is changed according
to the received control value.
status 1011 nnnn nnnn = channel number *1
1st data Occc cccc ccccccc = control number *6
2nd data Owv ww vwww = control value *7
® PROGRAM CHANGE
This message is received on the MIDI channel specified in
the currently selected BANK.
When a PROGRAM CHANGE message is received, the
effect program assigned to the received program number in
the program change assignment table of current BANK is
selected.
status 1100 nnnn
1st data Oppp pppp
nnnn = channel number *1
ppppppp = program number *8
© CHANNEL PRESSURE
This message is received on the MIDI channel specified in
the currently selected BANK when CONTROLLER 1 or
CONTROLLER 2 is assigned to CHANNEL PRESS.
When a CHANNEL PRESSURE message is received, the
value of the assigned effect parameter is changed according
to the received pressure value.
status 1101 nnnn
1st data Ovw ww
nnnn = channel number *1
vwww = pressure value *9
ACTIVE SENSING
After ACTIVE SENSING has been received, if the interval
time is more than 300 milli seconds, the MIDI volume is set
to maximum.
nil
1110 active sensing
TIMING CLOCK
For the following effect type, when the TRG parameter is
MIDI, modulation speed or delay time is set to interval time
of TIMING CLOCK.
nil
1000 timing clock
section effect type
parameter to be set to interval
time of MIDI CLOCK
MOD PAN.TRM modulation speed
DELAY TD1,TD2,TMD delay time
© Program Data Bulk Dump Request
Received on the MIDI channel specified for the currently
selected bank.
When received, the data corresponding to the specified user
program is transmitted.
nnnn = channel # *1
status 1111 0000(FOh)
ID # 0100 0011(43h)
SUB STATUS 0010 nnnn nnnn
FORMAT # 0111 1110(7Eh)
header 0100 1100(4Ch) ”L"
0100 1101(4Dh)
0010 0000(20h)
" ”
0010 0000(20h) « ,,
0011 ,1000 (38h) "8"
0100 0001(41h) “A"
0011 0010(32h) ”2"
0011 0000(30h) "0"
data name 0100 1101(4Dh)
program # Ommm mrnrnm *2
EOX 1111 0111(F7h)
(8) Program Change Table Bulk Dump Request
Received on the MIDI channel specified for the currently
selected bank.
When received, the data corresponding to the program
change table of the specified bank is transmitted.
channel # *1
68
status 1111 0000(FOh)
ID # 0100 0011(43h)
SUB STATUS 0010 nnnn nnnn
FORMAT # 0111 1110(7Eh)
header 0100 1100(4Ch) "L"
0100 1101(4Dh) «M"
0010 0000(20h) « //
0010 0000(20h) U
H
0011 1000(38h) «8«
0100 0001(41h) "A"
0011 0010(32h) "2"
0011 0000(30h)
data name 0101 0100(54h)
bank # Obbb bbbb ♦3
EOX 1111 0111(F7h)